Hikvision DS-2CE15A2P-IR Handleiding

Hikvision Bewakingscamera DS-2CE15A2P-IR

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE15A2P-IR (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

1 Introduction

1.1 Product Features

This series of camera adopts new generation

sensor with high sensitivity and advanced

circuit design technology. It features high

resolution, low image distortion and low noise

features, etc., which makes it suitable for

surveillance system and image processing

system.

●High-performance sensor and high resolution

bring high-quality image

●IR LED enables the day/night surveillance

●IR cut filter auto switch

●ATW brings high color rendition

●Ingress protection:IP66

1.2 Overview

Figure 1-1 Overview of Type CameraⅠ

Figure 1-2 Overview of Type CameraⅡ

Figure 1-3 Overview of Type CameraⅢ

Figure 1-4 Overview of Type CameraⅣ

2 Installation

Before you start :

●Make sure that all the related equipment is

power-off during the installation.

●Check the specification of the products for the

installation environment.

●Check whether the power supply is matched

with your AC outlet to avoid damage.

●If the product does not function properly, please

contact your dealer or the nearest service

center. Do not disassemble the camera for

repair or maintenance by yourself .

●Please make sure that the ceiling or the wall

is strong enough to withstand 3 times the

weight of the camera.

Bullet Camera

User Manual

www.hikvision.com

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0200001030603

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested

and found to comply with the limits for a digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial

environment. This equipment generates, uses,

and can radiate radio frequency energy and, if

not installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications. Operation

of this equipment in a residential area is likely to

cause harmful interference in which case the user

will be required to correct the interference at his

own expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

This product and - if applicable -

the supplied accessories too are

marked with "CE" and comply

therefore with the applicable harmonized

European standards listed under the Low Voltage

Directive 2006/95/EC, the EMC Directive 2004/

108/EC, the RoHS Directive 2011/65/EU.

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see:www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery

that cannot be disposed of as

unsorted municipal waste in the

European Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

2012/19/EC (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

IR LED

Lens

Sun Shield Adjustable Screw Power Cable

Video Cable

IR LED

Lens

Sun Shield Adjustable Screw Power Cable

Video Cable

Mounting Base

Sun S hie ld

Len s

IR LED

Power C abl e

Vid eo Ca ble

Mounting Base

Video Cable

Power Cable

Sun Shield

Lens

IR LED

UD.6L0201D1104A01

Model

DS-2CE1512P(N)-IR, DS-2CE1582P(N)-IR

DS-2CE15A2P(N)-IR,DS-2CE15C2P(N)-IR

DS-2CE1582P(N)-IRP,DS-2CE15A2P(N)-IRP

Ⅰ

Type

DS-2CE1682P(N)-IT1,

DS-2CE1682P(N)-IT3

DS-2CE16A2P(N)-IT1

DS-2CE16C2P(N)-IT1,

DS-2CE16A2P(N)-IT3,DS-2CE16C2P(N)-IT3

DS-2CE1682P(N)-IT5,

DS-2CE16C2P(N)-IT5

DS-2CE16A2P(N)-IT5

DS-2CE1582P(N)-VFIR3,DS-2CE15A2P(N)-VFIR3

DS-2CE15C2P(N)-VFIR3

Ⅱ

Ⅲ

Ⅳ

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Hammer the supplied plastic expansion bolt into

the screw holes.

3.Route the cables to the cable hole and connect

the corresponding power cable and video cable.

4.Fix the camera to the ceiling with the supplied

screws.

Figure 2-2 Fix the Camera to the Ceiling

5.Adjust the surveillance angle.

1).Loosen No.3 adjusting screw to adjust the

panning position 0 ~ 360 (.

2).Tighten No.3 adjusting screw.

3).Loosen the No.2 adjusting screw to adjust the

tilting position 0 ~ 90( ° °).

4).Tighten No.2 adjusting screw.

5).Loosen No.1 adjusting screw to adjust the

azimuth angle of the image 0 ~ 360( ° °).

