Hager TYA606D Handleiding

Hager Niet gecategoriseerd TYA606D

Lees hieronder de 📖 handleiding in het Nederlandse voor Hager TYA606D (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

6LE002682B

Output 16A / shutter/blind

Output 16A C-Load adapted /

shutter/blind

Output 16A C-Load adapted /

shutter/blind

Bn,.:

6LE002682B1 6LE002682B2 3 Hager 6LE002682B - 09/2020Hager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com

Safety instructions z

Electrical equipment may only be installed and

assembled by a qualiﬁed electrician in accor-

dance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these installation

instructions may result in damage to the

device, ﬁre or other hazards.

Hazard due to electric shock. Disconnect

before working on the device or load. Take into

account all circuit breakers that supply

dangerous voltages to the device or load.

Hazard due to electric shock. The device is not

suited for safe disconnection of the mains

supply.

Hazard due to electric shock on the SELV/PELV

installation. Not suitable for switching SELV/

PELV voltages.

Do connect only one motor per output. When

connecting several motors, motors or device

may be destroyed

Use drives with mechanical or electrical ﬁnal

position switches only. Check ﬁnal position

switches for correct adjustment. Observe

motor manufacturer's data. The device could

get damaged.

Do not connect any three-phase motors. The

device could get damaged.

Observe the motor manufacturer's data regar-

ding change-over time and max. switch-on ti-

me.

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

30V DC

auto

C8C8

C7C7

9 11

C5 C6

10 12 14 16

C5 C6 C7 C8

3 5

C2 C3

4 6 8

C2 C3 C4

C2C2

C1C1

C4C4

C3C3

1N L

(1)

(2)

(3)

(4) (5)

(6)

(7)

(8)

Fig. 1: Example device variant 8/4gang

(1) Slide switch auto/

(2) KNX bus connection terminal

(3) Connections loads

(4) Labelling ﬁeld

(5) Illuminated programming button

(6) Operation button for manual operation per

output with status LED

(7) Connections for switching voltage

(8) Mains power supply connections (only 8gang)

With variants 4/2gang, 6/3gang and 10/5gang

the basic design corresponds to the 8/4gang

device variant.

Function

System information

This device is a product of KNX system and

corresponds to the KNX guidelines. Detailed

specialised knowledge obtained from KNX training

courses is required for comprehension. The

planning, installation and commissioning of the

device is carried out with the help of KNX-certiﬁed

software.

Systemlink start-up:

The function of the device is software-dependent.

The software is to be taken from the product

database. You can ﬁnd the latest version of the

product database, technical descriptions as well

as conversion and additional support programmes

on our website.

Easylink start-up:

The function of the device is conﬁguration-depen-

dent. The conﬁguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conﬁguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Preconﬁgured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The device receives telegrams from sensors or

other controllers via the KNX installation bus and

switches electrical loads with its independent relay

contacts.

The C load variants are particularly suitable for

capacitive loads and are designed for high switch-

on currents.

Correct use

- Switch electrical loads of 230 V AC with poten-

tial-free contacts.

- Switching electrically operated motors of 230 V

AC for blinds, shutters, awnings and similar

hangings.

- Mounting on DIN rail according to DIN EN

60715 in the distribution box.

Product characteristics

- manual activation of the outputs on the device

possible, building site operation

- Status display of the outputs on the device

- Scene function

- Forced position by higher-level controller

- Connection of various external conductors

possible.

Functions in switch operation

- Time switching functions

Functions in shutter/blind operation:

- Position can be started directly

- Slat position directly controllable

- Feedback of operating state, shutter position

and slat adjustment

- 3 Alarms

Operation

Manual operation switch on/o

With the 8/4gang variants, control of the out-

puts is possible even without bus voltage when

mains voltage is connected e.g. for operation at

building sites.

Bus or mains power supply is present.

zPush switch (1) to position .

Manual operation is switched on, the outputs

can be controlled using the operation buttons

(6) independently of each other.

During manual operation, the controller is deac-

tivated via the KNX bus.

Systemlink start-up

Depending on the programming, the manual

operation is either activated permanently or

for a time period conﬁgured via the application

software. If the manual operation is blocked via

the application software, no activation takes

place.

Or:

zMove switch (1) to position .auto

The manual operation is switched o. Opera-

tion takes place solely via the KNX bus. The

output adopts the position predeﬁned by the

bus controller.

Operating outputs in manual operation

Operation takes place per output by brief repeated

presses on the operation button (table 1).

CAUTION!

Risk of destruction due to simultane-

ous pressing of the buttons for UP and

DOWN if a motor is connected when

the motor is in unprogrammed state!

