Hotpoint FF4D K Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint FF4D K (12 pagina's) in de categorie Koelkast. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
GBGBGBGBGB
REFRIGERATOR/FREEZER COMBINATION
4DB
4DX
Contents
Installation, 2-3
Positioning and connection
Description of the appliance, 4-5
Control panel
Overall view
Start-up and use, 6-7
Starting the appliance
Chiller system
Using the refrigerator to its full potential
Using the freezer to its full potential
Maintenance and care, 8
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Holiday function
Replacing the light bulb
Precautions and tips, 9
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 10
Guarantee, 11
After Sales Service, 12
Operating Instructions
English,1
GB
2
GB
Installation
Connection of the water supply
To carry this out, use the kit provided which contains all
the necessary elements for connection to the water supply.
To improve the performance of the Aqua Care, we
recommend that you fit a tap with a filter on the pipe for
the connection to the water system: in this way it will be
possible to manually interrupt the water supply during long
periods in which Aqua Care is not used.
! The water pressure inside the water system must be
between 0.8 bar and 8 bar.
! The appliance must only be connected to a water supply
suitable for drinking.
Your appliance is supplied with a 13amp fused plug that
can be plugged into a 13amp socket for immediate use.
Before using the appliance please read the instructions
below.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Replacing fuse covers:
When replacing a faulty fuse, a 13amp ASTA approved
fuse to BS 1362 should always be used and the fuse
cover re-fitted.
If the fuse cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.
Changing the plug:
Removing the plug
If your appliance has a non-rewireable moulded plug and
you should wish to remove it to add a longer cable or to
re-route the mains cable through partitions, units etc.
please ensure that either:
- The plug is replaced by a fused 13amp re-
wireable plug bearing the BSI mark of
approval.
or
- The mains cable is wired directly into a
13amp cable outlet, controlled by a
switch (in compliance with BS 5733)
which is accessible without moving the
appliance.
! Before placing your new appliance into operation please
read these operating instructions carefully. They contain
important information for safe use, for installation and for
care of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of
the appliance and any furniture above it, and at least 12 cm
between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the
refrigerator by tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to
the electricity mains. Before inserting the plug into the
electrical socket ensure the following:
 The appliance is earthed and the plug is compliant with the
law.
 The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on
the bottom left side of the fridge (e.g. 150 W).
 The voltage must be in the range between the values
indicated on the data plate located on the bottom left side
(e.g. 220-240V).
 The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it (see Assistance). Do not
use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
!The manufacturer declines any liability should these
safety measures not be observed.
GB
3
Disposing of the plug
Cut off and dispose of the supplied plug if it does not fit
your socket. The cable should be cut as close as possible
to the moulded plug.
Remove the fuse.
WARNING:
To avoid a shock hazard do not insert the discarded
plug into a socket anywhere else.
Fitting a new plug
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
Green and Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- Connect Green and Yellow wire to terminal marked
'E' or or coloured Green and Yellow.
- Connect Brown wire to terminal marked 'L' or coloured
red or brown.
- Connect Blue wire to terminal marked 'N' or coloured
Black or Blue.
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse. A 15amp plug must be protected
by a 15amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC
& 93/68/EEC


Product specificaties

Merk: Hotpoint
Categorie: Koelkast
Model: FF4D K
Apparaatplaatsing: Vrijstaand
Kleur van het product: Zwart
Ingebouwd display: LED
Breedte: 700 mm
Diepte: 740 mm
Hoogte: 1900 mm
Brutocapaciteit vriezer: 138 l
Vriescapaciteit: 8 kg/24u
Ontdooifunctie: Ja
Brutocapaciteit koelkast: 300 l
Aantal planken koelkast: 3
Bewaartijd bij stroomuitval: 12 uur
Snelvriesfunctie: Ja
Aantal sterren: 4*
Eierenrekje: Ja
Flessenrek: Ja
No Frost system: Nee
Totale brutocapaciteit: 438 l
Ingebouwde vriezer: Ja
Klimaatklasse: SN-ST
Antibacteriële functie: Ja
Ijsblokjeshouder: Ja

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint FF4D K stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Koelkast Hotpoint

Handleiding Koelkast

Nieuwste handleidingen voor Koelkast