Icom RMK-3 Handleiding

Icom Radio RMK-3

Lees hieronder de 📖 handleiding in het Nederlandse voor Icom RMK-3 (2 pagina's) in de categorie Radio. Deze handleiding was nuttig voor 118 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

INSTRUCTIONS

SEPARATION KIT

RMK-3

Thank you for purchasing the RMK-3

SEPARATION KIT

The RMK-3 allows you to install the mobile trans-

ceiver front panel separately from the main body for

added installation convenience and operation. Use

either the optional OPC-607, OPC-608 or OPC-609

SEPARATION CABLE

with the RMK-3.

• In this instruction, the illustration is described using the IC-

F5060 series transceiver.

■ Separation

The optional OPC-607 , OPC-608 (3 m; 9.84 ft) (8 m; 26.3 ft) or

OPC-609* (1.9 m; 6.3 ft)

SEPARATION CABLE

is required for in-

stalling the transceiver front panel and main body separately.

*For Europe version, only the OPC-609 is available.

q Turn the transceiver’s power OFF, then disconnect the DC

power cable.

w Unscrew the 4 bottom screws, then remove the bottom

cover from the transceiver in the direction of the arrow.

e Remove the front panel from the main body using a stan-

dard screw driver as shown below.

r Disconnect the ﬂat cable from the front panel.

t Unscrew the 4 rear plate screws, then remove the rear

plates from both the front panel and main body attach-

ments.

☞ Continue to the back page.

Rear plate

*This illustration

shows the descrip-

tion for the front

panel attachment.

Unscrew the cir-

cuit board screw.

Front panel

Flat cable Main body

Front panel

Flat cable

Main body

Front panel

Standard

screw driver

Bottom cover

CAUTION! To avoid damage to the transceiver, turn the

power OFF before separating the front panel from the

main body.

■ Supplied accessories

Main body attachment

Front panel attachment Flat cable

Mounting bracket Flat washers

(M5)

Spring washers

(M5)

Mounting screws

(M5 12)×

Self-tapping screws

(M5 16)×

Bracket screwsNuts (M5)

Icom, Icom Inc. and the logo are registered trademarks of Icom Incor-

porated (Japan) in the United States, the United Kingdom, Germany, France,

Spain, Russia and/or other countries.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6573H-1EX Printed in Japan

■ Mounting

2 types of mounting styles are available one is overhead—

mounting, and other one is on-board mounting.

Mount the front panel and the attachment securely with the

4 supplied screws to a thick surface which can support more

than 1.5 kg. (Overhead mounting)

On-board mounting

Overhead mounting

When using

self-tapping screws

Flat washer

Spring washer

Bracket

screw

Bracket screw

■ Attachment

For the front panel attachment:

q Connect the optional OPC-607, OPC-608 or OPC-609 to

the front panel attachment as shown below.

After the cable connection, replace the removed rear plate

and the 4 screws.

• The optional cable can be inserted into either the left or right

grooves as desired on the back of the attachment.

w Connect the ﬂat cable (q) as shown below, and then at-

tach the front panel and the attachment (w).

• ﬂ Ensure the at cable is inserted correctly, and not upside down.

For the main body attachment:

e Connect the optional OPC-607, OPC-608 or OPC-609 to

the main body attachment as shown below.

After the cable connection, replace the removed rear

plate.

• The optional cable can be inserted into either the left or right

grooves as desired on the back of the attachment.

r Connect the supplied ﬂat cable* and ground cable (coming

from the RMK-3) as shown below.

*Ensure the at cable and attachment are inserted/attached cor-ﬂ

rectly, and not upside down.

t Replace the removed bottom cover and 4 screws, then re-

connect the DC power cable.

Main body attachment

to transceiver s’

main body

Main body

Main body attachment*

Flat cable*

from the RMK-3

Use the attached screw

OPC-607/

OPC-608/

OPC-609

Rear plate

Main body attachment

Cable groove

Use the screw re-

moved from the cir-

cuit board in step t

on the front page, to

connect the cable lug.

Front panel

Front panel attachment

Flat cable

Attach the front

panel and attach-

ment securely.

OPC-607/

OPC-608/

OPC-609 Rear plate

Front panel attachment

Use the screw re-

moved from the cir-

cuit board in step t

on the front page, to

connect the cable lug.

Cable groove

Printed on recycled paper with soy ink.

Product specificaties

Merk:	Icom
Categorie:	Radio
Model:	RMK-3
Kleur van het product:	Zwart
Merkcompatibiliteit:	ICOM
Aantal:	1
Compatibiliteit:	IC-F5061, IC-6061
Type product:	Montagebeugel