I-PRO WV-X2571LN Handleiding

I-PRO Bewakingscamera WV-X2571LN

Lees hieronder de 📖 handleiding in het Nederlandse voor I-PRO WV-X2571LN (19 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/19

Model No. WV-X2571LN

Trademarks and registered trademarks

• Microsoft, Windows, Windows Media, Internet Explorer, Microsoft Edge, and ActiveX are either registered

trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• Intel and Intel Core are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.

• Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe in the United States and/or

other countries.

• SDXC Logo is a trademark of SD-3C, LLC.

• iPad and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.

• Android and Google Chrome are trademark of Google LLC.

• Firefox is a trademark of the Mozilla Foundation in the US and other countries.

• The word “QR Code” is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.

• All other trademarks identified herein are the property of their respective owners.

Troubleshooting

Before requesting service, refer to “Troubleshooting” of Basic Information and Operating Instructions. Then, confirm

the trouble.

Precautions for installation

 In order to prevent injury, the product must be securely mounted to a ceiling or wall according to

Installation Guide.

 Installation area for this product

Select an appropriate place for the installation area (such as a strong wall or ceiling) in your particular environment.

• Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.

• Install the camera in the foundation area of the architecture or where sufficient strength is assured.

• Do not mount the product on a plaster board or a wooden section because they are too weak. If the product is

unavoidably mounted on such a section, the section shall be sufficiently reinforced.

 Install the product in areas that do not receive direct sunlight.

When the product is installed outside in areas that receive direct sunlight, such as on external walls, use the optional

“WV-QSR500-W or WV-Q7118: Sun Shade”.

 Do not place this product in the following places

• Locations where a chemical agent is used such as a swimming pool

• Locations subject to moisture or oil smoke such as a kitchen

• Locations that have a specific environment that is subject to an inflammable atmosphere or solvents

• Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated

• Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot

springs, volcanic regions, etc.

• Locations where the temperature is not within the specified range

• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not

designed for on-vehicle use.)

• Locations subject to condensation as the result of severe changes in temperature

• Locations near rubber products (packing, rubber feet, etc.)

 Screw tightening

Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.

Specifications* *For further information, refer to the Basic Information.

: Direct current symbol

Open Source Software

• This product contains open source software licensed under GPL (GNU General Public License), LGPL (GNU

Lesser General Public License), etc.

• Customers can duplicate, distribute and modify the source code of the software under license of GPL and/or LGPL.

• For details concerning licensing and source code of open source software, click “Click here for OSS information”

on “Support” page of the setup menu of this product and read the displayed content.

• Please note that we shall not respond to any inquiries regarding the contents of the source code.

Except for open source software licensed under GPL/LGPL and so on, distributing, copying, disassembling, reverse

compiling and reverse engineering of the software provided with this product are all expressly prohibited. In addition,

exporting any software provided with this product violating export laws is prohibited.

Installation Guide

Included Installation Instructions

Network Camera

For professional use only

Outdoor use

 Do not insert any foreign objects.

Fire or electrical shock may be caused if water or any foreign objects, such as metal objects, enter inside the unit.

Turn the power off immediately and contact qualified service personnel for service.

 Do not use this product in an inflammable atmosphere.

Failure to observe this may cause an explosion resulting in injury.

 Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.

Otherwise, the mounting portions will deteriorate and injury or accidents due to a fall of the product may occur.

 Do not strike or give a strong shock to this product.

Failure to observe this may cause injury or fire.

 Keep SD memory cards away from infants and children.

Otherwise, they may swallow the cards by mistake.

In this case, consult a doctor immediately.

 Do not hang down from this product or use this product as a pedestal.

Failure to observe this may cause injury or accidents.

 Do not damage the power cable.

Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable. Do not place heavy objects on it,

and keep it away from heat sources.

Use of a damaged power cable may cause electric shock, short circuit, or fire.

Consult the dealer for repair.

 Do not install this product on a place that is greatly influenced by wind.

Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a fall of the product

resulting in injury or accidents.

 Do not sprinkle more water, exceeding the performance limit of waterproof with a high pressure

cleaning machine, etc.

Fire or electrical shock may be caused by immersion.

 Do not attempt to disassemble or modify this product.

Failure to observe this may cause fire or electric shock. Consult the dealer for the repair or inspections.

 Do not install or clean the camera, or touch this product, the power cable or the connected cables

during thunder storms.

Failure to observe this may cause electric shock.

 Refer installation work to the dealer.

Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or

damage to the product. Be sure to consult the dealer.