6).Tighten No.1 adjusting screw.

° °)

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the drill template.

2.Hammer the supplied plastic expansion bolt into

the screw holes.

Steps:

1.Drill the screws holes and the cable hole on the

ceiling according to the supplied drill template.

2.Hammer the supplied plastic expansion bolt

into the screw holes.

Figure 2-8 Fix the Camera to the Ceiling

3.Route the cables to the cable hole and connect

the corresponding cables.

4.Fix the camera to the ceiling with the supplied

screws.

Figure 2-9 3-axis Adjustment

6.Adjust the zoom and the focus.

1).Output the image to the monitor.

2).Push forward to remove the adjusting sheet

located on the bottom of the camera. See

figure below.

3).Insert the removed adjusting sheet to zoom

slot and focus slot to adjust the zoom and the

focus.

4).Put the adjusting sheet back after the

adjustment is done.

2.4 Power Supply

Figure 2-11 The Powe Cable & the Video Cable

Note:

Please make sure that the power adapter is

compatible with the camera, and the standard

power supply is 12V DC. Please refer to the

technical specification for more information.

Figure 2-7 Drill Template

Figure 2-1 Drill Template Figure 2-4 Drill Template

Figure 2-5 Fix the Camera to the Wall

Figure 2-6 3-axis Adjustment

Figure 2-10 Focus and Zoom Adjustment

Figure 2-3 3-axis Adjustment

90°

360°

Ceiling Mounting

No.2 Screw Hole

for Mounting

Base

No.1 Screw Hole

for Bracket

4.Fix the camera to the wall with the supplied

screws.

5.Adjust the surveillance angle.

1).Loosen No.3 adjusting screw to adjust the

panning position (0° ).

2).Tighten No.3 adjusting screw.

3).Loosen No.2 adjusting screw to adjust the

tilting position (0 ~ 90 )° ° .

4).Tighten No.2 adjusting screw.

5).Loosen No.1 adjusting screw to adjust the

azimuth angle of the image (0 ~ 360° °).

6).Tighten No.1 adjusting screw.

~ 360°

5. Adjust the surveillance angle.

1). Loosen No.3 adjusting screw to adjust the pan

position ( .

3). Loosen No.2 adjusting screw to adjust the

tilting position( ).

5). Loosen No.1 adjusting screw to adjust the

rotation position .

0 ~ 360 )° °

2).Tighten No.3 adjusting screw.

0 ~ 90° °

4).Tighten No.2 adjusting screw.

( ° °)0 ~ 360

6).Tighten No.1 adjusting screw.

2.3 Ceiling Mounting for Type IV

Camera

2.2 W Mounting for Type IIall / III

Camera

2.1 Ceiling Mounting for Type I

Camera

360°

90°

Focus

Zoom

Adjusting Sheet

3.Route the cables to the cable hole and connect

the corresponding power cable and video cable

Adjusting Screw

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE15A2P-IR
Kleur van het product:	Wit
Gewicht:	360 g
Breedte:	149.5 mm
Soort:	CCTV-bewakingscamera
Internationale veiligheidscode (IP):	IP66
Vormfactor:	Rond
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Bureau/muur
Maximum resolutie:	976 x 496 Pixels
Diameter:	70 mm
Stroomuitvoer (volt):	+12V
Minimale belichting:	0.1 Lux
Nachtvisie:	Ja
LED-type:	IR
Vaste focale lengte:	2.8 mm
Vermogensverbruik (max):	1.8 W
Formaat analoog signaal:	PAL
Omvang optische sensor:	1/3 "
Type beeldsensor:	DIS
Camera sluitertijd:	1/50 - 1/100000 s
Composiet video-uitgang:	1
Signaal/ruis-verhouding:	62 dB
Power over Ethernet (PoE):	Nee
Draaihoek:	360 °
Aantal TV lijnen:	700
Pan bereik:	0 - 360 °
Dag/nacht modus:	Ja
Nachtkijker afstand:	20 m
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bereik kantelhoek:	0 - 90 °