Havis C-MAP-S Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Havis C-MAP-S (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Gooseneck Map Light
Installation Instructions
Warning: Please read all instructions and warnings prior to installation of the Gooseneck Map Light.
TOOLS REQUIRED:
Phillips Screw Driver
Wire Cutter
HARDWARE: (Supplied in Kit)
Qty. Description Qty. Description
2 #6 Machine Screw 2 #6 Split Lock Washer
2 #6 Thread Forming Screw 2 #6 Flat Washer
INSTALLATION:
1. Mounting:
A drill template is provided on the back of this instruction sheet. Detach the
template, position it on the desired location for installation, and mark drill locations.
Caution: Before drilling holes, ensure that the mounting surfaces are clear and that the
screws will not damage the internal parts of the console or vehicle.
Caution: Ensure that the Gooseneck Map Light is installed in areas recommended by the
vehicle manufacturer—outside of the airbag zone.
Drill the mounting holes.
Remove the template prior to installing the fixture. Secure the base of the fixture in
position using the supplied machine screws and washers.
The supplied super clip may be used to secure the gooseneck in position if desired.
Caution: Thread forming screws are supplied for alternate installations requiring the fixture to
be mounted from above. If the fixture needs to be disassembled for such installation, please
note that this will void your warranty.
2. Wiring:
Connect the black lead to the vehicle chassis (Ground.)
Connect the red lead to power.
Note: It is recommended to install an in-line fuse holder and 1 Amp fuse on the red (hot) lead.
Test the light for proper operation.
C-MAP_INST_6-09
Caution: The Gooseneck Map Light uses a halogen bulb—It can be VERY HOT!
Do not touch the bulb or fixture shroud when it is hot.
3. Operation:
Power is supplied through a dimmer switch. Turn the knob clockwise to turn on the
light and increase brightness, and counterclockwise to dim or turn off power.
Caution: Always turn the dimmer knob gently. Do not force the knob to turn once it stops.
The fixture head has an integral red lens. If desired, slide the lens over the lamp for
red light, or slide it toward the stem for white light.
Note: To avoid leaving fingerprints on the lens, use only the tab on the edge of the red lens to
slide it.
4. Troubleshooting:
In the event of improper operation, first check that the dimmer switch is turned all the
way on by gently rotating the knob clockwise until it stops.
Second, check the bulb and replace it if it is burned out.
Third, check the fuse (if installed) and replace it if necessary.
Finally, use a voltmeter to ensure that the fixture is receiving adequate power. The
light requires nominally 12 VDC for correct operation. Correct any faults found.
REPLACEMENT PARTS:
Part # Description
CM93745 Lamp, 5 Watt, Halogen
TEMPLATE:
Bulb
Dimmer
+12 VDC
Power 1A Fuse
(Recommended)
User-Supplied
Connector
(Optional)
Ground
HOT - RED
COMMON - BLACK
Note:
Fuse, fuse holder, and connector are
not supplied by Havis-Shields.
WIRING DIAGRAM:
0.16 (5/32” Drill)
Mounting Holes
0.50 (1/2” Drill)
Wireway
1-23/32 21/32
Cli
p
Here
Cli
p
Here


Product specificaties

Merk: Havis
Categorie: Niet gecategoriseerd
Model: C-MAP-S

Heb je hulp nodig?

Als je hulp nodig hebt met Havis C-MAP-S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Havis

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd