Hunter Halcyon 81030 Handleiding
Hunter
Ventilator
Halcyon 81030
Lees hieronder de 📖 handleiding in het Nederlandse voor Hunter Halcyon 81030 (15 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/15
43041-01 09/12/2011
1
Bath Ventilator with Light
Owner’s Manual
Halcyon
43034-01
20110908
©2011 Hunter Fan Co.
Model
81030
English Español
Página 22
43034-01 09/12/2011
2
W A R N I N G
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
1. For general ventilating use only. Do not use to exhaust haz-
ardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy/unbalanced impel-
lers, keep drywall spray, construction dust, etc. off power
unit.
3. DO NOT install this product in a wall. This product is
designed for installation in ceilings up to a 12/12 pitch (45
degrees). Ductwork must point upward.
4. Please read specification label on product for further infor-
mation and requirements.
PREVENTATIVE MAINTENANCE
A clean fan provides better service. Disconnect the power supply and clean the
fan as listed below.
TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a
soft cloth. DO NOT use abrasive cloths, steel wool pads or scouring powders.
TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove
motor plate, find the single tab on the motor plate (located next to the recepta-
cle). Push up rear motor plate tab while pushing out on the side of the housing
or insert a screwdriver into the slot in the housing (next to tab) and twist screw-
driver. Gently vacuum fan, motor and interior of housing.
METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN
WATER.
MAINTENANCE
The motor is permanently lubricated and never needs oiling. If the motor bear-
ings are making excessive or unusual
noises, replace the motor with the exact service motor. You should replace the
impeller at the same time.
W A R N I N GC A U T I O N
1. Use this unit only in a manner intended by the manufacturer. If
you have questions, contact the manufacturer.
2. Before servicing or cleaning the unit, switch power off at ser-
vice panel and lock the service disconnecting means to prevent
power from being switched on accidentally. when the service
disconnecting means cannot be locked, securely fasten a promi-
nent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction.
4. Sufficient air is needed for proper combustion and exhausting
of gasses through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment manufac-
turer’s guideline and safety standards, such as those published
by the National Fire Prevention Association (NFPA), and the
American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall(s) or ceiling, do not
damage electrical wiring or other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must be marked as
appropriate for the application and be connected to a GFCI (Ground
Fault Circuit Interrupter) - protected branch circuit.
8. Never place a switch where it can be reached from a tub or shower.
9. Install fan at least 5 feet (1.52 m) above the floor.
10. This unit must be grounded.
11. Unit must not be installed in a ceiling thermally insulated to a value
greater than R40.
!
!!
DISCONNECT ELECTRIC
POWER SUPPLY
AND LOCK OUT
SERVICE PANEL BEFORE
SERVICING UNIT
Do Not Install Above
Or Inside This Area
Cooking
Equipment
Floor
45° 45°
COOKING AREA
43034-01 09/12/2011
3
x2
D
E
F
G
H
I
L
M
N
95044-01-000
95029-01-000
77481-01-000
03242-07-133
98037-06-000
74508-03-133
98025-01
75184-01-133
Q
x4
*
*
*
NOTE: Strain relief cable connector
must be installed. Not
Included.
A
B
C
Extra Screws
x2
I
3/8” Cable Connec rto
O
P
J
K
65219
66002-01
77539-01
98255-01
98047-01-199
77521-01
12
E
I
Turn off the power source.
Tools Needed.
Estimated assembly time: 30 to 60 minutes
Before Installation
Check all the parts.
If damaged, call
1-888-830-1326
for replacements.
Included.
Loosen screws.
NOTE: Remove all packing materials before installation.
43034-01 09/12/2011
4
5
4
7
G
8
F
H
E
3
6
Remove the motor/blower from the housing.
Remove the pre-loaded screw tip covers.
Remove the wiring cover screw.
Back out the pre-loaded screw tips until flush
with the side of the housing.
Remove the wiring cover.
Remove packing material.
43034-01 09/12/2011
5
9
E
10
B
C
E
A11
5/8
1/2
A12
Pop out the first wiring access slug. Use second if
needed.
Insert the strain relief into the housing and
secure with the washer.
Position the correct depth mark at the bottom edge of
the joist based on the thickness of your sheetrock.
New Construction – attaching to joist
Choose Installation Option
For New Construction - attaching to joist go to step A11, page 5
For New Construction - suspended between joists go to step B11, page 8
For Existing Construction - accessible from above go to step C11, page 11
For Existing Construction - accessible only from below go to step D11,
page15
Screw pre-loaded screws into joist or framing.
43034-01 09/12/2011
6
A
3 nPi
2 nPi
Fan Motor
Light Light
Green
Black
Black
White
Black
Black
White
White Bare Copper
Ground
A14
Main Switch 1 )(AC In
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
A13
A16
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need
to be purchased.
A15
E
F
G
Install the wiring cover plate. Make sure all
wiring connections are inside the box or under
the wiring cover plate.
Connect wires as shown.
Pull wires through the strain relief.
43034-01 09/12/2011
7
A19
I
A20
Connect wiring from the motor to the wiring cover
plate.
0000
A17
0000
A18
A21
Reinstall the motor by inserting the tabs and pushing
up into position. Make sure the wires are not pinched
between the motor and the housing.
Secure the motor by tightening the 2 screws. Turn on the power source.
Test the motor. If the motor does not run, check the
plug connection.
A22
43034-01 09/12/2011
8
B11
D
E
5/8
1/2
5/8
1/2
B12
1/8" Bit
B14
B15 B16
E
B13
Slide the mounting rails into brackets.
Mark position of screws by using holes as a template.
Insert screws, leaving space between the screw
head and the joist. Screws are not provided.
New Construction – suspended between joists
Position the correct depth mark at the bottom edge of
the joist based on the thickness of your sheetrock.
Drill a hole in the center of each outline.
Attach the rails onto the screws.
43034-01 09/12/2011
9
B17 B18
Connect wires as shown.
A
3 nPi
2 nPi
Fan Motor
Light Light
Green
Black
Black
White
Black
Black
White
White Bare Copper
Ground
B19
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
B21
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need
to be purchased.
Install the wiring cover plate. Make sure all wiring
connections are inside the box or under the
wiring cover plate.
F
G
B20
Tighten screws. Pull wires through the strain relief.
43034-01 09/12/2011
10
B22
H
Connect wiring from the motor to the wiring cover
plate.
H
B23
Reinstall the motor by inserting the tabs and pushing
up into position. Make sure the wires are not pinched
between the motor and the housing.
B25
Turn on the power source.
ON
OFF
B26
Test the motor. If the motor does not run,
check the plug connection.
B24
I
Secure the motor by tightening the 2 screws.
B27
43034-01 09/12/2011
11
C12
D
E
EXISTING NFA
C11 NO EXISTING NFA
8”
8.5”
5/8
1/2
5/8
1/2
C13 C14
Existing Construction – accessible from above
OR
Remove an existing fan and check to make sure the
opening is large enough to accommodate the new
motor housing (8”x 8.5”).
Cut out an opening for the housing.
Use the motor housing as a template to mark position.
Slide the mounting rails into brackets.
Position the correct depth mark at the bottom edge of
the joist based on the thickness of your sheetrock.
Mark position of screws by using holes as a template.
43034-01 09/12/2011
12
C15
1/8" Bit
C16
C17
C18
C19 C20
Drill a hole in the center of each outline. Insert screws, leaving space between the screw head
and the joist. Screws are not provided.
Attach the rails onto the screws. Tighten screws.
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may
need to be purchased.
Pull wires through the strain relief.
43034-01 09/12/2011
13
C21
A
3 Pin
2 Pin
Fan Motor
Light Light
Green
Black
Black
White
Black
Black
White
White Bare Copper
Ground
C22
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
C24
H
G
F
C23
Tighten the strain relief screws.
Connect wires as shown.
Install the wiring cover plate. Make sure all wiring
connections are inside the box or under the
wiring cover plate.
Connect wiring from motor the motor
to the wiring cover plate.
43034-01 09/12/2011
14
C25
H
C26
I
C27
ON
OFF
C28
Secure the motor by tightening the 2 screws.
Reinstall the motor by inserting the tabs and pushing
up into position. Make sure the wires are not pinched
between the motor and the housing.
Turn on the power source. Test the motor. If the motor does not run,
check the plug connection.
C29
43034-01 09/12/2011
15
EXISTING NFA
D11
E
D12
D13
2
1
D14
E
D15
Existing Construction – accessible only from below
Pull wires through strain relief.
Remove an existing fan and check to make sure the
opening is large enough to accommodate the new
motor housing (8”x 8.5”).
Move the housing into position above the ceiling.
Attach existing ducting to duct connector. Tape joints.
If ducting does not fit securely,
an adapter may need to be purchased.
Install the housing flush with the sheetrock and secure
by tightening the pre-loaded screws into the joist.
Product specificaties
Merk: | Hunter |
Categorie: | Ventilator |
Model: | Halcyon 81030 |
Heb je hulp nodig?
Als je hulp nodig hebt met Hunter Halcyon 81030 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Ventilator Hunter
16 November 2024
11 November 2024
11 November 2024
11 November 2024
11 November 2024
11 November 2024
11 November 2024
11 November 2024
11 November 2024
11 November 2024
Handleiding Ventilator
- Ventilator Bosch
- Ventilator Philips
- Ventilator Delonghi
- Ventilator Panasonic
- Ventilator AEG
- Ventilator BEKO
- Ventilator DeWalt
- Ventilator Honeywell
- Ventilator Inventum
- Ventilator JBL
- Ventilator Medion
- Ventilator Quigg
- Ventilator Siemens
- Ventilator Tefal
- Ventilator Unold
- Ventilator Adler
- Ventilator Afk
- Ventilator Airis
- Ventilator Akasa
- Ventilator Alpina
- Ventilator Alpine
- Ventilator Andrews
- Ventilator Argo
- Ventilator Ariete
- Ventilator Asko
- Ventilator Baseline
- Ventilator Basetech
- Ventilator Be Cool
- Ventilator Beem
- Ventilator Beper
- Ventilator Bestron
- Ventilator Beurer
- Ventilator Bionaire
- Ventilator Blaupunkt
- Ventilator BlueBuilt
- Ventilator Blumill
- Ventilator Bodin
- Ventilator Bomann
- Ventilator Boneco
- Ventilator Brandson
- Ventilator Breville
- Ventilator Briebe
- Ventilator Bulex
- Ventilator Daikin
- Ventilator Defy
- Ventilator Dimplex
- Ventilator Domo
- Ventilator Duracraft
- Ventilator Duronic
- Ventilator Duux
- Ventilator Dyson
- Ventilator Easymaxx
- Ventilator Efbe-schott
- Ventilator Eglo
- Ventilator Einhell
- Ventilator Elro
- Ventilator Emerio
- Ventilator Esperanza
- Ventilator Eurom
- Ventilator Everglades
- Ventilator Evolar
- Ventilator EXCELLENT Electrics
- Ventilator Exquisit
- Ventilator Fagor
- Ventilator Fakir
- Ventilator Fisher And Paykel
- Ventilator Frankische
- Ventilator Fresh
- Ventilator Frigidaire
- Ventilator Fuave
- Ventilator G3 Ferrari
- Ventilator Gaggenau
- Ventilator Gamma
- Ventilator Gembird
- Ventilator Gemini
- Ventilator Goobay
- Ventilator Gorenje
- Ventilator Guardo
- Ventilator Gutfels
- Ventilator H.Koenig
- Ventilator Hama
- Ventilator Handson
- Ventilator Helios
