I-PRO WV-U21300-V2L Handleiding

I-PRO Bewakingscamera WV-U21300-V2L

Lees hieronder de πŸ“– handleiding in het Nederlandse voor I-PRO WV-U21300-V2L (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Model No. WV-U2142LA
WV-U2132LA
WV-U21300-V2L
avs0821-3053
Printed in China
β€’ Before attempting to connect or operate this product, please read these instructions
carefully and save this manual for future use.
β€’ microSDXC/ microSDHC/ microSD memory card is described as microSD memory card.
β€’ The external appearance and other parts shown in this manual may differ from the actual product within the
scope that will not interfere with normal use due to improvement of the product.
Trademarks and registered trademarks
β€’ Microsoft, Windows, Windows Media, Internet Explorer, Microsoft Edge, and ActiveX are either registered trade-
marks or trademarks of Microsoft Corporation in the United States and/or other countries.
β€’ Intel and Intel Core are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
β€’ Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe in the United States and/or
other countries.
β€’ microSDXC Logo is a trademark of SD-3C, LLC.
β€’ iPad and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
β€’ Android and Google Chrome are trademark of Google LLC.
β€’ Firefox is a trademark of the Mozilla Foundation in the US and other countries.
β€’ The word "QR Code" is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.
β€’ All other trademarks identified herein are the property of their respective owners.
Troubleshooting
Before requesting service, refer to β€œTroubleshooting” of β€œBasic Information” and β€œOperating Instructions”. Then,
confirm the trouble.
Precautions for installation
β– ξ˜In order to prevent injury, the product must be securely mounted to an installation surface according
to Installation Guide.
β– ξ˜Installation area for this product
Select an appropriate place for the installation area (such as a strong wall or ceiling) in your particular environment.
β€’ Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.
β€’ Install the camera in the foundation area of the architecture or where sufficient strength is assured.
β€’ Do not mount the product on a plaster board or a wooden section because they are too weak. If the product is
unavoidably mounted on such a section, the section shall be sufficiently reinforced.
β– ξ˜This camera is designed to be used indoors
This product is not operable outdoors. Do not expose this camera to direct sunlight for hours and do not install the
product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction.
Keep this camera away from water and moisture.
β– ξ˜Do not place this product in the following places
β€’ Locations where a chemical agent is used such as a swimming pool
β€’ Locations subject to moisture or oil smoke such as a kitchen
β€’ Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
β€’ Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
β€’ Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot
springs, volcanic regions, etc.
β€’ Locations where the temperature is not within the specified range
β€’ Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not
designed for on-vehicle use.)
β€’ Locations where it may get directly wet from rain or water splash (including under the eaves, etc.)
β€’ Locations subject to moisture or dust
β€’ Locations subject to sudden changes in temperature such as near air discharge vents of air conditioners or air cir-
culation inlet doors
β€’ Locations near rubber products (packing, rubber feet, etc.)
β– ξ˜Screw tightening
Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.
β– ξ˜About reflection of light from outside or IR light
A ghost may appear on the screen depending on the incident angle of external light.
In the case of using the IR light, installation of a camera near a wall may cause reflection of infrared rays resulting in
a part of the screen or the entire screen turning whitish.
β€’ Refer to our support website <Control No.: C0109> for image examples and measures to take.
β– ξ˜Take notice of humidity
Install this product when the humidity is low. If installation is performed when it is raining or in very humid conditions,
the inside may be affected by humidity, causing mist-over inside the dome cover.
β– ξ˜Protection from lightning
When the cables brought from outdoors are used, there is a chance that they may be affected by lightning. In such a
case, install a lightning arrestor close to the camera, and make the length of the network cable between the camera
and lightning arrestor as short as possible to prevent the camera from being affected by lightning.
β– ξ˜When noise disturbance may happen
Noise may appear in video or audio near a strong electric field from a TV or radio antenna, motors and transformers,
or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more. Conduct the power distri-
bution work to keep 1 m {3.28 feet} away from them or conduct the electric conduit work using metal pipes. (Be
sure to make ground connection of the metal pipes.)
β– ξ˜Make sure to remove this product if it will no longer be used.
