Havis C-HDM-175 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Havis C-HDM-175 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
1/4-20 3/4" LG HHCS
1/4" LOCK WASHER
1/4" FLAT WASHER
(NOT USED FOR
POWER SEAT APPLICATIONS)
2X
1/4-20X 1" HHCS
1/4" LOCK WASHER
1/4" FLAT WASHER
MAIN BASE
ADJUSTABLE
SUPPORT FOOT
2X
5/16-18X 1" HHCS
5/16"SPLIT LOCK WASHER
5/16" FLAT WASHER
1/4-20X 1" HHCS
1/4" LOCK WASHER
1/4" FLAT WASHER
4X
5/16-18X 3/4" HHCS
5/16" LOCK WASHER
5/16" FLAT WASHER
TABS
BASE OFFSET
Installation Instructions
ATTACH SUPPORT FOOT TO MAIN BASE USING (2X) 1/4-20 X 1"
1.
HEX HEAD CAP SCREWS, LOCK WASHERS AND FLAT WASHERS.
ADJUST SUPPORT FOOT TO ITS HIGHEST POSITION, AND LIGHTLY
2.
SECURE IT.
INSTALL (2X) 5/16-18 X 1" HHCS, LOCK WASHERS AND FLAT
3.
WASHERS INTO THE THREADED HOLES ON THE MAIN BASE PLATE.
DO NOT TIGHTEN.
REMOVE TRIM AROUND PASSENGER SEAT.
4.
REMOVE PASSENGER SIDE REAR SEAT BOLTS.
5.
MANEUVER FRONT SEAT HOOKS OUT OF CORRESPONDING
6.
RECTANGULAR FLOOR HOLES.
POSITION MAIN BASE INTO THE VEHICLE, LARGE RECTANGULAR
7.
HOLES SHOULD LINE UP WITH SEAT HOOK HOLES.
PUT THE PASSENGER SIDE SEAT BACK INTO PLACE POSITIONING
8.
THE FRONT SEAT HOOKS FIRST. IT MAY BE NECESSARY TO
POSITION THE PLATE AS FAR TO THE REAR AS POSSIBLE TO ALLOW
THE SEAT TO BE EASILY TILTED FOR INSTALLATION.
REPLACE REAR SEAT BOLTS AND FINGER TIGHTEN.
9.
IF THE BASE WAS SHIFTED TO THE REAR TO INSTALL THE SEAT,
10.
PULL IT AS FAR FORWARD AS POSSIBLE.
IN NON-POWER SEAT APPLICATIONS, THE SINGLE THREADED HOLE
11.
ON THE OUTBOARD EDGE OF THE PLATE SHOULD LINE UP WITH A
HOLE IN THE SEAT RAIL.
IF APPLICABLE, INSTALL THE 1/4-20 X 1/2" HHCS, LOCK WASHER
12.
AND FLAT WASHER THROUGH THE SEAT RAIL INTO THE THREADED
HOLE AND TIGHTEN.
SLIDE THREE TABS INTO THE DRIVERS SIDE SEAT RAIL AND SECURE
13.
WITH 1/4-20 X 1" HHCS, LOCK WASHER AND FLAT WASHER.
ATTACH BASE OFFSET ASSEMBLY TO BASE USING (4X) 5/16-18
14.
3/4" HHCS, (4X) 5/16 SPLIT LOCK WASHER AND (4X) 5/16" FLAT
WASHER.
TIGHTEN 2X 5/16-18 X 1" BOLTS TO EXTEND SUPPORT FOOT TO
15.
THE FLOORING UNTIL EITHER THE BOLTS ARE FULLY TIGHTENED
OR SUFFICIENT SUPPORT FOR THE BASE HAS BEEN REACHED.
TIGHTEN 1/4-20 X 1" BOLTS, 1/4" SPLIT LOCK WASHERS & 1/4"
16.
FLAT WASHERS TO SECURE SUPPORT FOOT
C-HDM-175
INSTALLATION INSTRUCTIONS
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 1 OF 1
DO NOT SCALE DRAWING
WEIGHT (LB): 12.63
TITLE:
DWG. NO.
C-HDM-175_INST
REV
A
A
HAVIS, INC.
INSTALLATION, HDM BASE, 2014
CAPRICE


Product specificaties

Merk: Havis
Categorie: Niet gecategoriseerd
Model: C-HDM-175
Kleur van het product: Zwart
Gewicht verpakking: 5443 g
Correct gebruik: Auto

Heb je hulp nodig?

Als je hulp nodig hebt met Havis C-HDM-175 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Havis

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd