Hager TXA624D Handleiding

Hager Niet gecategoriseerd TXA624D

Lees hieronder de 📖 handleiding in het Nederlandse voor Hager TXA624D (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

6LE002722A

TYA624B

Output 4gang shutter 24 V

TYA624D

Output 4gang shutter/blind

24 V

TXA624D

Output 4gang shutter/blind

24 V

6LE002722A1

Safety instructions

Electrical equipment may only be installed and

assembled by a qualied electrician in accor-

dance with the relevant installation standards,

guidelines, regulations, directives, safety and

accident prevention regulations of the country.

Failure to comply with these installation in-

structions may result in damage to the device,

re or other hazards.

Hazard due to electric shock. Disconnect be-

fore working on the device or load. Take into

account all circuit breakers that supply dan-

gerous voltages to the device or load.

Connect one motor per output only. If several

motors are connected, motors or device might

be destroyed.

Use drives with mechanical or electrical nal

position switches only. Check nal position

switches for correct adjustment. Observe mo-

tor manufacturer's data. The device can be da-

maged.

Risk of injury. Use the device to control blind

and shutter drives or awnings only. Do not

switch any other loads.

Observe the motor manufacturer's data regar-

ding change-over time and max. switch-on time

(ED).

These instructions are an integral component

of the product and must be retained by the end

user.

Design and layout of the device

C4C4

C3C3

30V DC

3 5

7 9

4 6 8 10

C1 C3

C2 C4

auto

(1)

(2) (3)

(4) (5)

(6)

(3)

Figure 1: device overview

(1) Slide switch /auto

(2) KNX bus connection terminal

(3) Connections of loads

(4) Labelling eld with cover

(5) Illuminated programming button

(6) Operation button for manual operation per

output with status LED

Function

System information

This device is a product of KNX system and corre-

sponds to the KNX guidelines. Detailed specialised

knowledge obtained from KNX training courses is

required for comprehension. The planning, installa-

tion and commissioning of the device is carried out

with the help of KNX-certied software.

Systemlink commissioning

The function of the device is software-dependent.

The software is to be taken from the product

database. You can nd the latest version of the

product database, technical descriptions as well as

conversion and additional support programmes on

our website.

Easylink commissioning

The function of the device is conguration-depen-

dent. The conguration can also be done using

devices developed specially for simple setting and

start-up.

This type of conguration is only possible with

devices of the easylink system. Easylink stands for

easy, visually supported start-up. Precongured

standard functions are assigned to the in/outputs

by means of a service module.

Functional description

The devices are used to control motor-operated

building ttings such as shutters and blinds via the

KNX bus. The devices have 4 outputs from which

each output can be activated independently.

Correct use

- Switching of electrically driven 24 V motors for

blinds, shutters, awnings and similar hangings.

- Mounting on DIN rail according to

DIN EN 60715 in the distribution box.

Product characteristics

- independent outputs, activation via KNX bus.

- Status display of the outputs on the device.

- manual activation of the outputs on the device

possible, building site operation.

- Position can be started directly.

- 3 Alarms.

- Scene function.

- Forced position by higher-level controller.

Blind actuators only

- Slat position directly controllable.

Operation

Manual operation switch on/off

Bus voltage supply is present.

zPush switch (1) to position .

Manual operation is switched on, the outputs

can be controlled using the operation buttons

(6) independently of each other.

During manual operation, the controller is deac-

tivated via the KNX bus.

Systemlink commissioning: depending on the

programming, the manual operation is activated

permanently or for a time period congured via

the application software.

If the manual operation is blocked via the appli-

cation software, no activation takes place.

zMove switch (1) to position .auto

The manual operation is switched off. Opera-

tion takes place solely via the KNX bus. The

output takes the position predened by the bus

controller.

Operating outputs in manual operation

Operation takes place per output by brief repeated

presses on the operation button (6) (table 1).

Status Behaviour when

briey pressing the

button

Manual operation is

switched on, initial

operation of an output.

Move DOWN, re-

gardless of output

status.

Movement operation

active, status LED of the

button (6) lights up.

Movement operation

stops.

