Hikoki SAY-150A Handleiding
Hikoki
Schuurmachine
SAY-150A
Lees hieronder de đź“– handleiding in het Nederlandse voor Hikoki SAY-150A (9 pagina's) in de categorie Schuurmachine. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/9
Rotary Orbital Sander
Model SAY – 150A
Handling instructions
Note:
Before using this Electric Power Tool, carefully read through these
HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available
as an important reference when using this power tool.
2
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while operating
a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded)
power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool.
Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts.
Loose clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used.
Use of dust collection can reduce dust related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed.
Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of children and
infirm persons.
3
SAFETY WARNINGS COMMON FOR
SANDING OR POLISHING OPERATIONS
a) This power tool is intended to function as a sander
or polisher tool. Read all safety warnings,
instructions, illustrations and specifications provided
with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
b) Operations such as grinding, wire brushing or
cutting-off are not recommended to be performed
with this power tool.
Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed
can break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the spindle
of the power tool.
Accessories with arbour holes that do not match
the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause
loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart
during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debris generated by various operations. The
dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing
loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.
j) Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
shock the operator.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the
spinning accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and
pull the power tool out of your control.
m) Do not run the power tool while carrying it at your
side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your
body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
o) Do not operate the power tool near flammable
materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad or any other accessory. Pinching
or snagging causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power tool to be
forced in the direction opposite of the accessory’s rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either
jump toward or away from the operator, depending on
direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite
to the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Product specificaties
| Merk: | Hikoki |
| Categorie: | Schuurmachine |
| Model: | SAY-150A |
Heb je hulp nodig?
Als je hulp nodig hebt met Hikoki SAY-150A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schuurmachine Hikoki
10 December 2024
19 November 2023
29 Augustus 2023
3 Augustus 2023
3 Augustus 2023
25 April 2023
10 April 2023
17 Maart 2023
17 Februari 2023
7 December 2022
Handleiding Schuurmachine
- Schuurmachine Bosch
- Schuurmachine AEG
- Schuurmachine DeWalt
- Schuurmachine Arendo
- Schuurmachine Batavia
- Schuurmachine Bavaria
- Schuurmachine Black Decker
- Schuurmachine Bort
- Schuurmachine Bruder Mannesmann
- Schuurmachine Dremel
- Schuurmachine Duro
- Schuurmachine Duro Pro
- Schuurmachine Einhell
- Schuurmachine Elu
- Schuurmachine Fein
- Schuurmachine Ferm
- Schuurmachine Festool
- Schuurmachine Flex
- Schuurmachine Gamma
- Schuurmachine Gastroback
- Schuurmachine Global
- Schuurmachine Gude
- Schuurmachine Hitachi
- Schuurmachine Holzmann
- Schuurmachine Hyundai
- Schuurmachine Kinzo
- Schuurmachine Kress
- Schuurmachine Maestro
- Schuurmachine Makita
- Schuurmachine Maktec
- Schuurmachine Matrix
- Schuurmachine Max
- Schuurmachine Metabo
- Schuurmachine Milwaukee
- Schuurmachine Parkside
- Schuurmachine Powerplus
- Schuurmachine Protool
- Schuurmachine Rupes
- Schuurmachine Ryobi
- Schuurmachine Scheppach
- Schuurmachine Silverline
- Schuurmachine Skil
- Schuurmachine Stanley
- Schuurmachine Stomer
- Schuurmachine Toledo
- Schuurmachine Toolcraft
- Schuurmachine Topcraft
- Schuurmachine Trotec
- Schuurmachine Varo
- Schuurmachine Vonroc
- Schuurmachine Westfalia
- Schuurmachine Workzone
- Schuurmachine Worx
- Schuurmachine Ozito
- Schuurmachine Black And Decker
- Schuurmachine Cocraft
- Schuurmachine Meec Tools
- Schuurmachine Far Tools
- Schuurmachine Hilti
- Schuurmachine Power Craft
- Schuurmachine Tacklife
- Schuurmachine Truper
- Schuurmachine Fieldmann
- Schuurmachine Mafell
- Schuurmachine Proxxon
- Schuurmachine Biltema
- Schuurmachine Porter-Cable
- Schuurmachine Probuilder
- Schuurmachine Dedra
- Schuurmachine RIDGID
- Schuurmachine Tryton
- Schuurmachine Herkules
- Schuurmachine Craftsman
- Schuurmachine Rikon
- Schuurmachine Alpha Tools
- Schuurmachine Hazet
- Schuurmachine Stalco
- Schuurmachine Powertec
- Schuurmachine Meister Craft
- Schuurmachine King Craft
- Schuurmachine Toolson
- Schuurmachine Wagner SprayTech
- Schuurmachine Einhell Bavaria
- Schuurmachine McKenzie
- Schuurmachine Prowork
- Schuurmachine Proviel
- Schuurmachine Ribimex
- Schuurmachine FIXIT
- Schuurmachine Ergotools Pattfield
- Schuurmachine THUN
- Schuurmachine Bavaria By Einhell
- Schuurmachine Pevec
- Schuurmachine Handwerk
- Schuurmachine TAURUS Titanium
Nieuwste handleidingen voor Schuurmachine
23 December 2024
8 December 2024
5 December 2024
5 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024