Humminbird HELIX 5 CHIRP GPS G3 PT Handleiding
Humminbird
Visvinder
HELIX 5 CHIRP GPS G3 PT
Lees hieronder de 📖 handleiding in het Nederlandse voor Humminbird HELIX 5 CHIRP GPS G3 PT (14 pagina's) in de categorie Visvinder. Deze handleiding was nuttig voor 70 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/14
1
532503-2_B
HELIX® PORTABLE CONTROL HEAD Installation Guide
Follow the instructions in this installation guide to install the control head in the portable case.
There may be some minor differences between the hardware described in this manual and the actual
hardware included, depending on the configuration you purchased. We encourage you to read this
guide completely so that you may understand the installation requirements.
Technical Support: If you find that any items are missing from your installation kit, visit our Web site
at humminbird.com or contact Humminbird Technical Support through our Help Center at https://
humminbird-help.johnsonoutdoors.com/hc/en-us.
Supplies: In addition to the installation kit, you will need a Phillips-head screwdriver, flat-head
screwdriver, awl, hammer, and pliers.
NOTE: The procedures and features described in this guide are subject to change without notice.
This guide was written in English and may have been translated to another language. Humminbird
is not responsible for incorrect translations or discrepancies between documents.
NOTE: The illustrations in this guide may not look the same as your product, but your unit will
function in the same way.
Portable Conversion Kit
If you have a Portable Conversion Kit, you must first un-install the control head and the transducer
from their fixed mounting positions before performing the portable installation instructions
described in this guide. Once you have converted the control head and the transducer to portable
configurations, you will be ready to mount the portable case.
1 | Converting the Control Head to Portable
1. Disconnect the cables from the control head installed on your boat.
2. Loosen the gimbal knobs and slide the control head out of the gimbal bracket.
3. Go to and follow the instructions through the section Portable Case Assembly Installing the
Base in the Portable Bag.
2 | Converting the Transducer to Portable
1. Unscrew the transducer from the fixed mounting bracket on your boat, saving the original
screws for any future fixed mounting configuration (new portable mounting screws are
provided in the Portable Conversion Kit).
2. Proceed to the portable transducer installation guide and follow the instructions to install the
transducer.
Installation Preparation
1 | Charging the Battery
You should fully charge your battery before using it for the first time to ensure peak performance.
You should also re-charge your battery at least once every 6 months to maintain your battery’s peak
performance levels. This is especially important during periods of prolonged storage.
WARNING! Do NOT use the Humminbird charger with other manufacturers’ batteries. The
Humminbird charger is only compatible with Humminbird batteries. If you have questions, please
see our Web site at or contact Humminbird Technical Support through our Help humminbird.com
Center at .https://humminbird-help.johnsonoutdoors.com/hc/en-us
NOTE: Some international models may not include a battery or battery charger.
2
532503-2_B
HELIX® PORTABLE CONTROL HEAD Installation Guide
1. Charge the battery, using the included battery charger, until it is fully charged as indicated by
the LED on the charger. Charging usually requires 8 continuous hours, but may vary depending
on your configuration.
NOTE: The battery charger uses a yellow LED to indicate it is charging. On some models, this
light might appear closer to orange than yellow. When this happens, the battery is still
charging properly and should be left to charge until the LED becomes green.
2. Slide the battery terminal adapter over each spade terminal.
CAUTION! Do not pull on the battery or charger cables when you are trying to connect them
or disconnect them from the battery terminals. Push or pull gently on the spade terminals
instead. If the connector feels tight, use a slight wiggling motion to slide the spade connector
into place on the terminal.
NOTE: The Battery Terminal Adapter allows you to power your control head and charge it at
the same time.
Portable Case Assembly
Perform the portable case assembly tasks in order, referring to the step-by-step procedures that
represent the following main assembly tasks:
∆Installing the riser blocks and gimbal bracket onto the portable base
∆Routing the cables in the base
∆Finalizing the portable base assembly
∆Installing the battery
∆Installing the base in the portable bag
∆Stowing the portable transducer and battery charger in the portable bag
When you are finished, the control head and the transducer will be part of the portable case
assembly. If you plan to use the portable case assembly for ice fishing, you will be ready to take your
portable case on the ice for final setup.