Power source *1: DC 12 V

PoE (IEEE802.3af compliant)

Power consumption *1: DC 12 V: 980 mA/Approx. 11.8 W

PoE DC 48 V: 260 mA/Approx. 12.5 W (Class 0 device)

Operating environment

Ambient operating temperature:

Ambient operating humidity:

–40 °C to +60 °C *2 {–40 °F to +140 °F}

(Power On range: –30 °C to +60 °C {–22 °F to +140 °F})

10 % to 100 % (no condensation)

Storage environment

Storage temperature:

Storage humidity:

–30 °C to +60 °C {–22 °F to +140 °F}

10 % to 95 % (no condensation)

Monitor output

(for adjustment):

VBS: 1.0 V [p-p]/75 Ω, composite, ø3.5 mm mini jack

An NTSC or PAL signal can be outputted from camera

(either press the INITIAL SET switch quickly (within 1 second) or use

software to select NTSC or PAL signal).

EXT I/O terminals: ALARM IN1

(Alarm input 1/ Black & white input/ Auto time adjustment input) (x1)

ALARM IN2 (Alarm input 2/ ALARM OUT) (x1)

ALARM IN3 (Alarm input 3/ AUX OUT) (x1)

Audio input:

For microphone input:

For line input:

ø3.5 mm stereo mini jack

Recommended applicable microphone: Plug-in power type

(Sensitivity of microphone: -48 dB±3 dB (0 dB=1 V/Pa, 1 kHz))

Input impedance: Approx. 2 kΩ (unbalanced)

Supply voltage: 2.5 V ±0.5 V

Input level: Approx. –10 dBV

Audio output *3:ø3.5 mm stereo mini jack (Audio output is monaural.)

Output impedance: Approx. 600 Ω (unbalanced)

Output level: –20 dBV

Waterproof *4: IP66 (IEC 60529), Type 4X (UL50E)

NEMA 4X compliant

Shock resistance: 50 J (IEC 60068-2-75 compliant), IK10 (IEC 62262)

Wind resistance: Up to 40 m/s {approx. 89 mph}

Dimensions: When using base bracket:

ø164 mm × 139 mm (H) {ø6-15/32 inches × 5-15/32 inches (H)}

Dome radius 42 mm {1-21/32 inches}

When using attachment plate only:

ø154 mm × 103 mm (H) {ø6-1/16 inches × 4-1/16 inches (H)}

Dome radius 42 mm {1-21/32 inches}

Mass: When using base bracket: Approx. 1.6 kg {3.53 lbs}

When using attachment plate only: Approx. 1.2 k {2.65 lbs}g

Finish: Main body: Aluminum die cast, i-PRO white

Outer fixing screws: Stainless steel (Corrosion-resistant treatment)

Dome cover: Polycarbonate resin (with ClearSight coating), Clear

Others: Tamper-resistant enclosure*5

*1 Refer to our support website <Control No.: C0106> for further information about Power source and Power

consumption information.

*2 When using with the IR LED light constantly lit, the upper limit of the operating temperature range is +50°C

{+122 °F}.

*3 This camera is not equipped with the function to change the audio output to the monitor output.

*4 Only when installation work is properly performed according to the Installation Guide and appropriate

waterproof treatment is performed.

*5 Component that has a structure on which the screws that are accessible after installation cannot be

screwed or unscrewed using an ordinary screwdriver.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

NOTE: This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equip-

ment generates, uses, and can radiate radio frequen-

cy energy and, if not installed and used in accor-

dance with the instruction manual, may cause harm-

ful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case the

user will be required to correct the interference at his

own expense.

FCC CAUTION: Changes or modifications not

expressly approved by the party responsible for com-

pliance could void the user’s authority to operate the

equipment.

Supplier’s Declaration of conformity

Trade name : i-PRO

Model No. : WV-X2571LN

Responsible Party :

i-PRO Americas Inc.

8550 Fallbrook Drive, Suite 200 Houston,

Texas 77064

Support Contact : 1-800-513-5417

For U.S.A.

CAN ICES-3(A)/NMB-3(A)

For Canada

The model number and serial number of this prod-

uct may be found on the surface of the unit.

You should note the model number and serial num-

ber of this unit in the space provided and retain this

book as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

For U.S.A.

This device complies with part 15 of FCC Rules and

Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions :

(1)This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

Le présent appareil est conforme à la partie 15 des

règles de la FCC et aux normes des CNR

d’Innovation, Sciences et Développement

économique Canada applicables aux appareils radio

exempts de licence.