β– ξ˜This product has no power switch.
When turning off the power, disconnect the power supply from the PoE device.
β– ξ˜About the battery
A battery is installed inside the camera. Do not leave the battery exposed in environments of excessive heat as a
result of sunlight or fire.
β– ξ˜Equipment classification and power source indication label
Refer to the indication label on the bottom side of this unit for the equipment classification, power source, and other
information.
Specifications* *For further information, refer to the Basic Information.
: Direct current symbol
Open Source Software
β€’ This product contains open source software licensed under GPL (GNU General Public License), LGPL (GNU
Lesser General Public License), etc.
β€’ Customers can duplicate, distribute and modify the source code of the software under license of GPL and/or LGPL.
β€’ For details concerning licensing and source code of open source software, click β€œClick here for OSS information” on
β€œSupport” page of the setup menu of this product and read the displayed content.
β€’ Please note that we shall not respond to any inquiries regarding the contents of the source code.
Copyright
Except for open source software licensed under GPL/LGPL and so on, distributing, copying, disassembling, reverse
compiling and reverse engineering of the software provided with this product are all expressly prohibited. In addition,
exporting any software provided with this product violating export laws is prohibited.
Installation Guide
Included Installation Instructions
Network Camera
For professional use only
Indoor use
β–  Do not insert any foreign objects.
Fire or electrical shock may be caused if water or any foreign objects, such as metal objects, enter inside the unit.
Turn the power off immediately and contact qualified service personnel for service.
β–  Do not use this product in an inflammable atmosphere.
Failure to observe this may cause an explosion resulting in injury.
β–  Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and injury or accidents due to a fall of the product may occur.
β–  Do not strike or give a strong shock to this product.
Failure to observe this may cause injury or fire.
β–  Keep microSD memory cards away from infants and children.
Otherwise, they may swallow the cards by mistake.
In this case, consult a doctor immediately.
β–  Do not hang down from this product or use this product as a pedestal.
Failure to observe this may cause injury or accidents.
β–  Do not attempt to disassemble or modify this product.
Failure to observe this may cause fire or electric shock. Consult the dealer for the repair or inspections.
β–  Do not install or clean the camera, or touch this product, the power cable or the connected cables
during thunder storms.
Failure to observe this may cause electric shock.
β–  Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or
damage to the product.
Be sure to consult the dealer.
β–  Stop the operation immediately when something is wrong with this product.
When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product
has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or damage to the product.
In this case, turn the power off immediately and contact qualified service personnel for service.
β–  Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or
accidents. Installation work shall be started after sufficient reinforcement.
β–  Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
β–  The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
β–  Turn the power off when do wiring of this product.
Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may cause fire.
β–  Install this product in a location high enough to avoid people and objects from bumping the product.
Failure to observe this may cause injury.
β–  Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.
β–  Install the product securely on an installation surface in accordance with the installation instructions.
Failure to observe this may cause injury or accidents.
β–  Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
β–  Do not touch the metal part of the bottom side of the product.
The metal part of the bottom side may become hot while the product is in use. Direct skin contact with high-temper-
ature parts of the product may cause burns.
β–  Turn the power off when cleaning this product.
Failure to observe this may cause injury.
Precautions
Power source *1: PoE (IEEE802.3af compliant)
Power consumption *1:PoE DC 48 V : 135 mA/ Approx. 6.5 W (Class 0 device)
U2142
PoE DC 48 V : 120 mA/ Approx. 5.8 W (Class 2 device)
U2132
Operating environment
Ambient operating temperature:
Ambient operating humidity:
–10 Β°C to +50 Β°C {14 Β°F to 122 Β°F}
(Power On range: 0 Β°C to 50 Β°C {32 Β°F to 122 Β°F})
10 % to 90 % (no condensation)
Storage environment
Storage temperature:
Storage humidity:
–30 Β°C to +60 Β°C {–22 Β°F to +140 Β°F}
10 % to 95 % (no condensation)
Built-in microphone
<WV-U21300-V2L>
Nondirectional electret condenser microphone
Dimensions: ΓΈ129.5 mm Γ— 101 mm (H) {ΓΈ5-3/32 inches Γ— 3-31/32 inches (H)}