1 | Assembling the Portable Base
1. Turn over the base, and locate the 4 holes labeled D.
2. Use a screwdriver (or an awl) with a hammer to punch out the selected mounting holes.
3. Turn the base right side up.
4. Install the riser blocks on the portable base using the following guidelines:
∆Line up the holes on the riser blocks with the holes you punched out of the base in step 2.
∆Align the riser blocks so that the wider end of each block is on the base. The narrow end of each
riser block should be facing up. The angled corners on the riser blocks should be facing out.
∆See the illustrations and .Aligning the Riser Blocks Installing the Riser Blocks on the Base
Aligning the Riser Blocks
angled corners
should point out
Align the screw holes on the riser blocks with the punched-out holes in the base.
Handling the Spade Terminals
Punching Holes
3
532503-2_B
HELIX® PORTABLE CONTROL HEAD Installation Guide
5. Secure the riser blocks to the base with the four included #8-15 x 3/4" screws. See the
illustration . Installing the Riser Blocks on the Base Hand tighten only!
CAUTION! Do not use a high speed driver on this combination of fasteners. Hand tighten only.
6. Select the gimbal bracket for your control head model.
7. Line up the mounting holes on the gimbal bracket with the screw holes on the top of the riser
blocks. Make sure the opening in the gimbal bracket arms faces away from the battery well
on the base.
Installing the Gimbal Bracket on the Riser Blocks
screw
Confirm the
screw holes on
the riser blocks
align with the
screw holes on
your gimbal
bracket.
battery well
8. Using a Phillips-head screwdriver, secure the gimbal bracket with the four included #8 x 1 1/4"
screws. Hand tighten only!
9. Route the power cable and the transducer jumper cable from under the base and up through
the hole in the base. See the illustration .Portable Base Assembly
10. Install the gimbal knobs into each side of the control head. Tighten the knobs just enough so
you can slide the control head into the gimbal bracket arms.
11. Insert the power and the transducer jumper cable connectors into the correct ports on your
control head. Refer to the illustration that matches the number of ports on your control head.
NOTE: The control head ports are keyed to prevent reversed installation, so be careful not to
force the connectors into the wrong ports.
COM (communications)
transducerpower
Control Head with 3 Ports Control Head with 4 Ports
(includes Ethernet)
power transducer
COM (communications)
Ethernet
12. Confirm there is enough cable slack to allow the control head to pivot through its full tilt range
and for connecting or disconnecting the cables. Carefully pull the excess cable from beneath
the portable base.
13. Disconnect the cables from the control head. Slide the control head out of the gimbal bracket
and set it aside.
It is important to note the amount of cable you will need to reconnect to the control head when
you install it on the portable base later in the installation.
opening
in bracket
arms
Portable Base Assembly
cables routed
behind the
bracket
install each
riser block
with the
narrow end
facing up
screw
Installing the Riser Blocks
on the Base
Product specificaties
| Merk: | Humminbird |
| Categorie: | Visvinder |
| Model: | HELIX 5 CHIRP GPS G3 PT |
Heb je hulp nodig?
Als je hulp nodig hebt met Humminbird HELIX 5 CHIRP GPS G3 PT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Visvinder Humminbird
23 Juli 2023
23 Juli 2023
20 Juni 2023
21 Mei 2023
9 Mei 2023
25 April 2023
13 April 2023
12 April 2023
Handleiding Visvinder
- Visvinder Garmin
- Visvinder Eagle
- Visvinder Furuno
- Visvinder Lowrance
- Visvinder Raymarine
- Visvinder Simrad
- Visvinder Lucky
- Visvinder Deeper
- Visvinder Closer Pets
Nieuwste handleidingen voor Visvinder
16 November 2024
14 November 2024
4 September 2024
11 Januari 2024
27 Augustus 2023
27 Augustus 2023
1 Juli 2023
20 Juni 2023
18 Juni 2023
18 Juni 2023