Hoffman HF0416414 Handleiding

Hoffman Afzuigkap HF0416414

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Hoffman HF0416414 (8 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Β© 2018 nVent 89137856
Rev. K P/N 89134973
Side-Mount Filter Fans and Grilles
HF/HG Models
INSTRUCTION MANUAL
Β© 2018 nVent
- 2 - 89137856

ξ€—ξ€™
ξ€–
+)ξ€’+*0ξ€–[ξ€”ξ€™
+)ξ€’+*ξ€“ξ€˜ξ€ξ€”ξ€–ξ€ξ€ƒξ€ƒ0ξ€—[
[ξ€Œ [ξ€Œ
3XUFKDVH6HSDUDWHO\
ξ€˜
[ξ€Œ
[ξ€Œ
+)ξ€’+*0ξ€–
+)ξ€’+*ξ€“ξ€˜ξ€ξ€”ξ€–ξ€ξ€ƒξ€ƒ0ξ€—
2SWLRQDO
[ξ€Œ
2SWLRQDO
[ξ€Œ
TABLE OF CONTENTS
Installation Instructions............................................................................................3
Wire Diagrams ...........................................................................................................5
How to Read Model Numbers .................................................................................6
Filter Cleaning / Replacement .................................................................................6
Replacement Parts ...................................................................................................7
Warranty .....................................................................................................................7
Β© 2018 nVent
89137856 - 3 -
Before cutting holes in the sides of the enclosure, verify
all internal components are clear of the cutting tool to
avoid damaging installed components.
CAUTION
INSTALLATION INSTRUCTIONS
1. Apply cutout template to the side of the enclosure located as desired.
See Figure 1
2. Cutout hole in enclosure using the appropriate cutout size for the model you
purchased.
3. Deburr the cutting edge.
4. Insert fan or grille and push into opening until all four corners are snapped
and locked. See Figure 2.
5. Mounting fasteners are not required for panel or enclosure material thickness
less than .10 (2.5 mm). For panel or enclosure material thickness between .10
(2.5 mm) and .14 (3.5 mm), mounting fasteners are recommended. For panel
or enclosure material thickness greater than .14 (3.5 mm), mounting fasteners
are required in order to maintain the IP / Type 12 rating.
6. In order to install the mounting fasteners, removal of the grille is required.
Remove the grille by pulling from the top of the grille to 45Β° maximum as
shown in Figure 3 on page 4. Then pull from the bottom as shown in Figure
4 on page 4.
NOTE: The orientation β€œTop” directs the louvers downward. This is for
reference only; the assembly can be installed to orient louvers in any direction.
7. It may be necessary to drill out the mounting holes in the ξœͺlter housing. For
model HF04, use a 1/8 (3 mm) drill bit. For models HF05, HF09, HF10 and
HF13, use a 5/32 (4 mm) drill bit.
8. Torque fasteners to 20-25 in-lbs (2.3-2.8 Nm). See Figure 5 on page 4.
9. Install the grille as shown in Figure 2
10. Verify the location of the enclosure with installed ξœͺlter fan has a minimum
clearance of 7.00 (178 mm). See Figure 7 on page 4
11. Wire the ξœͺlter fan following the Wire Diagrams on page 5 for the
appropriate model being installed.
Figure 1
ξ€™
Figure 2
ξ€”

ξ€™
ξ€™


Product specificaties

Merk: Hoffman
Categorie: Afzuigkap
Model: HF0416414
Kleur van het product: Wit
Gewicht: 400 g
Breedte: 113 mm
Diepte: 93 mm
Hoogte: 112 mm
Geluidsniveau: 36 dB
Installatie compartiment breedte: 92 mm
Installatie compartiment hoogte: 92 mm
Vermogensverbruik (max): 8.5 W
Luchtstroom: 36 mΒ³/uur
Aantal: 1
Aantal ventilatoren: 1 ventilator(en)
AC-ingangsspanning: 115 V
AC-ingangsfrequentie: 50 - 60 Hz
Bedrijfstemperatuur (T-T): -10 - 55 Β°C
Ventilator diameter: - mm
Fan snelheid (max): 3250 RPM
Beschermrooster inbegrepen: Ja

Heb je hulp nodig?

Als je hulp nodig hebt met Hoffman HF0416414 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afzuigkap Hoffman

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap