I-PRO WV-U1132A Handleiding

I-PRO Bewakingscamera WV-U1132A

Lees hieronder de 📖 handleiding in het Nederlandse voor I-PRO WV-U1132A (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

• Before attempting to connect or operate this product, please read these instructions

carefully and save this manual for future use.

• microSDXC/ microSDHC/ microSD memory card is described as microSD memory card.

• The external appearance and other parts shown in this manual may differ from the actual product within the

scope that will not interfere with normal use due to improvement of the product.

"<Control No.: C****>" used in these documents should be used to search for information

on our support website (https://i-pro.com/global/en/surveillance/training-support/support/

technical-information) and will guide you to the right information.

Model No. WV-U1142A

WV-U1132A

WV-U1130A

WV-U11300-V2

Trademarks and registered trademarks

• Microsoft, Windows, Windows Media, Internet Explorer, Microsoft Edge, and ActiveX are either registered trade-

marks or trademarks of Microsoft Corporation in the United States and/or other countries.

• Intel and Intel Core are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.

• Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe in the United States and/or

other countries.

• microSDXC Logo is a trademark of SD-3C, LLC.

• iPad and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.

• Android and Google Chrome are trademark of Google LLC.

• Firefox is a trademark of the Mozilla Foundation in the US and other countries.

• The word "QR Code" is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.

• All other trademarks identified herein are the property of their respective owners.

Troubleshooting

Before requesting service, refer to “Troubleshooting” of “Basic Information” and “Operating Instructions” . Then,

confirm the trouble.

Precautions for installation

■In order to prevent injury, the product must be securely mounted to an installation surface according

to Installation Guide.

■Installation area for this product

Select an appropriate place for the installation area (such as a strong wall or ceiling) in your particular environment.

• Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.

• Install the camera in the foundation area of the architecture or where sufficient strength is assured.

• Do not mount the product on a plaster board or a wooden section because they are too weak. If the product is

unavoidably mounted on such a section, the section shall be sufficiently reinforced.

■This camera is designed to be used indoors

This product is not operable outdoors. Do not expose this camera to direct sunlight for hours and do not install the

product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction.

Keep this camera away from water and moisture.

■Do not place this product in the following places

• Locations where a chemical agent is used such as a swimming pool

• Locations subject to moisture or oil smoke such as a kitchen

• Locations that have a specific environment that is subject to an inflammable atmosphere or solvents

• Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated

• Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot

springs, volcanic regions, etc.

• Locations where the temperature is not within the specified range

• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not

designed for on-vehicle use.)

• Locations where it may get wet directly from rain or water splash (including under the eaves, etc.)

• Locations subject to moisture or dust

• Locations subject to sudden changes in temperature such as near air discharge vents of air conditioners or air cir-

culation inlet doors

• Locations near rubber products (packing, rubber feet, etc.)

■Screw tightening

Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.

■About reflection of light from outside or IR light

A ghost may appear on the screen depending on the incident angle of external light.

In the case of using the IR light, installation of a camera near a wall may cause reflection of infrared rays resulting in

a part of the screen or the entire screen turning whitish.

• Refer to our support website <Control No.: C0109> for image examples and measures to take.

■Protection from lightning

When the cables brought from outdoors are used, there is a chance that they may be affected by lightning. In such a

case, install a lightning arrestor close to the camera, and make the length of the network cable between the camera

and lightning arrestor as short as possible to prevent the camera from being affected by lightning.

■When noise disturbance may happen

Noise may appear in video or audio near a strong electric field from a TV or radio antenna, motors and transformers,

or a strong electric field/magnetic field from a power line (lamp line) of AC100 V or more. Conduct the power distri-

bution work to keep 1 m {3.28 feet} away from them or conduct the electric conduit work using metal pipes. (Be

sure to make ground connection of the metal pipes.)

■Make sure to remove this product if it will no longer be used.

■This product has no power switch.

When turning off the power, disconnect the power supply from the PoE device.

■About the battery

A battery is installed inside the camera. Do not leave the battery exposed in environments of excessive heat as a

result of sunlight or fire.

■Equipment classification and power source indication label

Refer to the indication label on the bottom side of this unit for the equipment classification, power source, and other

information.

Specifications* *For further information, refer to the Basic Information.

: Direct current symbol Open Source Software

• This product contains open source software licensed under GPL (GNU General Public License), LGPL (GNU

Lesser General Public License), etc.

• Customers can duplicate, distribute and modify the source code of the software under license of GPL and/or LGPL.

• For details concerning licensing and source code of open source software, click “Click here for OSS information” on

“Support” page of the setup menu of this product and read the displayed content.

• Please note that we shall not respond to any inquiries regarding the contents of the source code.

Except for open source software licensed under GPL/LGPL and so on, distributing, copying, disassembling, reverse

compiling and reverse engineering of the software provided with this product are all expressly prohibited. In addition,

exporting any software provided with this product violating export laws is prohibited.

Installation Guide

Included Installation Instructions

Network Camera

For professional use only

Indoor use

■Do not insert any foreign objects.

Fire or electrical shock may be caused if water or any foreign objects, such as metal objects, enter inside the unit.

Turn the power off immediately and contact qualified service personnel for service.

■Do not use this product in an inflammable atmosphere.

Failure to observe this may cause an explosion resulting in injury.

■Avoid installing this product in the locations where salt damage occurs or corrosive gas is produced.

Otherwise, the mounting portions will deteriorate and injury or accidents due to a fall of the product may occur.

■Do not strike or give a strong shock to this product.

Failure to observe this may cause injury or fire.

■Keep microSD memory cards away from infants and children.

Otherwise, they may swallow the cards by mistake.

In this case, consult a doctor immediately.

■Do not hang down from this product or use this product as a pedestal.

Failure to observe this may cause injury or accidents.

■Do not attempt to disassemble or modify this product.

Failure to observe this may cause fire or electric shock. Consult the dealer for the repair or inspections.

■Do not install or clean the camera, or touch this product, the power cable or the connected cables

during thunder storms.

Failure to observe this may cause electric shock.

■Refer installation work to the dealer.

Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or

damage to the product.

Be sure to consult the dealer.

■Stop the operation immediately when something is wrong with this product.

When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product

has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or damage to the product.

In this case, turn the power off immediately and contact qualified service personnel for service.

■Select an installation area that can support the total weight.

Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or

accidents. Installation work shall be started after sufficient reinforcement.

■Periodic inspections shall be conducted.

Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.

Consult the dealer for the inspections.

■Install this product in a location high enough to avoid people and objects from bumping the product.

Failure to observe this may cause injury.

■The measures of protection against a fall of this product shall be taken.

Failure to observe this may cause a drop resulting in injury.

Be sure to install the safety wire.

■Do not install this product in locations subject to vibration.

Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.

■Install the product securely on an installation surface in accordance with the installation instructions.

Failure to observe this may cause injury or accidents.

■Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

■Turn the power off when cleaning this product.

Failure to observe this may cause injury.

Power source *1: PoE (IEEE802.3af compliant)

Power consumption *1:PoE DC 48 V : 100 mA/ Approx. 4.8 W (Class 2 device)

U1142

PoE DC 48 V : 90 mA/ Approx. 4.3 W (Class 2 device)

U1132

PoE DC 48 V : 80 mA/ Approx. 3.8 W (Class 2 device)

U1130

Operating environment

Ambient operating temperature:

Ambient operating humidity:

–10 °C to +50 °C {14 °F to 122 °F}

(Power On range: 0 °C to 50 °C {32 °F to 122 °F})

10 % to 90 % (no condensation)

Storage environment

Storage temperature:

Storage humidity:

–30 °C to +60 °C {–22 °F to +140 °F}

10 % to 95 % (no condensation)

Built-in microphone

<WV-U11300-V2>

Nondirectional electret condenser microphone

Dimensions: 59 mm (W) × 49 mm (H) × 116 mm (D)

{2-5/16 inches (W) × 1-15/16 inches (H) × 4-9/16 inches (D)}

(excluding projection of the slide cover)

Mass: Approx. 200 {0.44 lbs} g

U1142

Approx. 155 {0.34 lbs} g<WV-U1132A>

Approx. 165 {0.36 lbs} g<WV-U11300-V2>

Approx. 150 {0.33 lbs} g

U1130

Finish:

Main body

: ABS/PC resin, i-PRO white

*1 Refer to our support website <Control No.: C0106> for further information about Power source and

Power consumption information.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to

applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

NOTE: This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equip-

ment generates, uses, and can radiate radio frequen-

cy energy and, if not installed and used in accor-

dance with the instruction manual, may cause harm-

ful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case the

user will be required to correct the interference at his

own expense.

FCC CAUTION: Changes or modifications not

expressly approved by the party responsible for com-

pliance could void the user's authority to operate the

equipment.

Supplier’s Declaration of conformity

Trade name : i-PRO

Model No. : WV-U1142A, WV-U1132A,

WV-U1130 A, WV-U11300-V2

Responsible Party :

i-PRO Americas Inc.

8550 Fallbrook Drive, Suite 200 Houston,

Texas 77064

Support Contact : 1-800-513-5417

For U.S.A.

CAN ICES-3(A)/NMB-3(A)

For Canada

The model number and serial number of this prod-

uct may be found on the surface of the unit.

You should note the model number and serial num-

ber of this unit in the space provided and retain this

book as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

For U.S.A.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

For U.S.A.

Standard accessories

*1 This label may be required for network management. Use caution not to lose this label.

Other items that are needed (not included)

• Mounting screw

•RJ45plug, Ethernet cable (category 5e or better, straight, 4 pairs (8 pins))

•Tools

Installation Guide (this document) ..................... 1 pc.

IMPORTANT SAFETY INSTRUCTIONS ............. 1 pc.

<WV-U1142A><WV-U1132A><WV-U1130A>

Code label*1...................................................... 1 pc.

The following parts are used during installation procedures.

Safety wire ........................................................ 1 pc.

Washer ............................................................. 1 pc.

Spring washer .................................................. 1 pc.

Indoor use

About notations

The following notations are used when describing the functions limited for specified models.

The functions without the notations are supported by all models.

U1142

The functions with this notation are available when using the model WV-U1142A (4M pixel model).

U1132

The functions with this notation are available when using the model WV-U1132A, WV-U11300-V2

(2M pixel model).

U1130

The functions with this notation are available when using the model WV-U1130A (2M pixel model).

WV-U1142A

Caution:

• The network camera is only intended for a connec-

tion to an ethernet or PoE network without routing to

the outside plant.

• This product has no power switch. Be sure to install

disconnect devices such as a circuit breaker to shut

down the main power of power supplying equipment

to this product.

• Before attempting to connect or operate this product,

please read these instructions carefully.

Notice:

• This product is not suitable for use in locations where

children are likely to be present.

• Do not install this product in locations where ordinary

persons can easily reach.

• This product is a professional equipment.

• For information about screws and other parts

required for installation, refer to the corresponding

section of this document.

Precautions

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out

of improper installation or operation inconsistent with this

documentation.

avs0821-2033

Printed in China

* La longueur de la vis est un exemple lors de l’installation de la caméra au plafond

ou sur un mur robuste d’une épaisseur de 20 mm {25/32 pouces} ou plus.

Méthode d’installation Vis de fixation

recommandée

La capacité de traction

minimale requise

Pour une installation au plafond

Platine de fixation d’installation: 260 {0,57 lbs}g

Caméra vidéo: Maxi.200 {0.44 lbs}g

M6 x 16 mm

{5/8 pouces}/ 4 él.

562 N

{126 lbf}

Pour une installation murale

Platine de fixation d’installation: 420 {0,93 lbs}g

Caméra vidéo: Maxi.200 {0.44 lbs}g

M6 x 16 mm

{5/8 pouces}/ 4 él.

724 N

{163 lbf}

Pour fixer le câble de sécurité M4 x 16 mm

{5/8 pouces}/ 1 él.

24.5 N

{5.5 lbf}

Installation method

Recommended

screw *1Minimum pull-out strength*

For mounting on ceiling

Mount bracket: 260 {0.57 lbs}g

Camera: max.200 {0.44 lbs}g

M6 x 16 mm *3 *4

{5/8 inches} x 4 pcs. 562 N {126 lbf} *5

M4 x 16 mm *3

{5/8 inches} x 1 pc. 24.5 N {5.5 lbf}

For mounting on wall

Mount bracket: 420 {0.93 lbs}g

Camera: max.200 {0.44 lbs}g

M6 x 16 mm *3 *4

{5/8 inches} x 4 pcs. 724 N {163 lbf} *5

M4 x 16 mm *3

{5/8 inches} x 1 pc. 24.5 N {5.5 lbf}

*1 Select screws according to the material of the location that the camera will be mounted to. In this

case, wood screws and nails should not be used.

*2 This value indicates the minimum pull-out strength required value per screw. For information about the

minimum pull-out strength, refer to our support website <Control No.: C0120>.

*3 The screw length is an example when installing the camera on a robust ceiling or wall with a thickness

of 20 mm {25/32 inches} or more.

*4 The number of required screws or anchor bolts varies depending on the specifications of the mount

bracket (locally procured). Refer to the operating instructions of the mount bracket (locally procured)

for information about how to mount the mount bracket.

*5 Make sure that the screws or anchor bolts separately procured when locally procuring a mount

bracket for the ceiling or wall are capable of supporting the total weight (including the moment force

when mounting to a wall).

Ceiling

Wall

Tokyo, Japan

https://www.i-pro.com/

Authorised Representative in EU:

i-PRO EMEA B.V.

Laarderhoogtweg 25, 1101 EB

Amsterdam, Netherlands

i-PRO EMEA B.V. UK Branch

1010 Cambourne Business Park,

Cambridgeshire CB23 6DP

About the user manuals

Product documentation is composed of the following documents.

•Installation Guide (this document): Provides information about “Precautions”,

“Precautions for installation” and the installation method.

•

Basic Information (Refer to the link on the following product information website):

Provides information about “Precautions for use” and “Detail specifications”.

•

Operating Instructions (Refer to the link on the following product information website):

Explains how to perform the settings and how to operate this camera.

https://i-pro.com/global/en/surveillance/training-support/documentation-database-list

Indoor use

Parts and functions Step3 Mount (Fix in accordance with the installation method)

■Indicators

Note:

󱾀Lighting/blinking LED can be turned off with the software settings at any time. (The initial state is lighting or

blinking.) Refer to the Operating instructions, and set the LED to be solid off if necessary.

LINK indicator

When the camera is able to communicate with the connected device Lights orange

ACT indicator

When data is being sent via the network camera Blinks green (accessing)

■Buttons

•INITIAL SET button (Initializing)

Follow the steps below to initialize the network camera. Retry if the camera does not start up normally.

*

Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and

may cause malfunction.

•TELE button

Push the TELE button to adjust the zoom ratio to the “Tele” side.

•WIDE button

Push the WIDE button to adjust the zoom ratio to the “Wide” side.

Turn on the power of the

camera while pressing

the INITIAL SET button

⇨

Turn off the

power of

the camera

Make sure

to release

the button

15 seconds

The camera will start up and the

settings including the network

settings will be initialized

around

2 minutes

⇨ ⇨

Note:

󱾀Back end of the microSD memory card does not protrude

over the surface of the microSD slot (the same surface as

the microSD symbol).

■Insert a microSD memory card

Back end of

the microSD

memory card

microSD

memory card

Symbol of

the microSD

microSD

slot

■ Remove a microSD memory card

When removing a microSD memory card, reverse the procedure.

①

Open the slide cover by placing your finger on the projection of the slide cover and sliding it.

②

Remove the microSD memory card by pushing it down until a click sound is heard while holding the card

with a ﬁ nger to prevent it from popping out.

③ Close the slide cover.

Note:

󱾀When using a microSD memory card, format it using this product. Refer to the Operating Instructions

for how to format a microSD memory card.

󱾀Use the compatible microSD memory cards. Refer to our support website <Control No.: C0107> for

latest information about the compatible microSD memory cards.

IMPORTANT:

󱾀When removing a microSD memory card, make sure to set "SD memory card" to "Not use" on the

[SD memory card] tab of the setup menu before removing the microSD memory card. After removing

the memory card, set back the "SD memory card" to "Use". For information about the setup menu,

refer to the Operating Instructions.

Insert / remove a microSD memory card

①

Open the slide cover by placing your finger on the projection of

the slide cover and sliding it.

②

Insert the microSD memory card into the end of the microSD slot

and conﬁ rm that a clicking sound is made.

③Close the slide cover.

(The right illustration shows an example of WV-U1142A.)

Lens

<Top>

Wire engaging hole

<Side>

<Rear>

Slide cover

1/4-20UNC

ﬁ xing screw hole

(depth 5.5 mm

{7/32 inches})

microSD slot

INITIAL SET button

WIDE button

TELE button

ACT indicator

LINK indicator

RJ45 Network connector

【１】

Mark the position of holes to be made for the ceiling mount bracket

(locally procured) on the attachment position of the ceiling, and make

those holes for attachment.

【1】Attach the safety wire (accessory)

Ceiling

⇨

Wall

Common

󱾀Determine the mounting height of the camera so that the lowest part of the camera or

the camera mounting bracket after the installation is 2 m 80 cm {110 inches} or higher

from the floor.

②Pass the ring part of the

safety wire through the

wire engaging hole.

①Bend the ring part

of the safety wire.

③Pass the other end of the

safety wire through the ring

part of the safety wire.

Engage the safety wire (accessory) with the wire engaging hole.

Safety wire

(accessory)

【１】

Mark the position of holes to be made for the wall mount bracket (locally

procured) on the attachment position of the wall, and make those holes for

attachment.

【2】

Secure the wall mount bracket (locally

procured) using separately procured

fixing

screws or anchors.

Step1 Preparations

Step2 Processing the installation surface (Process in accordance with the installation method)

【2】

Secure the ceiling mount bracket

(locally procured) using separately

procured fixing screws or anchors.

Ceiling mount bracket

(example)

Fixing screw

(locally procured) Wall mount bracket

(example)

Fixing screw

(locally procured)

Ceiling Wall

【１】

Loosen the camera mount bracket ﬁ xing

mechanism to freely move the camera mount

bracket.

【2】



Align the screw thread with the ﬁ xing screw

hole of the camera, and rotate the camera

mount bracket to secure the camera.

【１】



Loosen the camera mount bracket ﬁ xing

mechanism to freely move the camera mount

bracket.

【2】



Align the screw thread with the ﬁ xing screw

hole of the camera, and rotate the camera

mount bracket to secure the camera.

1/4-20UNC

ﬁ xing screw hole

(depth 5.5 mm

{7/32 inches})

Camera mount bracket

ﬁ xing mechanism

Camera mount

bracket

Fixing screw hole

Camera mount bracket

ﬁ xing mechanism

Camera mount

bracket

Fixing screw hole

【2】Download and launch "IP Setting Software" <Control No.: C0123> or "i-PRO

Configuration Tool (iCT)" <Control No.: C0133> on our support website, and

connect to the network.

【1】Turn on the camera.

【3】Adjust the camera direction.

①

Loosen the camera mount bracket ﬁ xing mechanism on the camera mount bracket.

②Adjust the direction while watching the screen of the PC on the network.

③Be sure to tighten the lock lever securely after the adjustment.

【4】Adjust the zoom ratio of the

camera.

U1142

U1132

①Open the slide cover by placing your finger on

the projection of the slide cover and sliding it.

②Adjust the zoom ratio using the TELE button

and the WIDE button while watching the screen.

③Close the slide cover.

IMPORTANT:

󱾀Devices to which power can be supplied to this product are PoE hub and PoE power supplying equipment.