Dome radius 40 mm {1-9/16 inches}
Mass: Approx. 350 {0.77 lbs}g
Finish:
Main body
: ABS resin, i-PRO white
Dome cover
:
Acrylic resin, Clear
*1 Refer to our support website <Control No.: C0106> for further information about Power source and
Power consumption information.
Caution:
β€’ The network camera is only intended for a connec-
tion to an ethernet or PoE network without routing to
the outside plant.
β€’ This product has no power switch. Be sure to install
disconnect devices such as a circuit breaker to shut
down the main power of power supplying equipment
to this product.
β€’ Before attempting to connect or operate this product,
please read these instructions carefully.
Notice:
β€’ This product is not suitable for use in locations where
children are likely to be present.
β€’ Do not install this product in locations where ordinary
persons can easily reach.
β€’ This product is a professional equipment.
β€’ For information about screws and other parts
required for installation, refer to the corresponding
section of this document.
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment.
For more information about collection and recycling, please contact your local authority.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
About notations
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This equip-
ment generates, uses, and can radiate radio frequen-
cy energy and, if not installed and used in accor-
dance with the instruction manual, may cause harm-
ful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
FCC CAUTION: Changes or modifications not
expressly approved by the party responsible for com-
pliance could void the user's authority to operate the
equipment.
Supplier’s Declaration of conformity
Trade name : i-PRO
Model No. : WV-U2142LA,
WV-U2132L A, WV-U21300-V2L
Responsible Party :
i-PRO Americas Inc.
8550 Fallbrook Drive, Suite 200 Houston,
Texas 77064
Support Contact : 1-800-513-5417
For U.S.A.
CAN ICES-3(A)/NMB-3(A)
For Canada
The model number and serial number of this prod-
uct may be found on the surface of the unit.
You should note the model number and serial num-
ber of this unit in the space provided and retain this
book as a permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
For U.S.A.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions :
(1)This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
For U.S.A.
Standard accessories
*1 This label may be required for network management. Use caution not to lose this label.
Other items that are needed (not included)
β€’ Mounting screw
Optional accessories*1
Ceiling Mount Bracket: WV-Q105A
Dome Cover (Smoke type) *2: WV-CF5SA
Ceiling Mount Bracket *3: WV-QEM100
*1 Refer to our support website <Control No.: C0501> for further information about optional accessories.
*2 Refer to the installation method described in β€œHow to replace the dome cover” (leaflet) included in the
package of this product.
*3 When using WV-QEM100 camera ceiling mount bracket, if the built-in microphone hole is blocked by the
cover of bracket, the collectable volume may decrease and the sound of attic is likely to be collected by mis-
take. Therefore, please confi rm the installation conditions before use. <WV-U21300-V2L>
β€’RJ45plug, Ethernet cable (category 5e or better, straight, 4 pairs (8 pins))
β€’ Tools
Installation Guide (this document) ..................... 1 pc.
IMPORTANT SAFETY INSTRUCTIONS ............. 1 pc.
<WV-U2142LA><WV-U2132LA>
Code label*1...................................................... 1 pc.
The following parts are used during installation procedures.
Template ........................................................... 1 pc.
<WV-U2142LA><WV-U2132LA>
Dome cover sheet*2 .......................................... 1 pc.
PAN table fixing screw ...................................... 1 pc.
Indoor use
"<Control No.: C****>" used in these documents should be used to search for information
on our support website (https://i-pro.com/global/en/surveillance/training-support/support/
technical-information) and will guide you to the right information.
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
U2142
The functions with this notation are available when using the model WV-U2142LA (4M pixel model).
U2132
The functions with this notation are available when using the model WV-U2132LA, WV-U21300-V2L
(2M pixel model).
Installation method
Recommended
screw*1 Minimum pull-
out strength*2
Directly mount the camera onto the ceiling or wall. M4 x 16 mm*3 {5/8 inches}/ 2pcs. 196 N {44 lbf}
Mount the camera using the exclusively designed
mount bracket (See β€œOptional accessories”). Refer to each instruction guide of the bracket.
*1 Select screws according to the material of the location that the camera will be mounted to. In this case,
wood screws and nails should not be used.
*2 This value indicates the minimum pull-out strength required value per screw.
For information about the
minimum pull-out strength, refer to our support website <Control No.: C0120>.
*3 The screw length is an example when installing the camera on a robust ceiling or wall with a thickness