L’exploitation est autorisée aux deux conditions sui-

vantes : (1) l’appareil ne doit pas produire de brouil-

lage, et (2) l’appareil doit accepter tout brouillage

subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

For U.S.A. and Canada

Optional accessories* 1

“<Control No.: C****>” used in these documents should be used to search for information

on our support website (https://i-pro.com/global/en/surveillance/training_support/support/

technical_information) and will guide you to the right information.

About the user manuals

Product documentation is composed of the following documents.

•

Installation Guide (this document): Provides information about “Precautions”,

“Precautions for installation” and the installation method.

• Basic Information (in the following website): Provides information about

“Precautions for use” and “Detail specifications”.

• Explains how to perform the Operating Instructions (in the following website):

settings and how to operate this camera.

https://i-pro.com/global/en/surveillance/documentation_database

Méthode

d’installation

Vis de

xation

recom-

mandée

La capacité de

traction minimale

requise

Quand la caméra

vidéo est directement

installée au plafond

ou sur le mur.

M4/ 4 él. 196 N {44 lbf}

• Before attempting to connect or operate this product, please read these instructions

carefully and save this manual for future use.

• SDXC/ SDHC/ SD memory card is described as SD memory card.

• The external appearance and other parts shown in this manual may differ from the actual product within the

scope that will not interfere with normal use due to improvement of the product.

For U.S. and Canada:

i-PRO Americas Inc.

https://www.i-pro.com/

For Europe and other countries:

i-PRO Co., Ltd. Fukuoka, Japan

https://www.i-pro.com/

i-PRO EMEA B.V. UK Branch

1010 Cambourne Business Park,

Cambridgeshire CB23 6DP

Authorised Representative in EU:

i-PRO EMEA B.V.

Laarderhoogtweg 25, 1101 EB

Amsterdam, Netherlands

Cs0920-2042

Printed in China

Caution:

• The DC power supply connected to the camera must

be in the same building.

• The network camera is only intended for a connection

to an ethernet or PoE network without routing to the

outside plant.

• This product has no power switch. Be sure to install

disconnect devices such as a circuit breaker to shut

down the main power of power supplying equipment

to this product.

• Only connect 12 V DC Class 2 power supply (UL

1310/CSA 223) or limited power source (IEC/EN/UL/

CSA 60950-1 or IEC/EN/UL/CSA 62368-1 Annex Q).

• Before attempting to connect or operate this

product, please read these instructions carefully.

Notice:

• This product is not suitable for use in locations where

children are likely to be present.

• Do not install this product in locations where ordinary

persons can easily reach.

• This product is a professional equipment.

• For information about screws and brackets required

for installation, refer to the corresponding section of

this document.

Precautions

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out

of improper installation or operation inconsistent with this

documentation.

Dome cover (Smoke type): WV-CW7S Ceiling mount bracket: WV-Q105A*

Dome cover

(Smoke type with ClearSight coating): WV-CW7SN

Sun shade (Light gray): WV-Q7118

Sun shade (i-PRO white): WV-QSR500-W

<i-PRO white*3> <Fine silver*3> <Light gray*3>

Ceiling mount bracket: WV-QEM500-W WV-Q169A –

Ceiling mount bracket: WV-QCL501-W WV-Q121B WV-Q178

Wall mount bracket: WV-QWL501-W WV-Q122A WV-Q185

Attachment pipe bracket: WV-QAT500-W WV-Q123A WV-Q179

Mount bracket: WV-QSR501-W WV-Q124 WV-Q186

Pole mount bracket: WV-QPL500-W WV-Q188 WV-Q182

Corner mount bracket: WV-QCN500-W WV-Q189 WV-Q183

Wall mount bracket: WV-QWL500-W – WV-QWL500-G

*1 Refer to our support website <Control No.: C0501> for further information about optional accessories.

*2 This product can only be installed indoors when WV-Q105A is used to install it on the ceiling.

*3 Refer to our support website <Control No.: C0112> for further information about combinations of each

bracket.

 Heater unit

This product is equipped with an internal heater unit for use in cold climates. The heater unit turns on automatically

when the temperature inside the product drops below around 0°C {32 °F}. When this product is installed and

operated in low temperatures below –20 °C {–4 °F}, it may require time to start up since the camera will wait to be

warmed up internally by the internal heater right after the power is turned on. Also, the camera may not function

properly, if it is installed and operated in an environment where the temperature is below –25 °C {–13 °F}. In such a

case, wait approximately 2 hours or more until the camera is warmed up. Then, turn on the power again.

As the camera warms up, snow or frost accumulated on the dome cover will melt. However, it may not be defrosted

from the cover depending on the ambient temperature or weather condition.

 About reflection of light from outside or IR light

A ghost may appear on the screen depending on the incident angle of external light.

