Havis C-VS-1300-TBZ Handleiding

Havis Carkit C-VS-1300-TBZ

Lees hieronder de 📖 handleiding in het Nederlandse voor Havis C-VS-1300-TBZ (4 pagina's) in de categorie Carkit. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
INSTALL INSTRUCTIONS C- -1300-TBZ VS
VEHICLE SPECIFIC CONSOLE
2002-2009 CHEVROLET TRAILBLAZER
TOOLS REQUIRED:
Phillips screwdriver
T-15 Torx driver
T-20 Torx driver
7/16 wrench
Ratchet wrench
7/16” socket
15mm socket
Jig Saw or plastic cutting tool
Eye goggles
HARDWARE:
QTY DESCRIPTION PART #
1 Trailblazer vehicle specific console C- -1300-TBZ- VS H
1 Bail bracket C- B1
1 Rear hump bracket set C-B27
1 Duct block off plate CM001516
2 CM93594 Side “L” brackets
1 Console hardware kit C- HK
1 Torx screw kit C- -1 HK
1 #10x1/2 PPHSMS (Block off plate screw) GSM33194
Always!
Read all instructions before installing any Havis, Inc. products.
Disconnect the vehicle battery. Removing seat bolts on some vehicles may give the vehicles
computer a false reading, causing a warning light on the instrument cluster. This requires the
vehi cles’ computer to be reset with a vehicle diagnostics tool.
Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
Use only hardware provided with install kit.
C- -1300-TBZ_INST_6-09.docx6-VS 09
2
Remove six phillips screws that hold
inner storage pocket. Remove
storage pocket and arm rest
assembly.
Remove main console screws.
Unplug wires for rear controls.
Remove shift lever “T” knob.
(T15 Torx)
Measure approximately 3 ½” back
from shift lever boot.
Mark Measurement with tape.
Position shift lever in drive or
further back. Remove entire
console assembly.
Note: In order to remove console,
you must reach up inside the shifter
boot and disconnect the traction
control plug.
Remove front trim to aid in running
additional wiring.
C- -1300-TBZ_INST_6-09.docx6-VS 09
3
Extend cut line on console sides.
Carefully cut off back console
section. (Jig saw, Air saw, Dremel
or Air drill)
Carefully reinstall front console
section.
(Reattach Traction Control Plug)
Reattach shift lever “T” handle.
Remove inboard rear seat nuts.
(15mm) Place new rear hump
brackets on seat studs under seat
brackets.
Attach bail bracket onto rear hump
brackets with ¼ x ¾ bolts.
Note: You may need to bend hump
brackets slightly forward.
Place duct block off plate in duct
opening and screw down with #10 x
½” sheet metal screw.
Attach “L” mount brackets to new
console lower side tracks with ¼ x
½ bolts and washers.
**Leave loose to aid in positioning.
Place new console between seats
and position “L” mount brackets
onto OEM bracket. Attach with
1/4” x 3/4” bolts.
Position console housing as desired
and tighten all mount hardware.
**Check shift lever in rear position.


Product specificaties

Merk: Havis
Categorie: Carkit
Model: C-VS-1300-TBZ
Kleur van het product: Zwart
Compatibele producten: 2002-2009 Chevrolet Trailblazer

Heb je hulp nodig?

Als je hulp nodig hebt met Havis C-VS-1300-TBZ stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Carkit Havis

Handleiding Carkit

Nieuwste handleidingen voor Carkit

Metra

Metra 99-7339B Handleiding

17 November 2024
Scosche

Scosche HA1714B Handleiding

17 November 2024
Metra

Metra 99-7345B Handleiding

17 November 2024
Metra

Metra AX-ADCT4 Handleiding

17 November 2024
Metra

Metra 95-7883HG Handleiding

17 November 2024
Metra

Metra 95-5026 Handleiding

17 November 2024
Metra

Metra 99-7367HG Handleiding

23 Augustus 2024
Metra

Metra 99-8223 Handleiding

23 Augustus 2024