of 20 mm {25/32 inches} or more.
WV-U2142LA
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out
of improper installation or operation inconsistent with this
documentation.
*2 When replacing the dome cover, use the dome cover sheet provided with the camera.
MΓ©thode
d’installation
Vis de fixation
recommandΓ©e
La capacitΓ© de
traction minimale
requise
Quand la camΓ©ra
vidΓ©o est directement
installΓ©e au plafond
ou sur le mur.
M4 x 16 mm
{5/8 pouces}
/ 2 Γ©l.
196 N {44 lbf}
* La longueur de la vis est un exemple lors de l’installation
de la camΓ©ra au plafond ou sur un mur robuste d’une
Γ©paisseur de 20 mm {25/32 pouces} ou plus.
Β© i-PRO Co., Ltd. 2023
Indoor use
About the user manuals
Product documentation is composed of the following documents.
β€’ Installation Guide (this document): Provides information about β€œPrecautions”,
β€œPrecautions for installation” and the installation method.
β€’ 
Basic Information (Refer to the link on the following product information website):
Provides information about β€œPrecautions for use” and β€œDetail specifications”.
β€’ 
Operating Instructions (Refer to the link on the following product information website):
Explains how to perform the settings and how to operate this camera.
https://i-pro.com/global/en/surveillance/training-support/documentation-database-list
Tokyo, Japan
https://www.i-pro.com/
Authorised Representative in EU:
i-PRO EMEA B.V.
Laarderhoogtweg 25, 1101 EB
Amsterdam, Netherlands
i-PRO EMEA B.V. UK Branch
1010 Cambourne Business Park,
Cambridgeshire CB23 6DP
Step2 Processing the installation surface
Step1 Preparations
Parts and functions
Step4 Mount the camera
Step5 Adjustment
β– Indicators
Note:
σ±Ύ€Lighting/blinking LED can be turned off with the software settings at any time. (The initial state is lighting or
blinking.) Refer to the Operating instructions, and set the LED to be solid off if necessary.
LINK indicator
When the camera is able to communicate with the connected device Lights orange
ACT indicator
When data is being sent via the network camera Blinks green (accessing)
β– Buttons
β€’INITIAL SET button (Initializing)
Follow the steps below to initialize the network camera. Retry if the camera does not start up normally.
*Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and
may cause malfunction.
β€’TELE button
Push the TELE button to adjust the zoom ratio to the β€œTele” side.
β€’WIDE button
Push the WIDE button to adjust the zoom ratio to the β€œWide” side.
<Whole unit>
RJ45 Network connector
【2γ€‘ξ˜Download and launch "IP Setting Software" <Control No.: C0123> or "i-PRO
Configuration Tool (iCT)" <Control No.: C0133> on our support website, and
connect to the network.
【1γ€‘ξ˜Turn on the camera.
【3γ€‘ξ˜Adjust the camera direction.
β‘ Loosen TILT fixing screw.
β‘‘Adjust the horizontal (PAN) angle, vertical (TILT) angle, and
azimuth (YAW) angle while watching the screen of the PC
on the network.
Horizontal (PAN)angle : Β±180Β°
Vertical (TILT) angle : -30Β° to +85Β°
Azimuth(YAW) angle : Β±100Β°
【4γ€‘ξ˜Adjust the zoom ratio of the camera.
Adjust the zoom ratio using the TELE button and the WIDE
button while watching the screen.
PAN table
Azimuth
(YAW)
adjustment
ring
Camera
Enclosure
TILT fixing
screw
Dome cover
<Camera body>
●Points up when installing
to a wall.
Direction marker for
installation (TOP ⇧)
INITIAL SET
button
ACT indicator
LINK indicator
WIDE button
TELE button
●FRONT should face the
camera front (the side of
the i-PRO logo).
Direction marker for
installation (FRONT ⇩)
<Terminals>
【1γ€‘ξ˜Loosen the enclosure fixing screws
(2 places), and remove the enclosure
from the camera.
Enclosure
When installing the camera on the ceiling or wall with cables exposed, cut out a portion of the enclosure to
open a cable access hole.
Using the side cable access hole
Side cable access hole
Enclosure
fixing screw
(2 places)
Note:
σ±Ύ€When installing on a wall, make a hole so as to face the β€œ
⇧T (TOP)” mark of the template to the upper side.
σ±Ύ€When installing on a ceiling, make a hole so as to face the β€œ
⇩F (FRONT)” mark of the template to the
front side of the camera (in the direction of i-PRO logo).
σ±Ύ€When running the cable using the side cable access hole of the camera, it is unnecessary to make a
cable access hole on the installation surface.
Drill a hole in the installation surface. (2 screw holes / 1 cable access hole).
Step3 Making connections
Note:
σ±Ύ€Since the connector storage section does not
have a sufficient space, use an Ethernet cable
that do not exceed the sizes described in the
illustrations.
Straight section
30 mm {1-3/16 inches}
13 mm {1/2 inches}
Fixing screw
(M4: locally procured)
Secure the camera with fixing screws (2 pcs.) (M4:locally procured).
Minimum pull-out strength: 196 N {44 lbf}
【5γ€‘ξ˜Attach the enclosure and secure it by
tightening the enclosure fi xing screws.
【6γ€‘ξ˜After complete installation, remove the protection fi lm from the dome
cover.
Note:
σ±Ύ€When the camera is installed on a wall, the gradient
viewed from the camera is backwards. Images displayed
from the camera can be reversed by setting "Image rota-
