HQ TVS--FSB07B Handleiding

HQ Tv-meubel TVS--FSB07B

Lees hieronder de 📖 handleiding in het Nederlandse voor HQ TVS--FSB07B (4 pagina's) in de categorie Tv-meubel. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTALLATION INSTRUCTIONS

Max Load Capacity: 30kg(66lbs)

30kg

(66lbs)

MAX

Pitching angle:

-20° ~ +20°

Swivel: 180°

LCD Wall Mount

Maintenance

Once you have mounted the bracket and the flat screen, check that they are sufficiently secure and safe to

use. You should check whether screws are fixed well each two months. If you have any doubts regarding the

installation, please consult our retailer or service department for detail.

Pitching angle adjustment

• Use the tilt adjusting knob to adjust your TV to the desired angle, the pitching angle can be adjusted

between -20°~20°, as shown in fig 5.1.

fig. 5.1

wall

Tilt adjusting knob

NOTE: Read entire instruction sheet before you start installation and assembly.

WARNING

• Do not begin the installation of the product before you have read and understood the

instructions and warnings contained in this installation sheet. If you have any question

regarding any of the instruction or warning, please contact your local distributor.

• Please refer to installation guide recommendation for required distance from wall to

avoid risk of property damage.

• This product should only be installed by someone of good mechanical aptitude, with

experience and basic building, and fully understands.

• Make sure that the supporting surface will safely support the combined load of the

equipment and all attached hardware and components.

• Never exceed the maximum load capacity.

• If mounting to wood wall studs, make sure that mounting screws are anchored into

the center of the studs. Use of an “edge to edge” stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position

equipment.

• Tighten screws firmly, but do not over tighten. Over tightening can damage the items,

greatly reducing their holding power.

• This products intended for indoor use only. Using this product outdoors could lead to

product failure and personal injury.

Component Checklist

IMPORTANT: Ensure you have received all parts against the component checklist prior to installing. If any parts

are missing or faulty, telephone the special franchiser for a replac ement.

Package M

Package W

Tools required

Phillips Head Screw driver(200mm length exclude the handle)

M6 Socket and wrench

Electric drill and 10mm masonry bit for concrete wall installation

Marking Pen

Hammer

ST6.3x55 (x6)

W-A

lag bolt concrete anchor

W-B

(x6) D (ø xø )

washer (x6)

W-C

6 6.3 16

M4x10

M-A

(x4) M5x10 (x4)

M-B

D4 ( 4.5x )

washer (x4)

M-E

ø ø10 D (ø .5xø )

washer (x4)

M-F

5 5 12

M6x10 (x4)

M-C

D6 (ø6.3xø )

washer (x4)

M-G

M8x15 (x4)

M-D

D8 (ø8.3xø )

(x5)

M-H

washer

ø13.5xø5.5x3.2 (x4)

M-I

decorative cover 1

(x1)

left decorative cover (x1)

Gright decorative cover (x1)

wall plate(x1)

adapter bracket (x1)

grip holder (x1)

M8 (x1)

M-J

M8 (x2)

M-K

M8x20 (x1)

M-L

M8x50 (x1)

M-M

M8 (x1)

M-N

decorative cover 2 (x1)

decorative cover 3

(x1) decorative cover 4 (x1)

washer (x1)

M-O

WOOD STUD WALL MOUNTING:

WARNING

• Make sure that the supporting surface will safely support the combined load of the

equipment and all attached hardware and components.

• Tighten wood screws firmly, but do not over tighten. Over tightening can damage

the screws, greatly reducing their holding power.

• Make sure that mounting screws are anchored into the center of the studs. Use of

an “edge to edge” stud finder is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall

or plaster into studs. Installers are responsible to provide hardware for other types

of mounting situations.

fig. 1.1

WARNING

• When installing wall mounts on cinder block, verify that you have a minimum of

1-3/8” of actual concrete thickness in the hole to be used for the concrete anchors.

Do not drill into mortar joints! Be sure to mount in a solid part of the block,

generally 1” minimum from the side of the block. It is suggested electric drill on

slow setting is used to drill the hole instead of a hammer drill to avoid breaking out

the back of the hole when entering a void or cavity.

• Installer must verify that the supporting surface will safely support the combined

load of the equipment and all attached hardware and components.

SOLID BRICK AND CONCRETE BLOCK MOUNTING:

• Pre-drill these holes with a 10mm masonry bit to at least 60mm in depth. Insert a Concrete Anchor (W-B)

into each of these holes. Attach the Wall Plate to the wall using six wood screws (W-A) and six washers

(W-C), as shown in fig.1.3.

• Use the Wall Plate as a template to mark six holes locations on the wall, as shown in fig.1.2.

recommended. Based on their edges, draw a vertical line down each stud’s center.

• Place wall plate on wall as a template. And mark the center of the two mounting holes. Make sure that

the mounting holes are on the stud centerline.

• Drill two 1/8” (3mm) dia. Holes 1.2” (30mm) deep. Make sure that the wall plate is level, secure it using

two wood screws (W-A) and two washers(W-C) as shown in fig. 1.1.

• Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly

Stud

W-A

W-C

fig. 1.2 fig. 1.3

• Assembled the adapter bracket with appropriate parts as shown in fig.2.1.

• Assembled the adapter bracket and arm of wall plate with appropriate screw, washers and nut. As shown

in fig.2.2.

2Adapter bracket Mounting

W-A

W-B

W-C

Product specificaties

Merk:	HQ
Categorie:	Tv-meubel
Model:	TVS--FSB07B
Kleur van het product:	Zwart
Gewicht verpakking:	2300 g
Gebruikershandleiding:	Ja
Materiaal behuizing:	Plastic, Steel
Montagewijze:	Muur
Afmetingen verpakking (BxDxH):	385 x 75 x 255 mm
Maximale gewichtscapaciteit:	30 kg
Paneelmontage-interface:	50 x 50,75 x 75,100 x 100,200 x 100,200 x 200 mm
Horizontaal draaibaar:	-270 - 270 °
Montage interface compatibiliteit (min):	50 x 50 mm
Montage interface compatibiliteit (max):	200 x 200 mm
Bereik kantelhoek:	-20 - 20 °
Maximale schermgrootte:	32 "
Minimale schermgrootte:	10 "
Aantal draaipunten:	3
Afstand tot de muur (min):	100 mm
Afstand tot de muur (max.):	470 mm