HOLGA 135-3D Handleiding

HOLGA Fotocamera 135-3D

Lees hieronder de šŸ“– handleiding in het Nederlandse voor HOLGA 135-3D (10 pagina's) in de categorie Fotocamera. Deze handleiding was nuttig voor 72 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
1
HOLGA 135-3D
3-DIMENSIONAL PICTURE CAMERA
OPERATION INSTRUCTIONS
Welcome to owning this special, one of a kind, 3D camera!
By making resemblance to the same principle in the capture of images by the human eyes, the two
built-in lenses of the Holga 135-3D cameras will simultaneously capture two almost identical and yet
different pictures which, through the use of specially designed viewing devices (optionally
available separately), will enable the reproduction of the captured image in 3-dimensonal
photographic effects which approximate reality.
In addition, you can still take separate conventional 2D pictures one at a time with this camera.
With this 3D camera, you will cross the threshold to enter a total new world of fun and joy in taking
pictures.
Enjoy!
1. Parts of the Camera
Fig. 1 Fig. 2
(1) B-Mode Selector 1 (12)
Socket for Shutter Release Cable
(2) Focus Ring 1 (13)
Hot Shoe
(3) Lens 1 (14)
View Finder
(4) Aperture Selector 1 (15)
Film Rewind Knob
(5) Lens Cap 2 (16
)
Film Rewind Handle
(6) Focus Ring 2 (17)
Back Cover
(7) B-Mode Selector 2 (18)
View Finder Eyepiece
(8) Aperture Selector 2 (19)
Film Advance Gear
(9) Ring for Hand Strap (20)
Film Release Button
(10) Film Counter (21)
Tripod Mounting Socket
(11) Shutter Release Button
2
2. Film to Use
The camera can accommodate all 135 format films. The use of films with exposure speed
ASA 100 on sunny days and ASA 400 on cloudy days /indoor occasions is recommended.
3. Film Loading
Film Compartment Film Advance Sprockets Film Tongue ā€œ1ā€
Slot on Take-Up Spool
Fig. 3 Fig. 4 Fig. 5
(a) Grab the Film Rewind Handle to pull up the Film Rewind Knob. - the latch for the
Back Cover will be released and the Back Cover will pop open. (Fig. 3)
(b) Insert a new film roll into the Film Compartment and push the Film Rewind Knob back
to engage into the film roll. If the knob cannot be pushed back, turn it slowly until it
can be done so.
(c) Pull on the Film Tongue to pull out the film until the tip of the tongue reaches
approximately, but not beyond, the hinge for the Back Cover.
(d) Insert the tip of the Film Tongue into the slot on the Take-Up Spool. Press the film
so that the tip of the film goes into the Take-Up Spool and the film becomes more or
less flat. (Fig. 4)
(e) Turn the Film Advance Gear slightly while adjusting the Film Advance Sprockets at
the same time to enable the sprockets to engage into the holes on the two sides of the
film.
(f) Snap the Back Cover back into place.
(g) Turn the Film Advance Knob to advance the film until it cannot turn any further and
then press the Shutter Release Button.
(h) Repeat (g) again until the number ā€œ1ā€ appears in the Frame Counter (Fig. 5). The
camera is now ready for taking pictures.
4. Focusing
Although this camera is basically a fixed focus camera, it still offers four choices of object
distances. There are four symbols on the Focus Ring to make selection for the following
object distances -
3
(a)
= 1m or 3.25 ft.
(b)
= 2m or 6.50 ft.
(c)
= 6m or 20.00 ft
(d)
= 10m or 33.00 ft. or more
More precise setting for object distances can be achieved by turning the Focus Ring to
positions in between two symbols.
Focus Ring
Aperture Selector
Fig. 6
5. Choice of Aperture
By setting the Aperture Selector (Fig. 6 above), two choices are available for selection as
follows -
(a) Sunny Symbol = f/11 for use on sunny days; and
(b) Cloudy Symbol
= f/8 for use on cloudy days.
6. Picture Taking
6.1. Taking 3D Pictures
(a) Remove the covers of both lenses.
(b) Set BOTH B-Mode Selectors 1 & 2 to the ā€œNā€ position.
(c) Set BOTH Aperture Selectors 1 & 2 according to the weather/environmental
conditions :-
- Sunny symbol for sunny outdoor occasions; and
- Flash/Cloudy symbol for cloudy outdoor or insufficiently lit-up indoor
occasions.
(d) Estimate the object distance and turn BOTH Focus Rings 1 & 2 to set the object
distance accordingly.


Product specificaties

Merk: HOLGA
Categorie: Fotocamera
Model: 135-3D

Heb je hulp nodig?

Als je hulp nodig hebt met HOLGA 135-3D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Fotocamera HOLGA

HOLGA

HOLGA 120S Handleiding

13 Februari 2023
HOLGA

HOLGA 135-3D Handleiding

13 Februari 2023
HOLGA

HOLGA 120SF Handleiding

13 Februari 2023

Handleiding Fotocamera

Nieuwste handleidingen voor Fotocamera