HireTech HTW-5 Handleiding
HireTech
Behangafstomer
HTW-5
Lees hieronder de 📖 handleiding in het Nederlandse voor HireTech HTW-5 (14 pagina's) in de categorie Behangafstomer. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/14
STEAM WALLPAPER STRIPPER
MODEL HTW-5
OWNERS MANUAL & OPERATING INSTRUCTIONS
REF. 73 PART # 007716
PRINTED IN THE UK
NOVEMBER 2011 © Hiretech
ABC
NORTH AMERICAN SAFETY INSTRUCTIONS
WARNING: This steam wallpaper stripping machine must be grounded.
This steam wallpaper stripping machine shall be grounded while in use to protect the operator
from electric shock. The machine is provided with a three-conductor cord and a moulded three-
contact grounding type attachment plug to fit the proper grounding type receptacle. The Green
(or Green and Yellow) conductor in the cord is the grounding wire. Never connect this wire to
other than the grounding pin of the attachment plug.
This steam wallpaper stripping machine is provided with an attachment plug as shown in sketch
A. It is intended for use on a nominal 120 volt circuit. If a properly grounded receptacle as shown
in sketch A is not available, an adaptor as shown in sketch 'C' should be installed as shown in
sketch B if the outlet box that houses the receptacle is grounded. Be sure to fasten the grounding
tab with a metal faceplate screw.
WARNING: Steam under pressure and hot surfaces.
DO NOT remove or tamper with the steam cap when in operation. If a fault occurs allow steam
stripper to cool for a minimum of 2 minutes. Follow instructions detailed in this manual for fitting
and removing the steam cap.
ATTACHMENT PLUG SKETCH ‘C’
METAL
SCREW
COVER OF GROUNDED
OUTLET BOX SKETCH ‘B’
ADAPTER
GROUNDING
MEANSCOVER OF GROUNDED
OUTLET BOX SKETCH ‘A’
GROUNDING PIN
This manual covers machines starting from the following serial numbers;
(220/240 Volt) (excluding North America)84264
84258 (110/120 Volt) (excluding North America)
75154 (110/120 Volt) (North America)
CONTENTS
WARNING i
MAINS CABLE WIRING - PLUG i
SPARE PARTS i
SPECIFICATION 1
SAFETY 1
OPERATION 1,2
STRIPPING TECHNIQUE 2
OPERATING HINTS 2
MAINTENANCE AND SERVICING 2
FAULT FINDING 3
HTW-5 PARTS DRAWING 4
(excluding North America)
HTW-5 PARTS DRAWING 5
(North America only)
HTW-5 PARTS LIST 6
HTW-5 CIRCUIT DIAGRAMS 7
DECLARATION OF CONFORMITY 7
SERVICE & REPAIR 8
DEALER LIST 9
WARNING
For safe operation of this machine, read and understand all instructions. Look for the ‘warning/caution’ symbol.
This symbol means that if you do not follow the instructions injury can occur to the operator and
damage to the machine and work surface may result.
MAINS CABLE WIRING - PLUG
Hiretech reserves the right to make changes or improvements to it's products without prior notice.
®
i
NORTH AMERICA
BLACK
WHITE
GREEN
BRASS
TERMINAL
SILVER
TERMINAL
EU
BLUE BROWN
GREEN/
YELLOW
UNITED KINGDOM
BLUE
(N - NEUTRAL) BROWN
(L - LINE)
GREEN/YELLOW
(E - EARTH)
SPARE PARTS
Use Hiretech genuine spare parts only for service and repair. Use of non-approved parts will void the product
®
warranty. See the back cover of this manual for the terms and conditions of the Hiretech Limited Warranty.
®
Product specificaties
| Merk: | HireTech |
| Categorie: | Behangafstomer |
| Model: | HTW-5 |
Heb je hulp nodig?
Als je hulp nodig hebt met HireTech HTW-5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Behangafstomer HireTech
4 April 2024
Handleiding Behangafstomer
- Behangafstomer Toolland
- Behangafstomer Vonroc
- Behangafstomer Wagner
- Behangafstomer Black And Decker
- Behangafstomer Cocraft
- Behangafstomer Draper
- Behangafstomer Cotech
- Behangafstomer Hard Head
- Behangafstomer Challenge Xtreme
Nieuwste handleidingen voor Behangafstomer
20 Februari 2024
5 December 2023
1 Juni 2023
29 Mei 2023
28 April 2023
2 April 2023
26 Maart 2023
24 Maart 2023
21 Maart 2023
19 Maart 2023