In the case of using the IR light, installation of a camera near a wall may cause reflection of infrared rays resulting in

a part of the screen or the entire screen turning whitish.

• Refer to our support website <Control No.: C0109> for image examples and measures to take.

 Take notice of humidity

Install this product when the humidity is low. If installation is performed when it is raining or in very humid conditions,

the inside may be affected by humidity, causing mist-over inside the dome cover.

 Protection from lightning

When cables are used outdoors, there is a chance that they may be affected by lightning. In such a case, install a

lightning arrestor close to the camera, and make the length of the network cable between the camera and lightning

arrestor as short as possible to prevent the camera from being affected by lightning.

 When noise disturbance may happen

Noise may appear in video or audio near a strong electric field from a TV or radio antenna, motors and transformers,

or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more. Conduct the power

distribution work to keep 1 m {3-15/16 inches} away from them or conduct the electric conduit work using metal

pipes. (Be sure to make ground connection of the metal pipes.)

 Make sure to remove this product if it will no longer be used.

 This product has no power switch.

When turning off the power, disconnect the power supply from the 12 V DC power supply or the PoE device.

 About the battery

A battery is installed inside the camera. Do not leave the battery exposed in environments of excessive heat as a

result of sunlight or fire.

 Equipment classification and power source indication label

Refer to the indication label on the bottom side of this unit for the equipment classification, power source, and other

information.

 Stop the operation immediately when something is wrong with this product.

When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product

has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or damage to the product.

In this case, turn the power off immediately and contact qualified service personnel for service.

 Select an installation area that can support the total weight.

Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or

accidents. Installation work shall be started after sufficient reinforcement.

 Periodic inspections shall be conducted.

Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.

Consult the dealer for the inspections.

 The exclusively designed mount bracket shall be used.

Failure to observe this may cause a drop resulting in injury or accidents.

Use the exclusively designed mount bracket for installation.

 The screws and bolts must be tightened to the specified torque.

Failure to observe this may cause a drop resulting in injury or accidents.

 Turn the power off when do wiring of this product.

Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may cause fire.

 Install this product in a location high enough to avoid people and objects from bumping the product.

Failure to observe this may cause injury.

 Do not install this product in locations subject to vibration.

Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.

 Correctly perform all wiring.

Short circuits in the wiring or incorrect wiring may cause fire or electrical shock.

 Install the product securely on a wall or a ceiling in accordance with the installation instructions.

Failure to observe this may cause injury or accidents.

 Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

 Do not touch the metal part of the bottom side of the product.

The metal part of the bottom side may become hot while the product is in use. Direct skin contact with high-

temperature parts of the product may cause burns.

 Turn the power off when cleaning this product.

Failure to observe this may cause injury.

Standard accessories

*1 This label may be required for network management. Use caution not to lose this label.

Other items that are needed (not included)

• Fixing screw

Installation Guide (this document) 1 pc. .....................

IMPORTANT SAFETY INSTRUCTIONS 1 pc. .............

Code label*1 ..................................................... 1 pc.

The following parts are used during installation procedures.

Base bracket .................................................... 1 pc.

Attachment plate .............................................. 1 pc.

Fixing screw for attachment plate

(M4 × 8 mm {5/16 inches}) ............................. 5 pcs.

(of them, 1 for spare)

RJ45 waterproof connector cover 1 pc. ....................

RJ45 waterproof connector cap 1 pc. .......................

Bit (Hex wrench, screw

size 6.35 mm {1/4 inches} T20) 1 pc. ........................

Template A (for the attachment plate) 1 sheet .............

Template B (for the base bracket) 1 sheet ..................

Waterproof tape 1 pc. ................................................

4P alarm cable 1 pc. .................................................

2P power cable 1 pc. ................................................

MONITOR OUT conversion plug 1 pc. .......................

Rain wash coating label 1 pc. ....................................

Installation method

Recommended

screw*1

Minimum pull-out

strength*2

: Mount the camera on the two-gang junction box

using the attachment plate

M4/ 4 pcs. 196 N {44 lbf}

: Directly mount the camera onto the ceiling or wall

using the attachment plate

Mount the camera onto the ceiling or wall using the

base bracket

Mount the camera using the exclusively designed mount bracket.

Refer to the operating instructions

of each bracket.

*1 Select screws according to the material of the location that the camera will be mounted to. In this case,

wood screws and nails should not be used.

For information about the minimum pull-out strength, refer to our support website <Control No.: C0120>.

