Hozelock Aquaforce 15000 Handleiding

Hozelock Pomp Aquaforce 15000

Lees hieronder de 📖 handleiding in het Nederlandse voor Hozelock Aquaforce 15000 (23 pagina's) in de categorie Pomp. Deze handleiding was nuttig voor 117 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/23

www.hozelock.com

1583A

1584A

1585A

1586A

Hozelock Ltd.

Midpoint Park, Birmingham,

B76 1AB. England

Tel: +44 (0) 121 313 1122

consumer.service@hozelock.com

www.hozelock.com

43389-003

19 20 21

22 23

6000/8000 12000/15000

that the insert is the correct way round. Close

the top of the cage and secure the clips. Whilst

the insert is in use, you may need to unblock the

Strainer Cage more frequently. Once the fish or

other wildlife have grown to a sufficient size you

can then remove the insert from your pump’s cage

and return the strainer size to its maximum 10mm

size.

Using The Flow Control

The flow Control (Fig 1 - H) can vary the amount of

water entering the pump. Alternatively, it can be

used to connect a second inlet to the pump such as a

satellite filter or a skimmer. Do not use the flow control

when the pump is being used amphibiously.

1. Open the cage and remove the end cap (Fig 1 - G).

2. Close the flow control by rotating the outer part

until the arrows are aligned.

3. Firmly screw the flow control to the inlet of the

pump aligning the arrows on the flow control with

the arrow in the centre of the top of the pump

chamber (Fig 13).

4. Locate the pump into the cage. Ensure that the

slots in the outlet adaptor align with the ribs in the

lower cage and that the grip of the flow control is

on the outside of the cage (Fig 14).

5. To use as a flow control, screw the end cap to the

free end of the flow control.

6. Rotate the grip to the desired position. This varies

the opening size on the flow control. The arrow on

the grip aligns with the pointer on the outside of

the top cage.

When the pointed end of the arrow is aligned with

the pointer on the outside of the filter cage, this

indicates minimum flow. When the wide end of

the arrow is aligned with the pointer, this indicates

maximum flow (See fig 14).

7. Locate the cable into its recess (See point 6 under

Submerged Operation), close the cage lid and

secure the clips.

8. This allows you to reduce the flow of water to your

filter and control the waterfall size.

9. To use a second inlet connect a suitable length of

hose to a hosetail which has been cut to a suitable

diameter and screw to the free end of the flow

control in place of the end cap (Fig 15).

10. The other end of the hose can be connected to a

satellite filter (Fig 16) (available as a spare from

Hozelock) or to a skimmer (Fig 17).

11. By rotating the grip of the flow control, the amount

of water coming through the satellite filter or

skimmer can be varied.

Pump Assembly & Installation

- Amphibious Operation

This pump can be used amphibiously (i.e. it can be

used whilst not submerged).

WARNING! Ensure that the unit does not take in air

or run dry otherwise your pimp will be damaged.

WARNING! Always unplug or disconnect all

appliances in the pond from the electricity supply

before putting your hands in the water whilst

equipment is being installed, repaired, maintained

or handled.

NOTE: This pump does not self prime. The suction

hose and pump must be filled with water before

switching on.

1. Open the clips at either end of the strainer cage,

open the cage, and remove all the contents.

2. Unscrew the outlet adaptor from the pump outlet

and locate it into the ribs in the lower cage (Fig 18).

3. Place the pump under the surface of the water

near the side of the pond to allow water to flow

into the pumping chamber (Fig 19).

4. Cut 2 hosetails to the required size (See point 9

under Submerged Operation). Attach a suitable

length hose to each hosetail and secure with

suitable hose clips.

5. Submerge the inlet hose under the surface of the

water ensuring that the complete hose fills. Screw

the hosetail to the inlet of the pump ensuring a

watertight seal using the washer provided (Fig 20).

6. Fix the outlet hose to the pump outlet by screwing

on the hosetail. Ensure a watertight seal using the

washer provided (Fig 21).

7. Check that the pump chamber and hose are full

of water and switch on the pump. The pump can

now be removed from the water to its amphibious

operating location ensuring that the inlet end of

the hose remains submerged.

8. To prevent the pump becoming clogged, connect

the cage to the inlet end of the inlet hose using

another hosetail.

9. When using the pump amphibiously, protect the

pump from direct sunlight. Direct sunlight may

overheat the motor.

10. The ball joint is not designed to be used out of

water.

Maintenance

The Hozelock Cyprio range of Aquaforce pumps have

been designed to allow fast and easy maintenance. To

prolong the life of your pump and keep your pump in

peak condition, you should follow these maintenance

guidelines.

Caution: Always unplug or disconnect ALL appliances

in the pond from the electricity supply before putting

your hands in the water or starting maintenance.

Product specificaties

Merk:	Hozelock
Categorie:	Pomp
Model:	Aquaforce 15000
Kleur van het product:	Black, Grey
Gewicht verpakking:	5810 g
Breedte verpakking:	320 mm
Diepte verpakking:	140 mm
Hoogte verpakking:	270 mm
Vermogen:	180 W
Draaghandvat:	Ja
Correct gebruik:	Watervoorraad
Materiaal:	Metal, PVC
Maximum werkdruk:	- bar
Slangaansluiting:	Ja
AC-ingangsspanning:	230 V
AC-ingangsfrequentie:	50 Hz
Type product:	Waterpomp
Vloei-snelheid:	15000 L/u
Maximum afleveringshoogte:	- m
Diepte van de dimensie (max):	- m
Aanleverings-hoofd:	5.7 m
Graan-grootte:	40 mm
Type toevoerwaaier:	Kegelvormige toevoerwaaier