IFM ID002A Handleiding

IFM Niet gecategoriseerd ID002A

Lees hieronder de 📖 handleiding in het Nederlandse voor IFM ID002A (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 179 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
Operating instructions
(Ex protection related part) for inductive sensors
according to EU directive 94/9/EC annex VIII (ATEX)
group II, equipment category 3D
ID002A / ID502A
UK
80233522 / 00 11 / 2015
2
Remarks for safe use in hazardous areas
Functions and features
• Use in hazardous areas according to the classification
II 3D
(group II, category 3D, apparatus for dust atmosphere).
Complies with the reqirements of the standards EN 60079-0 and EN 60079-31.
• Marking
II 3D Ex tc IIIC T90°C Dc X IP65
• Permissible operating temperature of the application (proper usage):
Ta: -20°C...+60°C
Installation / Set-up
The units must only be installed, connected and set up by qualified staff. The qualified staff
must have knowledge of protection classes, regulations and provisions for apparatus in
hazardous areas.
Check whether the classification (see "Marking" above and marking on the unit) is suitable
for the application.
Installation remarks / Installation
• Adhere to the relevant national regulations and provisions.
• The relevant installation regulations must be adhered to. In particular, take into account the
requirements relating to the temperature limitation as regards the expected dust deposits.
• Avoid electrostatic charging on housings and cables.
• To avoid electrostatic charging steps must be taken to ensure the equalisation of potential
of metal parts (plug housing, fixing elements, etc.).
• Protect the units and the cables efficiently against damage.
• To avoid soiling, do not remove the dust caps from the cable glands or the plugs until
introducing the cables or attaching the socket.
• It is the responsiibility of the user to determine the appropriate tightening torques for
the type of cable used. The cable glands and the cap nut have to be firmly tightened.
If the connection thread or the cap nut is overtightened or undertightened, the type of
connection, the tightness and the strain relief are impaired.
• The housing screws are to be fastened with 0.5 Nm, the fixing screws with max. 4 Nm.
• Maintenance intervals are application-specific and therefore need to be defined by the
operator depending on the operating conditions.
• During maintenance, especially those parts on which the type of protection depends need
to be examined (e.g. integrity of the components of the cable gland, of the seals).
3
UK
Special conditions for safe operation
• For units with terminal chamber (cable gland) and cable units a sufficient strain relief must
be ensured or the cable must be firmly laid.
• Do not disconnect the cables of units with terminal chamber while live.
• The housing and housing parts made of plastic were tested in accordance with
EN 60079-0 for group II and for a low mechanical risk with an impact energy of 4 joules.
• Avoid direct radiation with high UV components (sunlight). Mount the unit in a protected
place.
• Where units require an additional fuse, this must be located outside the hazardous areas.
• Units of the type ID must be mounted on a flat surface and the entire bottom must lie
flat on the surface. When mounted with the ifm mounting sets E11121 or E11122, these
requirements are met.
Maintenance / repair
The unit must not be modified nor can it be repaired. In case of a fault please contact the
manufacturer.
Data sheets, EC declaration of conformity and EC type test certificates are available from
the manufacturer on request.

Product specificaties

Merk: IFM
Categorie: Niet gecategoriseerd
Model: ID002A

Heb je hulp nodig?

Als je hulp nodig hebt met IFM ID002A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd IFM

IFM

IFM MK5344 Handleiding

15 November 2024
IFM

IFM OL5029 Handleiding

15 November 2024
IFM

IFM EVC284 Handleiding

15 November 2024
IFM

IFM OB5022 Handleiding

15 November 2024
IFM

IFM AL4302 Handleiding

15 November 2024
IFM

IFM AC1006 Handleiding

12 November 2024
IFM

IFM AC1345 Handleiding

12 November 2024
IFM

IFM CR3122 Handleiding

12 November 2024
IFM

IFM DV1531 Handleiding

12 November 2024
IFM

IFM DV1501 Handleiding

12 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024