• RJ45plug, Ethernet cable (category 5e or better, straight, all 4 pairs (8 pins))

• As necessary, audio input cable, audio output cable, alarm I/O cables, power supply cable

• Tools

Junction box

Directly mount

Base bracket

Parts and functions

Attachment plate

(accessory)

Azimuth adjustment ring

Dome cover

Enclosure

TILT table

PAN table

Camera

Fixing screw for attachment

plate (accessory)

Camera fixing

screw

Conduit wiring

connector

Base bracket

(accessory)

Direction marker for installation (TOP )

• Points up when installing to

a wall.

PAN table fixing

screw

Direction marker

for installation

(FRONT )

• FRONT must positioned

in front of the camera (on

the i-PRO logo side).

Waterproof rubber

Screen display

top (TOP)

SD slot

SD memory card

warning

/error indicator

MONITOR OUT

terminal

(factory shipment:

NTSC monitor)

Dehumidifying

device

 Indicators

Note:

• Lighting/blinking LED can be turned off with the software settings at any time. (The initial state is lighting or blinking.)

Refer to the Operating instructions for information about settings.

LINK indicator

When the camera is able to communicate with the connected device Lights orange

ACT indicator

When data is being sent via the network camera Blinks green (accessing)

SD (MOUNT) indicator

When an SD memory card is inserted and could be recognized Lights off Blinks green →

→ Lights off

When data can be saved after the SD memory card is inserted and the SD ON/OFF

button is pressed (less than 1 second)

Lights off Lights green→

When data can be saved to the SD memory card Lights green

When the SD memory card is removed after holding down

the SD ON/OFF button (about 2 seconds)

(recording) Lights green →

Blinks green Lights off→

(waiting for recording) Lights green Lights off→

When data cannot be saved to the SD memory card because an abnormality was

detected or the SD memory card is configured not to be used

Lights off

SD ERROR/AF indicator

When AF (Auto Focus) operation is being executed Blinks red (Interval of

1 time/ second)

When the network camera is being started Lights red

When an SD memory card is recognized normally Lights red Lights off→

When the SD slot is not used or an abnormality is detected in SD memory card after

the camera has started

Lights red Stays red→

SD memory card warning/error indicator (off in the initial state)

When a warning status is detected

(SD memory card warning detection conditions: After the total use time has

exceeded 6 years and the number of overwrite times has exceeded 2000)

Lights red

When an error status is detected

(SD memory card error detection conditions: Write error, read error, etc.)

Blinks red

 Buttons

• INITIAL SET button (Initializing / NTSC PAL switch button)

Follow the steps below to initialize the network camera. Retry if the camera does not start up normally.

When the INITIAL SET button is pressed (less than 1 second), the MONITOR OUT terminal can be switched for

the NTSC monitor PAL monitor. The monitor out is set to NTSC in the default settings of the camera.

Turn off the

power of

the camera

Turn on the power of the

camera while pressing

the INITIAL SET button*

15 seconds Make sure

to release

the button

around

2 minutes

The camera will start up

and the settings including

the network settings will

be initialized

  

* Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and

may cause malfunction.

• SD ON/OFF button

• When the SD ON/OFF button is pressed (less than 1 second), the SD (MOUNT) indicator lights up in green and data

can be saved to the SD memory card.

• When the SD ON/OFF button is held down (about 2 seconds), the SD (MOUNT) indicator lights off and the SD

memory card can be removed.

• AF button Press the AF button to automatically adjust the focus.

• TELE button Press the TELE button to adjust the zoom ratio to the “Tele” side.

• WIDE button Press the WIDE button to adjust the zoom ratio to the “Wide” side.

Step2 Making connections

IMPORTANT:

• Devices to which power can be supplied to this product are PoE hub, PoE power supplying equipment,

and external 12 V DC power supply.

• Turn off each system’s power supply before making a connection.

RJ45 Network cable

Ethernet cable

(category 5e or better,

straight, 4 pairs (8 pins))

RJ45

waterproof jack

Less than 100 m {328 feet}

External dimension:

ø5 mm {ø3/16 inches} -

ø6.5 mm {ø1/4 inches}

EXT I/O cable

4P alarm cable

(accessory)

2P power cable (accessory)

Power

supply cable

12 V DC (Red)

GND (Black)

Audio input

cable (white)

Audio output

cable (black)

Microphone or

external audio line

Built-in amplifier

External speaker

GND (Black)

ALARM IN3 (Gray)

ALARM IN2 (Red)

ALARM IN1 (Green)

Less than 10 m {32.8 feet}

(for microphone input)

Less than 1 m {3.28 feet}

(for line input)

Less than 10 m {32.8 feet}

RJ45

waterproof

connector

cover

(accessory)

RJ45 waterproof

connector cap

(accessory)

RJ45 plug

(locally

procured)

 How to connect a RJ45 waterproof connector

Wire and caulk

Tighten until no

gap is present

Align “



” with “



” and then

rotate until “



” aligns with “”.