tion" to "180Β° (Upside-down)" in the setup menu. For
information about configuring "Image rotation" in the
setup menu, refer to the Operating Instructions.
σ±Ύ€When using the camera at a vertical position angle of
75Β°or more (a position where the camera lens is nearly
horizontal), part of the image may appear to be over-
lapped due to influence from the dome cover. To pre-
vent overlapping, decrease the vertical position angle
or adjust the zoom ratio.
σ±Ύ€When adjusting the camera, do not touch IR LED
sheets with your fingers.
β‘’After adjusting the direction, fix the camera by tightening
the TILT fixing screw.
Recommended tightening torque:0.59 NΒ·m {0.44 lbfΒ·ft}
Turn on the power of the
camera while pressing
the INITIAL SET button
⇨
Turn off the
power of
the camera
Make sure
to release
the button
15 seconds
The camera will start up and the
settings including the network
settings will be initialized
around
2 minutes
⇨ ⇨
IMPORTANT:
σ±Ύ€To prevent injuries and protect the cables, finish the side cable
access hole with a file to avoid sharp edges.
microSD slotSymbol of the microSD
Camera fixation
position
Direction marker for
installation (TOP ⇧)
Direction marker for
installation (FRONT ⇩)
IMPORTANT:
σ±Ύ€Devices to which power can be supplied to this product are PoE hub and PoE power supplying equipment.
σ±Ύ€Turn off each system’s power supply before making a connection.
Less than 100 m {328 feet}
Ethernet cable (category 5e or better,
straight, 4 pairs (8 pins))
9 mm
{11/32 inches}
40 mm
{1-9/16 inches}
β– ξ˜Insert a microSD memory card
Back end of
the microSD
memory card
microSD memory card
Symbol of the microSD microSD slot
WIDE button TELE button
Attach the enclosure by aligning the i-PRO logo to the
direction marker (FRONT ) on the camera.for installation ⇧
Recommended tightening torque: 0.59 NΒ·m {0.44 lbfΒ·ft})
β–  Remove a microSD memory card
When removing a microSD memory card, reverse the procedure.
β‘ Remove the enclosure from the camera.
β‘‘Remove the micro SD memory card by pushing it down until a click sound is heard while holding the card
with a fi nger to prevent it from popping out.
β‘’ Attach the enclosure to the camera again.
Note:
σ±Ύ€When using a microSD memory card, format it using this product. Refer to the Operating Instructions
for how to format a microSD memory card.
σ±Ύ€Use the compatible microSD memory cards. Refer to our support website <Control No.: C0107> for
latest information about the compatible microSD memory cards.
IMPORTANT:
σ±Ύ€When removing a microSD memory card, make sure to set "SD memory card" to "Not use" on the
[SD memory card] tab of the setup menu before removing the microSD memory card. After removing
the memory card, set back the "SD memory card" to "Use". For information about the setup menu,
refer to the Operating Instructions.
Insert / remove a microSD memory card
β‘ Remove the enclosure from the camera.
β‘‘
Insert the microSD memory card into the end of the microSD slot
and confi rm that a clicking sound is made.
β‘’ Attach the enclosure to the camera again.
σ±Ύ€Screen display
down direction
【2】 If necessary, insert a microSD memory
card by referring to β€œInsert / remove a
microSD memory card”.
Azimuth
(YAW)
angle
Vertical (TILT)
angle
Horizontal (PAN)
angle
TILT fixing screw
PAN
table
Azimuth (YAW)
adjustment ring
IR LED
sheets
Note:
σ±Ύ€After approx. 3 seconds from releasing the TELE button or the WIDE button, the auto focus function will
automatically be executed. Do not touch the camera during execution of the auto focus function.
σ±Ύ€
Attaching the enclosure may cause slight defocusing. In this case, execute the auto focus function from the setup
menu after attaching the enclosure and removing the protection film.
σ±Ύ€
When the resolution is set to higher than 640Γ—360, image quality may deteriorate depending on the zoom
ratio. Refer to our support website <Control No.: C0124> for further information.ξ™½
Enclosure
Enclosure fixing
screw (2 places)
Dome cover
Direction marker
for installation
(FRONT ⇩)
Cable access hole
(ΓΈ30 mm {ΓΈ1-3/16 inches})
Hole for the
fixing screw
(camera fixation
position)
20 mm
{13/16 inches}
83.5 mm
{3-9/32 inches}
46 mm
{1-13/16 inches}
β€œβ–Όβ€Symbol
Camera fixation position
Mount the camera to a junction box
PAN table
PAN table fixing
screw hole
Note:
σ±Ύ€When installing the enclosure, align the enclosure fixing
screw position in advance and install the enclosure
straight onto the installation surface so that the direc-
tion of the camera does not change.
If the direction of the camera is changed, insert the
PAN table fixing screw (accessory) into the PAN table
fixing screw hole (Refer to β€œParts and functions”.) and
then fix the direction of the camera by tightening the
PAN table fixing screw.
Recommended tightening torque:
0.59 NΒ·m {0.44 lbfΒ·ft}
σ±Ύ€When attaching the enclosure to the camera, check
that the dustproof sheet is attached to the inside of the
enclosure.
Built-in microphone hole
<WV-U21300-V2L>
Built-in microphone
<WV-U21300-V2L>
The following are descriptions when using the WV-U2142LA.
Dustproof sheet

