Havis C-HDM-186 Handleiding

Havis Niet gecategoriseerd C-HDM-186

Lees hieronder de 📖 handleiding in het Nederlandse voor Havis C-HDM-186 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
A-
GUIDE RING BUSHING REMOVAL
WE STRONGLY RECOMMEND NOT TO REMOVE THE
GUIDE RING BUSHING, BUT IF REMOVAL OF INNER POLE
IS DESIRED - FOLLOW THIS SIMPLE REMOVAL
INSTRUCTION
INSERT MAXIMUM 1" DIAMETER OBJECT WITH
1.
SUFFICIENT LENGTH AND DROP INSIDE INNER POLE.
MAKE SURE NOTHING PREVENTS GUIDE RING
2.
BUSHING FROM BEING EJECTED UNDERNEATH. HIT
WITH A HAMMER TO FORCE THE GUIDE RING
BUSHING OUT.
7/8" - 1"
DIAMETER
OBJECT
SUPPORT ARM
(OPTIONAL)
B -
INSTALL SPIDER COLLAR (OPTIONAL
COMES WITH C-HDM-401 & 403)
IF MOUNTING THE SPIDER COLLAR TO THE INNER
1.
POLE USE CM003406 REDUCING BUSHING. SPREAD
AND SNAP OVER THE INNER POLE.
LOOSELY ATTACH SPIDER COLLAR TO THE OUTER
2.
POLE OR CM003406. DO NOT MOUNT SPIDER
COLLAR ABOVE OUTER POLE HORIZONTAL CUT.
SPIDER MUST BE
BELOW THIS SLOT
ON THE OUTER POLE
C -
INSTALL OPTIONAL C-HDM-416
IF MOUNTING C-HDM-416 TO THE INNER POLE USE
1.
CM003406. SPREAD THE PIECE AND IT SHOULD SNAP
OVER THE INNER POLE.
ATTACH C-PM-101 TO CLAMP ASSEMBLY USING
2.
LONG CARRIAGE BOLTS INSERTED THROUGH THE
PRINTER AND ONE PIECE OF EXTRUSION.
ATTACH POLE CLAMP TO THE OUTER POLE OR
3.
CM003406. AFFIX SECOND PIECE OF EXTRUSION
AROUND POLE AND LOOSELY TIGHTEN THE
HARDWARE. DO NOT MOUNT CLAMP ABOVE
OUTER POLE HORIZONTAL CUT.
CM003406 REDUCING
BUSHING IS NECESSARY
IF MOUNTING TO
THE INNER POLE.
(USE ONLY ON FIXED
HEIGHT POLES)
C-PM-101
SOLD SEPARATELY
D-
INSTALL GAS SHOCK (OPTIONAL)
(SKIP IF GAS SHOCK IS NOT IN USE)
1.
UNSCREW SMALL PLASTIC DISC FROM SHOCK
2.
INSERT GAS SHOCK ASSEMBLY UPWARD FROM
THE BOTTOM OF HDM POLE ASSEMBLY WITH GAS
SHOCK'S ROD FACING DOWNWARD. GAS
SHOCK WILL SANDWICH BETWEEN MOUNTING
BASE C-HDM-100 SERIES (NOT SHOWN) AND
ACTION ADAPTER C-HDM-300 SERIES (NOT
SHOWN).
ONCE GAS SHOCK SITS PROUD OF THE INNER
3.
POLE REATTACH SMALL PLASTIC DISC
GAS SHOCK
(OPTIONAL)
E -
INSTALL C-HDM-409 OPTIONAL
& COLLAR CLAMP ALIGNMENT
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE
1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE C-HDM-409.
2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER
3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.
4.
F -
INSTALL C-HDM-410-412 OPTIONAL
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE
1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE OFFSET.
2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER
3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.
4.
45°
MAX.
45°
MAX
SLOTS IN TUBE
AND CLAMP
ALIGNED
HAMMER
PROJECT #
REV.
DESCRIPTION
DATE
BY
CHECKED BY
1765
3-13
REVISION DATE CORRECTED TO PT895 DOCUMENTED CHANGE.
NO OTHER CHANGES
8/5/2014
KDAVIS
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 1 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): 8.362
TITLE:
DWG. NO.
C-HDM_INST
REV
A
3-13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES
C-HDM-204 SHOWN
STANDARD FLAT SURFACE
MOUNTING
FOR FLAT SURFACE MOUNTING OF C-HDM-
204, 205, 212, 213, 214, 215, 216 AND 217
(INCLUDING HAVIS CONSOLES WHICH DO
NOT HAVE HOLES PRE-DRILLED)
POSITION POLE MOUNT IN DESIRED
1.
LOCATION
MARK AND DRILL 1/4" HOLES INTO THE
2.
MOUNTING SURFACE (SEE NOTES FOR
DRILLING)
THROUGH-BOLT USING 1/4" HARDWARE
3.
PROVIDED WITH THE MOUNT OR
EQUIVALENT HARDWARE IF
NECESSARY.
C-HDM-204 SHOWN
STANDARD CONSOLE SIDE
MOUNTING
FOR CONSOLE SIDE MOUNTING OF C-
HDM-204, 205, 212, 213, 214, 215, 216 AND
217 (WHERE CONSOLE HAS PRE-INSTALLED
NUTS IN CONSOLE RAIL)
TO ATTACH C-HDM-204, 205, 214, 215
1.
LOOSEN THE RETAINING SET SCREW TO
2.
ALLOW THE NUTS TO BE POSITIONED AS
DESIRED IN THE TRACK.