Insert the RJ45 plug

IMPORTANT:

• When removing the RJ45 waterproof connector, be sure

to remove it with the reverse procedure of connection.

• When connecting both the 12 V DC power supply and

the PoE device for power supply, 12 V DC will be used

for power supply.

• When the Ethernet cable is disconnected once,

reconnect the cable after around 2 seconds. When the

cable is quickly reconnected, the power may not be

supplied from the PoE device.

 Waterproof treatment for external I/O cables,

power supply cables, audio input cables, and

audio output cables

IMPORTANT:

• Stretch the waterproof tape (accessory) by approx.

twice its length and wind it tightly around the cable.

• At the start and end winding points, make the tape

overlaps the external covering parts by approx.

20mm {25/32 inches}.

• For the above 4 types of cables, even if they are not

used, waterproofing treatment must be performed on

the connector parts.

Approx. 20 mm

{25/32 inches}

Approx. 20 mm

{25/32 inches}

• Install the connector and cable connection parts in locations where they aren’t regularly exposed

to rain or water.

Step3 Mount the camera

{ }1 Align the OPEN mark of the side

of the camera with the protruding

part of the base bracket, insert the

attachment mounting screws (2

places) into the attachment plate,

rotate the camera by approx. 15°

and temporarily fix it.

• When directly attaching the attachment plate to a

ceiling or wall, align the OPEN mark to the nail of

the attachment plate.

IMPORTANT:

• When mounting to a wall, mount so that cable

outlet of the camera faces up.

• For installation on the wall, install the camera

with the dehumidifying device in a sideways or

downward position. In a face-up position, the

dehumidifying device doesn’t work well as water

accumulates on the surface.

OPEN mark

Position of

dehumidifying

device

Cable outlet of

the camera

Holes of the

attachment plate

(4 places)

Protruding part of base bracket

(Nail of the attachment plate)

Attachment

mounting screw

Protruding part

of base bracket

{ }2

Loosen enclosure fixing screws (4 places)

using the bit (accessory), and remove the

enclosure from the camera.

IMPORTANT:

• Enclosure is fixed to the camera body by the

installed auxiliary wire, so please do not remove it.

{ }3 Secure the camera by tightening the

camera fixing screw (red).

Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

{ }4 Connect the MONITOR OUT

conversion plug (accessory) to the

MONITOR OUT terminal of the camera,

and then connect the monitor for

adjustment with a pin cable (locally

procured).

{ }5 If necessary, insert an SD memory card

by referring to “Insert / remove an SD

memory card”. Bit (accessory) Enclosure fixing

screw (4 places)

Installed

auxiliary

wire

Camera fixing

screw (red)

Step4 Adjustment

{ }1 Turn on the power for the camera and remove the protection film from the

lens.

{ }2 Adjust the camera direction.

1 Loosen the PAN table fixing screw with

washer and the cross-head side of TILT table

fixing screw (on one side).

2Adjust the angle of the camera while

watching the adjustment monitor.

Horizontal (PAN) angle: ±180°

Vertical (TILT) angle: -30° to +85°

Azimuth(YAW) angle: ±100°

Note:

• When mounting the camera on a wall,

adjust after rotating the PAN table by 180°

to the left.

• When using the camera at a vertical

position where the camera lens is nearly

horizontal, part of the image may appear

to be overlapped, part of the camera

may be visible, and reflection from IR rays

may appear on the screen when viewing

images at night. To prevent this, decrease

the vertical position angle or adjust the

zoom ratio.

3 Fix the camera unit by tightening the cross-

head side of TILT table fixing screw (on one

side) and the PAN table fixing screw with

washer.

Recommended tightening torque: 0.59 N·m

{0.44lbf·ft}

IR light

(IR LED: 2 places)

Azimuth adjustment ring

TILT table

Azimuth (YAW)

angle

PAN table fixing screw with

washer

Vertical (TILT)

angle

Installed

auxiliary

wire

PAN table

TOP mark

TILT table fixing

screw

Horizontal

(PAN) angle

{ }3 Adjust the zoom and focus.

• While watching the screen, adjust the zoom ratio using the TELE

button and the WIDE button and adjust the focus by pressing

the AF (auto focus) button.

• Readjust the angle of the camera with the PAN table, TILT table,

and azimuth adjustment ring if necessary.

