HQ Power VDP575MHS20FL Handleiding

HQ Power Effect machine VDP575MHS20FL

Lees hieronder de 📖 handleiding in het Nederlandse voor HQ Power VDP575MHS20FL (46 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/46

VDP575MHS20FL

AERON 575S MOVING HEAD

PROJECTEUR LYRE AERON 575S

CABEZA MÓVIL AERON 575S

AERON 575S MOVING-HEAD-SCHEINWERFER

USER MANUAL

GEBRUIKERSHANDLEIDING

NOTICE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

VDP575MHS20FL_v3 HQPOWER

VDP575MHS20FL – AERON 575S MOVING HEAD

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm

the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized

company for recycling.

This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing HQPOWER! Your moving head should come in a flight case and with a 575W Sylvania light

bulb, an XLR connexion cable, a safety cable with quick-lock hook and this manual. Please read the manual thoroughly

before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your

dealer.

2. Safety Instructions

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer

will not accept responsibility for any ensuing defects or problems.

• A qualified technician should install and service this device.

• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device

against damage by leaving it switched off oom temperature. until it has reached r

• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified

person carry out the electric connection.

• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.

• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.

• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.

• There may be some smoke or a particular smell when the device is activated for the first time. This is normal and

any smoke or smell will gradually disappear.

• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.

• Note that damage caused by user modifications to the device is not covered by the warranty.

• Keep the device away from children and unauthorised users.

3. General Guidelines

• This device is designed for professional use on stage, in discos, theatres, etc. The VDP575MHS20FL should only

be used indoors and connected to an alternating current of max. 230VAC / 50Hz.

• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.

• Do not shake the device. Avoid brute force when installing or operating the device.

• Select a location where the device is protected against extreme heat (see “Technical Specifications”), dust and

moisture. Respect a minimum distance of 0.5m between the device’s light output and any illuminated surface.

Be very careful during the installation: touching live wires can cause life-threatening electroshocks.

Do not touch the device during operation as the housing heats up.

Keep this device away from rain and moisture.

Unplug the mains lead before opening the housing.

VDP575MHS20FL_v3 HQPOWER

• Use an appropriate safety cable to fix the device (e.g. VDLSC8).

• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified

people. Any damage that may occur will most probably be due to unprofessional use of the device.

• Use the original packaging if the device is to be transported.

• All modifications of the device are forbidden for safety reasons.

• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks,

crash, etc. Using the device in an unauthorised way will void the warranty.

4. Installation

a. Lamps

• Only fit or replace a lamp when the device is unplugged from the mains.

• Let a lamp cool down before replacing it as the temperature of a lamp can reach 700°C during operation.

• When handling a halogen lamp, do not touch it with your bare hands. Use a cloth to insert or remove it.

• Do not install lamps with a higher wattage than what this device was designed for.

• Replace any deformed or damaged lamp with a lamp of the same

type (see “Technical Specifications”):

1. Open the top cover of the rear panel by unscrewing the 3 screws

marked X, Y and Z.

2. Remove the old lamp from the socket and insert the new one

tightly into the socket.

3. Adjust the lamp holder (1 ~ 1.5mm from the lens) by fine-tuning

the 3 screws marked A, B and C to get maximum light output.

4. Close the lamp compartment.

b. Lamp Adjustment

The AERON 575S lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment

may improve light performance. Strike the lamp, open the shutter and the iris. Set the dimmer intensity to

100% and focus the light on a flat surface. Centre a hot spot (the brightest part of the image) by using the 3

adjustment screws “A, B, C”. Turn one screw after another a quarter-turn clockwise or counter-clockwise .If

you cannot detect the hot spot adjust the lamp until the light is evenly distributed.

c. Adjusting the Beam Angle

The lens system can be configured in the range between 8° and 22°. To set the desired beam angle, loose the

2 adjusting screws on the lens unit and adjust the required beam angle. Tighten the adjusting screws again

and fix back the front cover.

d. Inserting / Exchanging Gobos

• Turn off the projector and let it cool down

for 10 minutes. Disconnect the device

from the mains.

• Open the top covers on the moving head

by unscrewing the screws.

• Press the borders of the fixation rings

and remove. Remove the gobo and insert

a new one. Insert the fixation ring in front

of the new gobo.

• Close the compartment.

Product specificaties

Merk:	HQ Power
Categorie:	Effect machine
Model:	VDP575MHS20FL
Kleur van het product:	Zwart
Gewicht:	32000 g
Aantal lampen:	1 lampen
Vermogen lamp:	850 W
Ingangsspanning:	230 V
Frequentie:	50 Hz
Afmetingen (B x D x H):	620 x 362 x 410 mm