LINE UP THE MOUNT WITH THE NUTS IN
3.
THE CONSOLE,
ATTACH USING HARDWARE
4.
PROVIDED WITH THE MOUNT, OR
EQUIVALENT 1/4-20 X 1/2" LONG
(MAX.) BOLTS AND FLAT WASHERS.
C-HDM-204 SHOWN
PRE-DRILL;ED CONSOLE SIDE
MOUNTING
FOR CONSOLE SIDE MOUNTING OF C-
HDM-204, 205, 212, 213, 214, 215, 216 AND
217 (WHERE CONSOLE HAS PRE-INSTALLED
NUTS IN CONSOLE RAIL)
TO ATTACH C-HDM-204, 205, 214, 215
1.
LINE UP THE MOUNT WITH THE
2.
PREDRILLED HOLES IN THE CONSOLE,
ATTACH USING HARDWARE
3.
PROVIDED WITH THE MOUNT, OR
EQUIVALENT 1/4-20 BOLTS.
DEPENDING ON THE DESIRED
4.
POSITION, HOLES MAY NEED TO BE
DRILLED, OR ONE (1) BOLT CAN USE
THE NUT TRACK WITH A 1/4-20 X 1/2"
LONG BOLT.
FOR VEHICLE MOUNTING THAT REQUIRES DRILLING
INSPECT ALL AREAS BEFORE DOING ANY DRILLING
1.
ENSURE NO SERIOUS DAMAGE HAPPENS TO THE
VEHICLE.
SECURE THE MOUNT WITH SUPPLIED HARDWARE KIT.
2.
NOTE:
MOST C-VS (VEHICLE SPECIFIC)
SERIES CONSOLES HAVE HOLES FOR
AN HDM-204 OR 214 PRE-DRILLED.
IF ANOTHER LOCATION IS DESIRED,
HOLES MAY NEED TO BE DRILLED
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 2 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): 0.00
TITLE:
DWG. NO.
C-HDM_INST
REV
A
3-13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES
D-
C-HDM-417 VERTICAL
PRINTER MOUNT SHOWN
WITH C-PM-101 ATTACHED
E-
ATTACHING THE SHAFT STOP
COLLAR THAT COMES WITH
TELESCOPING POLE WITH HANDLE
SLIDE THE INNER POLE TO THE DESIRED HEIGHT.
1.
ATTACH THE SHAFT COLLAR USING THE HARDWARE
2.
PROVIDED.
INNER POLE SHOULD NOW SPIN FREELY WHILE
3.
MAINTAINING THE DESIRED HEIGHT.
F-
EXAMPLE OF A FINISHED ASSEMBLY
THE ABOVE ASSEMBLY INCLUDES A C-HDM-102, C-
1.
HDM-202, C-MD-102, C-HDM-403, C-HDM-404(2X)
B-
C-HDM-401 SUPPORT ARM
LOOSELY ATTACH SPIDER (CLAMP) COLLAR TO
1.
POLE WITH HARDWARE SUPPLIED (IF NOT ALREADY
ATTACHED). POSITION AS DESIRED AND TIGHTEN
HARDWARE.
LOOSELY ATTACH C-HDM-401 USING HARDWARE
2.
PROVIDED.
FIND A SUITABLE LOCATION TO ATTACH THE OTHER
3.
END OF THE SUPPORT ARM. SOME VEHICLES HAVE
HOLES UNDER THE DASH OR OEM HARDWARE THAT
CAN BE UTILISED. LOOSELY ATTACH TAB PROVIDED.
EXTEND THE ARM ATTACHING THE TAB TO THE
4.
SUPPORT ARM WITH THE HARDWARE PROVIDED.
TIGHTEN ALL HARDWARE.
5.
A-
C-HDM-403 HORIZONTAL PRINTER
MOUNT
LOOSELY ATTACH SPIDER (CLAMP) COLLAR TO
1.
POLE WITH HARDWARE SUPPLIED (IF NOT
ALREADY ATTACHED). POSITION AS DESIRED
AND TIGHTEN HARDWARE.
ATTACH C-HDM-403 PLATE USING HARDWARE
2.
PROVIDED. AVOID TIGHTENING SCREWS IF AN
OFFSET ARM IS TO BE ADDED.
ATTACH DESIRED ITEM TO SHELF BRACKET.
3.
THE C-HDM-403 WORKS VERY WELL IF THERE IS
4.
NO CENTER CONSOLE. SPACE IS VERY LIMITED
AND WILL CAUSE LACK OF LEG ROOM IF THE
VEHICLE DOES HAVE A CENTER CONSOLE.
C-
C-HDM-404 SUPPORT ARM
THE C-HDM-404 IS PRIMARILY USED FOR UNIVERSAL
1.
FLOOR MOUNTS WHEN PREMIUM STRENGTH / 3
POINT MOUNTING IS NECESSARY.
COMPLETE SECTION B.
2.
LOOSELY ATTACH C-HDM-404 USING HARDWARE
3.
PROVIDED.
THE MAJORITY OF HAVIS BASES HAVE AN EXTRA PEM
4.
IN ORDER TO ATTACH TO THE SUPPORT ARM. IF NOT
FIND ANOTHER LOCATION OR DRILL AND THROUGH
BOLT THE TAB BRACKET.
EXTEND THE SUPPORT ARM AND ATTACH WITH
5.
SUPPLIED HARDWARE.
TIGHTEN ALL HARDWARE.
6.
D-
C-HDM-417 VERTICAL PRINTER MOUNT
COMPLETE SECTION B.
1.
LOOSELY ATTACH C-HDM-417 BRACKET USING THE
2.
HARDWARE PROVIDED.
SLIDE TWO CARRIAGE BOLTS IN THE C-PM-101 SLOTS.
3.
LOCATE THE TWO HOLES IN THE C-HDM-417
4.
BRACKET PUSH THE CARRIAGE BOLTS THROUGH THE
HOLES AND FINGER TIGHTEN THE SERRATED NUTS
PROVIDED.
SLIDE THE PRINTER TO THE RIGHT POSITION AND
5.
TIGHTEN ALL HARDWARE.
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 3 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): 4.05
TITLE:
DWG. NO.
C-HDM_INST
REV
A
3-13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES

Product specificaties

Merk: Havis
Categorie: Niet gecategoriseerd
Model: C-HDM-186
Kleur van het product: Zwart
Gewicht verpakking: 4990 g
Correct gebruik: Auto

Heb je hulp nodig?

Als je hulp nodig hebt met Havis C-HDM-186 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Havis

Havis

Havis CST00139A Handleiding

11 Juli 2024
Havis

Havis ASS10121 Handleiding

11 Juli 2024
Havis

Havis CST00189 Handleiding

11 Juli 2024
Havis

Havis 367-5686 Handleiding

11 Juli 2024
Havis

Havis ASS60121A Handleiding

11 Juli 2024
Havis

Havis CST00159 Handleiding

11 Juli 2024
Havis

Havis 367-4873 Handleiding

11 Juli 2024
Havis

Havis CST00177 Handleiding

27 Mei 2024
Havis

Havis C-MAP-SL Handleiding

27 Mei 2024
Havis

Havis DS-GTC-211 Handleiding

27 Mei 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024
Profoto

Profoto RFi Softbox Octa Handleiding

24 December 2024
Koenic

Koenic KAP 2523 Handleiding

24 December 2024
Philips

Philips HD9921 Handleiding

24 December 2024
Philips

Philips Senseo HD7008 Handleiding

24 December 2024
Onkyo

Onkyo IRK1804C Handleiding

24 December 2024