Note:

• When the resolution is set to higher than 1280×720, image

quality may deteriorate depending on the zoom ratio. Refer

to our support website <Control No.: C0124> for further

information.

TELE button

WIDE button AF button

Enclosure

Enclosure fixing screw

(4 places)

Waterproof

rubber

LOCK mark

mark

Camera

unit

Bit

(accessory)

Dome cover

{ }4 Disconnect the MONITOR OUT conversion

plug (accessory). Attach the enclosure and

secure it by using a bit (accessory) to tighten

the enclosure fixing screws (4 places).

Attach the enclosure by aligning the LOCK mark to the ▼

mark on the camera body.

Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

IMPORTANT:

• Make sure that the waterproof rubber is not detached

from the groove.

{ }5

After complete installation, remove the

protection film from the dome cover and

attach the rain wash coating label (accessory)

to the external part, etc. of the camera.

{ }6 Connect to the network by following information described on our support

website <Control No.: 0123>.

{ }7 Refer to the Operating Instructions and perform the auto focus function from

the setup menu.

Insert / remove an SD memory card

 Insert an SD memory card

1Remove the enclosure from the camera.

2 Insert the SD memory card into the end of the SD

slot and confirm that a clicking sound is made.

3 Take your finger off the SD memory card and check

that the back end of SD memory card does not

protrude over the upper part of the SD guide rib.

4After the SD memory card has been inserted,

press the SD ON/OFF button, and make sure the

SD (MOUNT) indicator is continually lit. (If you do

not press the SD ON/OFF button after inserting

the SD memory card, the SD (MOUNT) indicator

is automatically lit approximately 5 minutes later.)

5Attach the enclosure to its original position.

Back end of the

SD memory card

(with the label side

facing the lens side)

SD guide rib

SD ON/OFF button

SD (MOUNT) indicator

 Remove an SD memory card

When removing an SD memory card, reverse the procedure for inserting an SD memory card.

Press and hold the SD ON/OFF button for approx. 2 seconds, and then remove the SD memory card after

checking that the SD (MOUNT) indicator has changed from blinking to off.

IMPORTANT:

• Before turning off the camera power switch, make sure that the SD (MOUNT) indicator is turned off.

Note:

• When using an SD memory card, format it using this product. Refer to the Operating Instructions for how to

format an SD memory card.

• Use compatible SD memory cards. Refer to our support website <Control No.: C0107> for latest information

about the compatible SD memory cards.

Step1 Processing the installation surface (process according to the installation type)

Common

• Attach the attachment plate (accessory) so that the marking (part

number) faces toward the ceiling or wall to be installed.

• If open wiring is conducted, be sure to use conduits and run the

cables inside the tubes to protect the cables from direct sunlight.

IMPORTANT:

• Installation work shall be such that there is no exposure to water

into the architecture through the conduits having been joined.

Two-gang

junction box

Attachment plate

(accessory)

Fixing screw

(4 pcs.)

(M4: locally procured)

46 mm

{1-13/16 inches}

83.5 mm

{3-9/32 inches}

Junction box

{ }1 Install the junction box on the installation

surface.

{ }2 Mount the attachment plate to the junction box.

Directly mount

{ }1 Drill a hole in the installation surface

using template A (accessory).

(4 screw holes / 1 cable access hole)

Note:

• When installing on a wall, make a hole so as

to face the TOP mark of the template to the

upper side.

• When installing on a ceiling, make a hole so as

to face the FRONT mark of the template to

the front side of the camera (in the direction of

i-PRO logo).

• If you want to be able to change the direction

of the camera after installation, drill through

a 73mm {2-7/8 inches} diameter hole in

the center. By doing so you can adjust the

mounting direction of the camera in 90°

increments.

4×M4

Cable access hole

ø {ø2-7/8 inches}73 mm

Cable access hole

ø {ø1 inch}25.4 mm

{ }2 Install the attachment plate on the installation surface.

Attachment plate

(accessory)

Fixing screw (4 pcs.)

(M4: locally procured)

Base bracket

{ }1

Make a hole on the installation surface using template B (accessory). (Screw holes

(M4:4 places) / Cable access hole (1 place))

No cable access hole is needed when using conduit

•

Depending on the condition of the ceiling or the wall surface,

six patterns of screw positions are available for fixation. Select

a pattern from the following table and make holes.

