Hinkley Lighting Carlton 4771SL Handleiding

Hinkley Lighting Verlichting Carlton 4771SL

Lees hieronder de 📖 handleiding in het Nederlandse voor Hinkley Lighting Carlton 4771SL (3 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
assembly instructions
Item No. 4771
1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.
*** The construction of this fixture will be accomplished by first assembling the
main body of the fixture, making all necessary electrical connections, hanging
the fixture from the ceiling, and then installing the shade and crystals.
4771
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Drawing 2 - Fixture Assembly
01.01.13
1. Rotate arms until they are approximately degrees apart - see(A) 90 Drawing 1
and 3.
2. Fixture can be installed at this time.
A A
A
A
90º
Drawing 1 - Fixture Assembly
s r reta t he
33000 Pin Oak P ark w ay, Avon Lak e , OH 4 4 0 1 2 800.446.5 5 3 9 / 440.653.5 5 0 0 h i n k leyl ighting.com
Drawing 3 - Fixture Mounting
Drawing 2 - Strap Detail
J
B
AG
D
E
C
1. Prepare mounting strap for mounting by installing screws into mounting (B) (A)
plate - see .(B) Drawing 2
• Be sure the holes into which the screws are threaded match the spacing of holes (C)
in the canopy - see .(1) Drawings 2 and 3
2. Attach mounting plate to junction box , using screws provided and slip (B) (J) (G)
supply wires through large center hole.
Make electrical connections from supply wire to fixture lead wires. Refer to instruction
sheet and follow all instructions to make all necessary wiring connections. (I.S. 18)
Then return back to this sheet to continue installation of this fixture.
5
51. Hang the fixture by slipping canopy over screws and hold in position - see (D) (B)
Drawings 2 and 3.
2. Thread ball knobs onto end of screws and tighten to secure fixture to ceiling.(E) (B)
61. To install shade , slip shade over fixture installed fixture body and place tab (1) (T)
on top of crossbar and align holes in tab with holes in crossbar -see .(S) Drawing 4
2. Slip screw through holes in tab and crossbar and thread on ball knob to (2) (3)
secure shade to fixture.
3. See page 2 of instruction for crystal installation.
page 1
12
3
assembly instructions
Item No. 4771
4771
s r reta t he page 2
1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.
01.01.13
1. To complete assembly, first thread bottom finial with crystal attached onto (3) (F)
bottom of fixture - see .Drawing 2
2. Proceed to attach crystals using as a reference quide. If a crystal must Drawing 2
be replaced, please use the part no.s provided below the crystal drawings when
ordering.
3. The crystals are referenced with the quantity ( Ex. ? x 6) required following the
letter.
R4771CRY-C R4771CRY-BR4771CRY-A
B CA
R4772CRY-C
D
CRYSTAL INDENTIFICATION
A X 4
A X 4
A X 4 B X 4
C X 4
D ATTACHED
TO FINIAL
33000 P in Oak P ark w ay Avon Lake, OH 44012 8 0 0 .4 4 6 .5 5 3 9 / 4 4 0 .6 5 3 .5 5 0 0 hinkl eyli g h t ing.com
I.S. 18 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
wiring instructions
Indoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth, unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see .Drawings 1 or 2
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Please refer to the below to complete all grounding instructions
electrical connections.
Outdoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see . Drawings 2 or 3
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a
fixture mounting platform specially.
4. Please refer to the below to complete all grounding instructions
electrical connections.
grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (typically copper or green plastic coated) to the fixture mounting strap (E) (1)
with the ground screw - see . (2) Drawing 1
Note: On straps for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (typically copper or green plastic coated) under the (E)
head of the ground screw on fixture mounting strap and connect to the (2) (1)
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - see .Drawing 2
Post-Mount Fixtures
Connect fixture ground wire (typically copper or green plastic coated) to power (E)
supply ground with appropriately sized twist-on connector inside post. Cover open
end of connector with silicone sealant to form a watertight seal - see .Drawing 3
Drawing 1 - Flush Mount
Drawing 2 - Chain Hung
supply wire
fixture leads
twist-on
connectors
Drawing 3 - Post-Mount
twist-on
connectors
1
A CC
B D
supply wire
fixture leads
A C
B D
1
2
supply wire
fixture leads
A C
B D
twist-on
connectors
E
2
E
E
E
E
I.S. 18

Product specificaties

Merk: Hinkley Lighting
Categorie: Verlichting
Model: Carlton 4771SL

Heb je hulp nodig?

Als je hulp nodig hebt met Hinkley Lighting Carlton 4771SL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Verlichting Hinkley Lighting

Hinkley Lighting

Hinkley Lighting Yale 13302BK Handleiding

11 December 2024
Hinkley Lighting

Hinkley Lighting 1542BZ Handleiding

11 December 2024
Hinkley Lighting

Hinkley Lighting Winton 5236BN Handleiding

11 December 2024
Hinkley Lighting

Hinkley Lighting Axis 41709BK Handleiding

3 November 2024
Hinkley Lighting

Hinkley Lighting Halo 42008BK Handleiding

3 November 2024
Hinkley Lighting

Hinkley Lighting Graham 38893BK Handleiding

3 November 2024
Hinkley Lighting

Hinkley Lighting Jules 53241BN Handleiding

3 November 2024
Hinkley Lighting

Hinkley Lighting Harbor 2573AR Handleiding

3 November 2024
Hinkley Lighting

Hinkley Lighting Hadley 3302AN Handleiding

3 November 2024
Hinkley Lighting

Hinkley Lighting Monte 28881BK Handleiding

3 November 2024

Handleiding Verlichting

Nieuwste handleidingen voor Verlichting

LumenRadio

LumenRadio CRMX Galileo MAX Handleiding

21 December 2024
Showtec

Showtec Performer Fresnel 2200 DDT Handleiding

21 December 2024
Showtec

Showtec AirDrive 2.4 IP Handleiding

21 December 2024
Bosch

Bosch FSN 1400 Set Professional Handleiding

21 December 2024
Neewer

Neewer VL66C Handleiding

18 December 2024
American DJ

American DJ ENCORE LB15IP Handleiding

18 December 2024
American DJ

American DJ ENCORE LP12IP Handleiding

18 December 2024
Wiesenfield

Wiesenfield UNI-LP-100 Handleiding

17 December 2024
Cateye

Cateye Wearable mini SL-WA10 Handleiding

16 December 2024
Cateye

Cateye Volt50 HL-EL460RC-REAR Handleiding

16 December 2024