Hobart 6801 Handleiding

Hobart Zaagmachine 6801

Lees hieronder de 📖 handleiding in het Nederlandse voor Hobart 6801 (12 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 82 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
FORM 34405 Rev. C (August 2011)
MODEL 6801 MEAT SAW
MODEL
6801 ML-134094
PREVIOUS MODELS COVERED BY THIS MANUAL:
6801 ML-104948
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
– 2 –
Installation, Operation, and Care of
MODEL 6801 MEAT SAW
SAVE THESE INSTRUCTIONS
GENERAL
The 6801 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant
3 HP electric motor and direct gear drive transmission. The carriage (Fig. 1) has stainless steel ball
bearings providing easy travel and dependability. The shaped front edge of the carriage is comfortable to
the operator's body even when leaned on during movement. The carriage lock is standard.
Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of
cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting
zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride
on the right "anged-end" of the carriage so you keep your hands away from the cutting edge of the blade.
For electrical specications above 250 volts, a transformer provides a 115 volt control circuit voltage.
Thermal overload protection is an option.
One long-life blade is furnished with each saw as standard equipment. This blade cannot be re-sharpened;
replacement blades are available through your local Hobart Service Ofce.
© HOBART, 1995, 2000
PL-41385-1
UPPER PULLEY COVER (SST)
COLUMN GUARD
GAUGE PL EAT
TABLE (RIGHT)
GAUGE PL E HANDLEAT
LOCK LEVER
LOWER COVER (SCRAP N)PA
LEGS
FEET
CARRIAGE LOCK
CARRI EAG
TABLE (LEFT) SAW BLADE
UPPER GUIDE AND GUARD
SWITCH KNOB
Fig. 1
– 3 –
INSTALLATION
UNPACKING AND ASSEMBLY
Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found
to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure it agrees with the specications on the machine
data plate located on the column.
Packed in a packet attached to the table compartment are the pusher plate and the gauge plate handle.
Place the pusher plate in its storage location under the carriage support (Fig. 2). Assemble the gauge
plate handle to the gauge plate support by screwing the stud into the threaded hole (Fig. 3).
LEVELING
Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side-to-
side by turning the threaded feet in or out.
PL-52107
Hand Knob
Upper Guide
and Guard
PL-41386-1
HAND KNOB
CARRIAGE
SUPPORT
SAW BLADE
CARRI EAG
PUSHER PL EAT
PL-41387-1
GAUGE PL E HANDLEAT
Fig. 2 Fig. 3
Fig. 4
Disconnect the electrical power to the machine and follow lockout / tagout
procedures.
SAW BLADE
The saw blade must be installed so the teeth point to the right and
down (Fig. 4).
UPPER GUIDE AND GUARD ASSEMBLY
When the saw is off, the hand knob (Fig. 4) can be used to raise or lower
the upper guide and guard assembly so the cutting zone is only as high
as necessary for the piece being cut. The hand knob is not loosened
during raising or lowering — it should remain tightly secure.

Product specificaties

Merk: Hobart
Categorie: Zaagmachine
Model: 6801

Heb je hulp nodig?

Als je hulp nodig hebt met Hobart 6801 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Hobart

Hobart

Hobart 6801 Handleiding

9 Augustus 2023
Hobart

Hobart 6614 Handleiding

9 Augustus 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Ozito

Ozito PXBCS-1830 Handleiding

24 December 2024
Einhell

Einhell STP 500 E Handleiding

23 December 2024
Anova

Anova E60CS Handleiding

20 December 2024
Silverline

Silverline 447132 Handleiding

19 December 2024
Silverline

Silverline 427644 Handleiding

19 December 2024
Herkules

Herkules KS 210 Profi Handleiding

17 December 2024
Total

Total TS730301 Handleiding

16 December 2024
Total

Total TJSLI8501 Handleiding

16 December 2024
Turbo-Silent

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024
Bavaria

Bavaria BJS 400 Handleiding

5 December 2024