Vertical Horizontal

A85 mm {3-11/32 inches}

(85.7 mm {3-3/8 inches})

85 mm {3-11/32 inches}

(85.7 mm {3-3/8 inches})

B138 mm {5-7/16 inches} 138 mm {5-7/16 inches}

C83.5 mm {3-9/32 inches} 46 mm {1-13/16 inches}

D63 mm {2-15/32 inches} 63 mm {2-15/32 inches}

E* – 83.5 mm {3-9/32 inches}

F70 mm {2-3/4 inches} 108.5 mm {4-9/32 inches}

* When mounting to a single-gang junction box, fix it with

screws (2 pcs.) (M4: locally procured).

• Select either of the two cable access holes of template B

to proceed with the installation work.

• After mounting the attachment plate, the mounting

direction of the camera can be adjusted in 90° increments.

Base bracket

Remove the cap for the female

thread for the conduit using a

5mm {3/16 inches} hexagon

wrench and attach the conduit.

{ }2 Install the base bracket on the

installation surface.

{ }3 Mount the attachment plate

onto the base bracket.

Conduit

Cap for the

female thread

for the conduit

Base bracket

Fixing screw (4 pcs.)

(M4: locally procured)

Minimum pull-out

strength: 196 N

{44.06 lbf} (per 1 pc.)

Attachment plate

(accessory)

Fixing screw for attachment plate (4 pcs.)

(M4×8 mm {5/16 inches}: accessory)

Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}

The female thread for conduit is compliant

with ANSI NPSM (parallel pipe threads) 3/4

or ISO 228-1 (parallel pipe threads) G3/4.

When using a conduit

Conduit fixing

position

Cable access hole

ø25.4 mm

{ø1 inch}

Cable access hole

ø25.4 mm {ø1 inch}

51 mm

{2 inch}

51 mm

{2 inch}

Product specificaties

Merk:	I-PRO
Categorie:	Bewakingscamera
Model:	WV-X2571LN
Kleur van het product:	Wit
Soort:	IP-beveiligingscamera
Materiaal behuizing:	Aluminium, Polycarbonate (PC)
Internationale veiligheidscode (IP):	IP66
Ondersteunde mobiele besturingssystemen:	Android, iOS
Bluetooth:	Nee
Maximale capaciteit van de geheugenkaart:	256 GB
Ondersteund audioformaat:	AAC-LC, ADPCM, G.711, G.726
Ondersteunde videoformaten:	H.264, H.265, M-JPEG
Vormfactor:	Dome
Automatisch scherpstellen:	Ja
Ondersteuning voor plaatsing:	Binnen & buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond
Maximum resolutie:	3840 x 2160 Pixels
Totaal aantal megapixels:	- MP
Type stroombron:	DC, PoE
Stroomuitvoer (volt):	12, 48
Minimale belichting:	0.09 Lux
Aantal cameras:	1
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	SD, SDHC, SDXC
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Video bewegings-detectie:	Ja
Microfoon, line-in ingang:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Focus:	Gemotoriseerd
Brandpuntbereik:	4.3 - 8.6 mm
Vermogensverbruik (max):	11.8 W
Omvang optische sensor:	1/1.8 "
Type beeldsensor:	CMOS
Optische zoom:	2 x
Camera sluitertijd:	1/10000 s
Witbalans:	ATW, AWC
Ondersteunde grafische resoluties:	320 x 180,640 x 360,1280 x 720 (HD 720),1920 x 1080 (HD 1080),2560 x 1440
Ruisonderdrukking:	Ja
Netwerkstandaard:	IEEE 802.3af
Aantal gebruikers:	14 gebruiker(s)
Veiligheidsfunties:	Schokbestendig
Maximaal 30 frames per seconde:	30 fps
Ondersteunde netwerkprotocollen:	IPv6 : TCP/IP, UDP/IP, HTTP, HTTPS, FTP, SMTP, DNS, NTP, SNMP, DHCPv6, RTP, MLD, ICMP, ARP, IEEE 802.1X, DiffServ IPv4 : TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARP, IEEE 802.1X, DiffServ
Stroomverbruik:	980 mA
IK code:	IK10
Dag/nacht modus:	Ja
Achtergrondverlichting compensatie:	Ja
Detectieafstand (groothoek):	63.31 m
Detectieafstand (tele):	157.46 m
Observatieafstand (groothoek):	25.32 m
Observatieafstand (tele):	62.99 m
Herkenningsafstand (groothoek):	12.66 m
Herkenningsafstand (tele):	31.49 m
Identificatieafstand (groothoek):	6.33 m
Identificatieafstand (tele):	15.75 m
Highlight Compensation (HLC) (compensatie voor sterke belichting):	Ja
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 100 procent
Kijkhoek lens, horizontaal:	0 - 180 °
Kijkhoek lens, verticaal:	-30 - 85 °
Dynamisch bereik:	132 dB