Motors, hangings and the device may

be destroyed!

Always only press one button in

manual operation for unprogrammed

devices.

Status Behaviour when

button pressed brieﬂy

Switching operation

Load is switched

o. Status LED of

the button (6) is o

Switch ON the connected

load. Status LED of the

button (6) lights up.

Load is switched

on, status LED

of the button (6)

lights up

Switch OFF the connected

load. LED goes out.

Roller shutter/blind operation

Output is in stand-

by, status LED of

the button (6) is o

Movement operation starts.

Status LED of the button (6)

lights up.1)

If the roller shutter/blind

is in the ﬁnal position,

press the opposite

button to move the roller

shutter/ blind

Output active,

status LED of the

button (6) lights

up. 1)

Movement operation stops,

LED goes out.

1) LED lights up red with TYA6.. devices. LED lights up

red while moving up and green while moving down

with TXA6.. devices

Table 1: Manual operation

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

CAUTION!

Impermissible heating if the load of

the device is too high!

The device and the connected cables

may get damaged in the connection

area!

Do not exceed the maximum current

carrying capacity!

CAUTION!

Risk of destruction if parallel connec-

tion of several motors on one output!

Final position switches could fuse

together. Motors, hangings and the

device may be destroyed!

Do connect only one motor per

output!

Installing the appliance

Observe temperature range. Provide sucient

cooling.

zMount device onto DIN rail in accordance with

DIN EN 60715.

Connect device

30V DC

auto

C8C8

C7C7

9 11

C5 C6

10 12 14 16

C5 C6 C7 C8

3 5

C2 C3

4 6 8

C2 C3 C4

C2C2

C1C1

C4C4

C3C3

1N L

Fig 2: Device connection

Fig 3: Installation/deinstallation with plug-in

terminals

zConnect bus cable via connecting terminal (2).

Mains voltage can be connected optionally for

device variants 8/4gang (8). Reduction of the

power supply load is possible (see Technical

data).

Connecting loads to be switched

The output is conﬁgured as switching output.

zConnect switching voltage on the upper termi-

nal strip (7) of the device

zConnect load on the lower terminal strip (3) of

the device

Connecting blind drives

The two adjacent relay outputs / , / , C1 C2 C3 C4

C5 C6 C7 C8/ , / each form one blind output for

blind operations. Each left relay output , , C1 C3

C5 C7, is intended for the direction UP, each right

relay output , , , is intended for the C2 C4 C6 C8

direction DOWN. In manual operation, the blind is

moved UP and DOWN using the corresponding

operation buttons.

Two outputs are conﬁgured as blind output.

zConnect supply voltage of the drives on the

upper terminal strip (7). While doing so, use the

same phase (external conductors).

zConnect drives on the lower terminal strip (3).

Start-up

Systemlik: Loading the physical address and

application software

The switch (1) is in position .auto

zSwitch on bus voltage.

zPress programming button (5).

The button lights up.

If the button does not light up, no bus voltage

is present.

zLoad the physical address into the device.

Status LED of the button goes out.

zLoad application software.

zNote down the physical address on the label-

ling ﬁeld (4).

Easylink:

Information on the system conﬁguration can be

taken from the extensive description of the service

module easylink.

Start up the device.

zSwitch on mains voltage on the outputs.

zSwitch on mains supply (variant 8gang).

Determine operation time and slat adjusting

time

In blind/roller shutter operation, the operation time

for positioning the sunshade is important. The

position is calculated based on the operation time.

The slat adjusting time for slat blinds, determined

by the design, is part of the total operation time.

The opening angle of the slats is therefore set

as operation time between opened and closed

position.

The operation time for UP is normally longer

than the operation time for DOWN and must be

measured separately if necessary

zMeasure UP and DOWN operation time of the

hanging.

zMeasure slat adjusting time between OPEN

and CLOSED.

zEnter measured values into the parameter set-

ting – ... or .running time slat step time

Functional test

The functionality of the outputs is displayed via the

status LED of the operation button (6).

Appendix

Technical data

Supply voltage KNX 21-32V sTBTS

Breaking capacity µ16A AC1 230V~

Incandescent lamps 2300 W

HV halogen lamps 2300 W

Conventional transformers 1600 W

Electronic transformers 1200 W

Fluorescent lamps:

- without ballast 1200 W

- with electronic ballast (mono/duo) 20 x 36 W

Energy-saving lamps 18 x 23 W

Switching current at cos Φ = 0.6 max. 6 A

Upstream protection: circuit breaker 16 A

Minimum switching current 100 mA

Interlock time for

changing direction of travel software-dependent

Operating altitude max. 2000 m

Degree of contamination 2

Surge voltage 4 kV

Degree of protection of housing IP 20

Degree of protection of housing

under front panel IP30

Impact protection IK 04

Overvoltage class III

Operating temperature -5° ... +45°C

Storage/transport temperature -20 … +70°C

Maximum switching

cycle rate at full load 6 switching cycle/minute

Connection capacity 0.75 mm²…2.5 mm²

Communication media KNX TP 1

Conﬁguration mode S-Mode, Easy link

controller (TXA ... only)

Only C load variants

Fluorescent lamps with

conv. ballast,

parallel connection 1500 W, 200 µF

Variants 4/2gang

Energy dissipation 8 W

Maximum current permitted per device max. 40 A

Own consumption on the KNX bus:

- typical 4 mA (TYA..)

5 mA (TXA..)

- in standby 3,3 mA (TYA..)

3 mA (TXA..)

Dimension 4 TE, 4 x 17.5 mm

Variants 6/3gang

Energy dissipation 12 W

Maximum current permitted per device max. 60 A

Own consumption on the KNX bus:

- typical 4,3 mA (TYA..)

5 mA (TXA..)

- in standby 3,3 mA (TYA..)

3 mA (TXA..)

Dimension 4 TE, 4 x 17.5 mm

Variants 8/4gang

Auxiliary voltage 230V~ +10/-15%

240V~ +/-6%

Maximum current permitted per device max. 80 A

Energy dissipation 12 W

Own consumption on the KNX bus:

- typical 15,2 (TYA..)

6 mA (TXA..)

- in standby 8,6 mA (TYA..)

4 mA (TXA..)

Own consumption on the KNX bus with mains

connection:

- typical 2 mA (TXA.., TYA..)

- in standby 2 mA (TXA.., TYA..)

Dimension 6 TE, 6 x 17.5 mm

Variants 10/5gang

Energy dissipation 15 W

Maximum current permitted per device max. 100 A

Own consumption on the KNX bus:

- typical 15,9 mA (TYA..)

6 mA (TXA..)

- in standby 7,5 mA (TYA..)

4 mA (TXA..)

Dimension 6 TE, 6 x 17.5 mm

Troubleshooting

Manual operation not possible

Cause 1: Switch (1) not moved to .

Move switch to .

Cause 2: Manual operation is not enabled (Sys-

temlink).

Enable manual operation via application soft-

ware.

Bus operation is not possible

Cause 1: Bus voltage is not present.

Check bus connection terminals for correct

polarity.

Check bus voltage by brieﬂy pressing the pro-

gramming button (5), red LED lights up if bus

voltage is present.

8gang: If mains voltage without bus voltage is

present - red LED of programming button (5)

ﬂashes.

Cause 2 : Manual operation is active. Switch (1) is

in position .

Move switch (1) to position .auto

Shutters/blinds do not move to the ﬁnal

position

Cause: Operation time for the shutters/blinds set

incorrectly.

Check operation times. Measure again and

reprogram if necessary.

Σ max

20 A

Σ max

20 A

Σ max

20 A

C1 C2 C3 ...

Cn ...

Overall load current rating

of neighbouring outputs

20 A

WARNING!

The supply voltages of the electric

circuits connected to the product

must always all fall within the same

voltage range (LV (low voltage), VLV

(very-low voltage) or SELV (safety

extra-low voltage)).

Connecting voltages of dierent

ranges is strictly prohibited.

Correct Disposal of This product

(Waste Electrical & Electronic

Equipment).

(Applicable in the European Union and other European

countries with separate collection systems).

This marking shown on the product or its literature

indicates that it hould not be disposed with other

household wasted at the end of its working life. To prevent

possible harm to the environment or human health from

uncontrolled waste disposal, please separate this from

other types of wastes and recycle it responsibly to

promote the sustainable reuse of material resources.

Household users should contact either the retailer where

they purchased this product, or their local government

oce, for details of where and how they can take this item

for environmentally safe recycling.

Business users should contact their supplier and check

the terms and conditions of the purchase contract. This

product should not be mixed with other commercial

wastes of disposal.

Usable in all Europe

and in Switzerland

Product specificaties

Merk:	Hager
Categorie:	Niet gecategoriseerd
Model:	TYA606D
Kleur van het product:	Grijs
Diepte:	65 mm
Hoogte:	90 mm
Internationale veiligheidscode (IP):	IP20
Bedrijfstemperatuur (T-T):	-5 - 45 °C
Aantal producten inbegrepen:	1 stuk(s)