󱾀Turn off each system’s power supply before making a connection.

Less than 100 m {328 feet} Ethernet cable (category 5e or better,

straight, 4 pairs (8 pins))

Step4 Making connections

Step5 Adjustment

90°

360°

90°

Ceiling Wall

Camera mount bracket

ﬁ xing mechanism

Camera mount bracket

ﬁ xing mechanism

Projection of the slide cover

Slide

cover

WIDE button

TELE button

【2】

If necessary, insert a microSD memory card by referring to “Insert /

remove a microSD memory card”.

Attach the safety wire (accessory) to the foundation

area of the architecture or where sufﬁ cient strength

is assured.

【5】Fix the safety wire on the installation surface.

Ceiling Wall

Washer

(accessory)

Spring

washer

(accessory)

Ceiling mount bracket (example)

Safety wire

(accessory)

Recommended screw M4

(locally procured)

Minimum pull-out strength

24.5 N {5.5 lbf}

Attach the safety wire (accessory) to the foundation

area of the architecture or where sufﬁ cient strength

is assured.

Wall mount bracket

(example)

Safety wire

(accessory)

Washer

(accessory)

Spring

washer

(accessory)

Recommended screw M4

(locally procured)

Minimum pull-out strength

24.5 N {5.5 lbf}

Projection of the slide cover

Slide

cover

Note:

󱾀 After approx. 3 seconds from releasing the TELE button or the WIDE button, the auto focus function

will automatically be executed. Do not touch the camera during execution of the auto focus function.

󱾀 When the resolution is set to higher than 640×360, image quality may deteriorate depending on the

zoom ratio. Refer to our support website <Control No.: C0124> for further information.

Minimum pull-out strength:

Refer to the instruction guide of the wall mount bracket.

Minimum pull-out strength:

Refer to the instruction guide of the ceiling

mount bracket.

IMPORTANT:

󱾀Be sure to rotate and secure the camera mount bracket.

Rotating the camera places a large burden on the camera

mount bracket, and may cause damage.

【3】

Tighten the camera mount bracket ﬁ xing

mechanism and secure the camera mount

bracket.

IMPORTANT:

󱾀Be sure to rotate and secure the camera mount bracket.

Rotating the camera places a large burden on the camera

mount bracket, and may cause damage.

【3】

Tighten the camera mount bracket ﬁ xing

mechanism and secure the camera mount

bracket.

IMPORTANT:

󱾀When adjusting the camera angle, make sure to loosen the camera mount bracket fixing mechanism on

the camera mount bracket before making adjustments. If the camera angle is changed when the camera

mount bracket fixing mechanism is tightened, excessive force is applied to the camera mount bracket

and camera, which may damage them.

U1142

U1132

U1142

U1132

Built-in microphone hole

<WV-U11300-V2>

Product specificaties

Merk:	I-PRO
Categorie:	Bewakingscamera
Model:	WV-U1132A

Heb je hulp nodig?

Als je hulp nodig hebt met I-PRO WV-U1132A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera I-PRO

I-PRO WV-U31301-F2L Handleiding

16 December 2024

I-PRO WV-S32402-F2L1 Handleiding

16 December 2024

I-PRO WV-X15600-V2LN Handleiding

16 December 2024

I-PRO WV-X25580-F2LN2 Handleiding

16 December 2024

I-PRO WV-X25500-V3LN Handleiding

16 December 2024

I-PRO WV-X15300-V3LN Handleiding

16 December 2024

I-PRO WV-U2540LA Handleiding

16 December 2024

I-PRO WV-U2530LA Handleiding

16 December 2024

I-PRO WV-U21300-V2L Handleiding

16 December 2024

I-PRO WV-U1542LA Handleiding

16 December 2024

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Honeywell HC35WE5R3 Handleiding

20 December 2024

Honeywell Performance H4W8PER2V Handleiding

20 December 2024

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024

TP Link VIGI C450 Handleiding

18 December 2024

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024

Hikvision DS-2CE17U0T-LF Handleiding

18 December 2024