Product specificaties

Merk: I-PRO
Categorie: Bewakingscamera
Model: WV-U21300-V2L

Heb je hulp nodig?

Als je hulp nodig hebt met I-PRO WV-U21300-V2L stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Bewakingscamera I-PRO

I-PRO

I-PRO WV-U31301-F2L Handleiding

16 December 2024
I-PRO

I-PRO WV-S32402-F2L1 Handleiding

16 December 2024
I-PRO

I-PRO WV-X15600-V2LN Handleiding

16 December 2024
I-PRO

I-PRO WV-X25580-F2LN2 Handleiding

16 December 2024
I-PRO

I-PRO WV-X25500-V3LN Handleiding

16 December 2024
I-PRO

I-PRO WV-X15300-V3LN Handleiding

16 December 2024
I-PRO

I-PRO WV-U2540LA Handleiding

16 December 2024
I-PRO

I-PRO WV-U2530LA Handleiding

16 December 2024
I-PRO

I-PRO WV-U21300-V2L Handleiding

16 December 2024
I-PRO

I-PRO WV-U1542LA Handleiding

16 December 2024

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Bolin Technology

Bolin Technology VCC-M2H10BI-4FN1 Handleiding

16 December 2024
Bolin Technology

Bolin Technology Blue Line B2-220 Handleiding

16 December 2024
Bolin Technology

Bolin Technology Blue Line B7-220 Handleiding

16 December 2024
Bolin Technology

Bolin Technology FEX-SN-M02202021 Handleiding

16 December 2024
Bea-fon

Bea-fon Tracer 1T Handleiding

14 December 2024
Bea-fon

Bea-fon Safer 1S Handleiding

14 December 2024
VTech

VTech VC7001 Handleiding

13 December 2024
VTech

VTech VC7002 Handleiding

13 December 2024
Enabot

Enabot ROLA PetPAl Handleiding

11 December 2024
Milesight

Milesight MS-C2964-PD Handleiding

11 December 2024