- Ventilator Hema
- Ventilator Hikoki
- Ventilator Home Electric
- Ventilator Homedics
- Ventilator Hornbach
- Ventilator House Of Marley
- Ventilator HQ
- Ventilator Husqvarna
- Ventilator Hyundai
- Ventilator Ices
- Ventilator IHome
- Ventilator Innoliving
- Ventilator Itho
- Ventilator Kalorik
- Ventilator Kambrook
- Ventilator Kenmore
- Ventilator Klarbach
- Ventilator Klarstein
- Ventilator Koenic
- Ventilator Kogan
- Ventilator Korona
- Ventilator Kuppersbusch
- Ventilator Livington
- Ventilator Livoo
- Ventilator Logik
- Ventilator Maestro
- Ventilator Makita
- Ventilator Martin
- Ventilator Master
- Ventilator Meaco
- Ventilator Melissa
- Ventilator Mesko
- Ventilator Metabo
- Ventilator Midea
- Ventilator Migros
- Ventilator Milwaukee
- Ventilator Monacor
- Ventilator MPM
- Ventilator Nabo
- Ventilator Nedis
- Ventilator Perel
- Ventilator Powerplus
- Ventilator Prem-i-air
- Ventilator Primo
- Ventilator Princess
- Ventilator Profile
- Ventilator Proklima
- Ventilator Proline
- Ventilator Protector
- Ventilator Qazqa
- Ventilator Qlima
- Ventilator Renkforce
- Ventilator RestantOutlet
- Ventilator Rovus
- Ventilator Rowenta
- Ventilator Royal Sovereign
- Ventilator Ryobi
- Ventilator Sencor
- Ventilator Severin
- Ventilator Sharkoon
- Ventilator Sichler
- Ventilator Silvercrest
- Ventilator Smartwares
- Ventilator SMC
- Ventilator Sogo
- Ventilator Solac
- Ventilator Solis
- Ventilator Sonnenkonig
- Ventilator Sportstech
- Ventilator SPT
- Ventilator Stadler Form
- Ventilator Stanley
- Ventilator Steba
- Ventilator Stirling
- Ventilator Stylies
- Ventilator Sunbeam
- Ventilator Suntec
- Ventilator Superior
- Ventilator Swan
- Ventilator Sygonix
- Ventilator Taurus
- Ventilator Team
- Ventilator Techwood
- Ventilator Tecnolux
- Ventilator Termozeta
- Ventilator Tomado
- Ventilator Toolcraft
- Ventilator Trebs
- Ventilator Tristar
- Ventilator Trotec
- Ventilator Trumatic
- Ventilator Trust
- Ventilator Ufesa
- Ventilator V-Tac
- Ventilator Velleman
- Ventilator Vivax
- Ventilator Vonroc
- Ventilator Vornado
- Ventilator Wahlbach
- Ventilator Waves
- Ventilator Weasy
- Ventilator Westinghouse
- Ventilator White Knight
- Ventilator Worx
- Ventilator Zehnder
- Ventilator Zelmer
- Ventilator Jata
- Ventilator Jocel
- Ventilator OK
- Ventilator OneConcept
- Ventilator Orcon
- Ventilator Orion
- Ventilator Ozito
- Ventilator Clas Ohlson
- Ventilator Crivit
- Ventilator Becken
- Ventilator Black And Decker
- Ventilator Camry
- Ventilator Clatronic
- Ventilator Concept
- Ventilator ECG
- Ventilator Elba
- Ventilator Essentiel B
- Ventilator German Pool
- Ventilator Guzzanti
- Ventilator Heinner
- Ventilator Izzy
- Ventilator Khind
- Ventilator Mellerware
- Ventilator Optimum
- Ventilator Orbegozo
- Ventilator Scarlett
- Ventilator Sinbo
- Ventilator Trisa
- Ventilator Vox
- Ventilator CSL
- Ventilator Anslut
- Ventilator Nitecore
- Ventilator Kunft
- Ventilator Soler And Palau
- Ventilator Aspes
- Ventilator Comfee
- Ventilator Costway
- Ventilator EMOS
- Ventilator Infiniton
- Ventilator Nevir
- Ventilator Orima
- Ventilator Svan
- Ventilator Cotech
- Ventilator Ardes
- Ventilator Eldom
- Ventilator Grunkel
- Ventilator Premium
- Ventilator Teesa
- Ventilator Heylo
- Ventilator Prime3
- Ventilator Proficare
- Ventilator SereneLife
- Ventilator Thermaltake
- Ventilator Brentwood
- Ventilator Arno
- Ventilator DCG
- Ventilator Biltema
- Ventilator Sun Joe
- Ventilator Eurolite
- Ventilator Corsair
- Ventilator Broan
- Ventilator Day
- Ventilator NuTone
- Ventilator Canarm
- Ventilator CasaFan
- Ventilator Fanco
- Ventilator Jan Des Bouvrie
- Ventilator KDK
- Ventilator Kichler
- Ventilator Lucci
- Ventilator Martec
- Ventilator Vortice
- Ventilator Bimar
- Ventilator Crane
- Ventilator Kemot
- Ventilator Lasko
- Ventilator Tripp Lite
- Ventilator Antari
- Ventilator Tesy
- Ventilator Craftsman
- Ventilator Orava
- Ventilator Signature
- Ventilator SPC
- Ventilator Cecotec
- Ventilator Baxi
- Ventilator Thermex
- Ventilator Keystone
- Ventilator Enermax
- Ventilator EVOLVEO
- Ventilator Carrier
- Ventilator Fantini Cosmi
- Ventilator LC-Power
- Ventilator Tornado
- Ventilator LifeSmart
- Ventilator EcoAir
- Ventilator SHE
- Ventilator Perfect Aire
- Ventilator Air & Me
- Ventilator Ausclimate
- Ventilator Cli-Mate
- Ventilator Be Quiet!
- Ventilator Air King
- Ventilator Wahoo Fitness
- Ventilator Argoclima
- Ventilator Heller
- Ventilator PAX
- Ventilator Clean Air Optima
- Ventilator Tron
- Ventilator Arctic Cooling
- Ventilator ORNO
- Ventilator StarTech.com
- Ventilator Gamdias
- Ventilator Schweigen
- Ventilator Salco
- Ventilator Lian Li
- Ventilator NewAir
- Ventilator Arebos
- Ventilator Portacool
- Ventilator Neo
- Ventilator Rok
- Ventilator Madeira
- Ventilator Siku
- Ventilator PureGuardian
- Ventilator Aerian
- Ventilator Claro
- Ventilator IXL
- Ventilator XPower
- Ventilator JAP
- Ventilator O2 Cool
- Ventilator Elix
- Ventilator Arcoaire
- Ventilator Djive
- Ventilator InnoGIO
- Ventilator Casablanca
- Ventilator B-Air
- Ventilator Wallair
- Ventilator White Shark
- Ventilator Maico
- Ventilator Envira-North
- Ventilator Vitammy
- Ventilator GoldAir
- Ventilator Sôlt
- Ventilator SEPA
- Ventilator Ravanson
- Ventilator SchwankAir
- Ventilator Calibo
- Ventilator Create
- Ventilator Fantech
- Ventilator Aeratron
- Ventilator ActiveJet
- Ventilator Big Ass Fans
- Ventilator Haus & Luft
- Ventilator Omega Altise
- Ventilator SpeedComfort
- Ventilator Klimat
- Ventilator Eligent
- Ventilator Gewiss
- Ventilator Phaesun
- Ventilator Middle Atlantic
- Ventilator Kincrome
- Ventilator AireRyder
- Ventilator Fanimation
- Ventilator Air Logic
- Ventilator Ebm-papst
- Ventilator Sandia Aerospace
- Ventilator HPM
- Ventilator Geek Aire
- Ventilator Magmatic
- Ventilator Imarflex
- Ventilator Mystery
- Ventilator S&P
- Ventilator Modern Fan Co.
- Ventilator Quorum International
- Ventilator Yamazen
- Ventilator Windmill
- Ventilator Soler & Palau
Nieuwste handleidingen voor Ventilator
28 December 2024
20 December 2024
20 December 2024
20 December 2024
18 December 2024
14 December 2024
14 December 2024
14 December 2024
14 December 2024
13 December 2024