Output is in standby,

status LED of the button

(6) is off.

Movement operation

in opposite direction of

the last movement.

Table 1: manual operation

Information for electricians

Installation and electrical connection

DANGER!

Touching live parts can result in an

electric shock!

An electric shock can be lethal!

Disconnect the connecting cables

before working on the device and

cover all live parts in the area!

CAUTION!

Risk of destruction if parallel connec-

tion of several motors on one output!

Final position switches could fuse

together. Motors, hangings and the

device may be destroyed!

Only connect one motor per

output!

Bn,.:

Installing the appliance

Observe temperature range. Provide sufcient

cooling.

zMount device onto DIN rail in accordance with

DIN EN 60715.

Connect device

C4C4

C3C3

30V DC

3 5

7 9

4 6 8 10

C1 C3

C2 C4

24 V DC max.

auto

24 V max.s

Fig 2: device connection

Fig 3: installation/deinstallation

with plug-in terminals

Connect bus cable via connecting terminal (2).

zConnect bus voltage.

zConnect motors.

Start-up

Systemlink: loading physical address and

application software

The switch for manual operation (1) is in position

auto.

zSwitch on bus voltage.

zPress programming button (5).

The button lights up.

If the button does not light up, no bus voltage

is present.

zLoad the physical address into the device.

Status LED of the button goes out.

zLoad application software.

zNote down the physical address on the labelling

eld (4).

Easylink

Information on the system conguration can be

taken from the extensive description of the service

module easylink.

Starting up the device

zSwitch the operating voltage on.

Determine operation time and slat adjusting

time

In blind/roller shutter operation, the operation time

for positioning the sunshade is important. The posi-

tion is calculated based on the operation time. The

slat adjusting time for slat blinds, determined by

the design, is part of the total operation time. The

opening angle of the slats is therefore set as ope-

ration time between opened and closed position.

The operation time for UP is normally longer

than the operation time for DOWN and must be

measured separately if necessary.

zMeasure UP and DOWN operation time of the

hanging.

zMeasure slat adjusting time between OPEN

and CLOSED.

zEnter measured values into the parameter

setting – ... or .running time slat step time

Functional test

The functionality of the outputs is displayed via the

status LED of the operation button (6).

Appendix

Technical data

Supply voltage KNX 21-32V SELVs

Own consumption on the KNX bus:

- typical 5,2 mA (TYA..)

5 mA (TXA..)

- in standby 4,5 mA (TYA..)

3 mA (TXA..)

Breaking capacity µ 6A DC1 24V s

Energy dissipation 2 W

Switching current smax. 6 A

Operating altitude max. 2000 m

Degree of contamination 2

Surge voltage 4 kV

Degree of protection of housing IP20

Degree of protection of housing

under front panel IP30

Impact protection IK 04

Overvoltage class III

Operating temperature -5°C…+45°C

Storage/transport temperature -20°C … +70°C

Maximum switching cycle rate

at full load 20 switching cycle/minute

Connection capacity 0.75 mm²…2.5 mm²

Dimension 4 TE, 4 x 17.5 mm

Communication media KNX TP 1

Conguration mode S-Mode, easy link

controller (TXA624D)

Troubleshooting

Manual operation not possible

Cause 1: switch (1) not moved to .

Move switch to .

Cause 2: manual operation has not been enabled

(Systemlink).

Enable manual operation via application soft-

ware.

Bus operation is not possible

Cause 1: bus voltage is not present.

Check bus connection terminal for correct

polarity.

Check bus voltage by briey pressing the pro-

gramming button (5), red LED lights up if bus

voltage is present.

Cause 2: manual operation is active. Switch (1) is

in position .

Move switch (1) to position .auto

Shutters/blinds do not move to the nal

position

Cause: Operation time for the shutters/blinds set

incorrectly.

Check operation times. Measure again and

reprogram if necessary.

Correct Disposal of This product

(Waste Electrical & Electronic

Equipment).

(Applicable in the European Union and other European

countries with separate collection systems).

This marking shown on the product or its literature

indicates that it hould not be disposed with other

household wasted at the end of its working life. To prevent

possible harm to the environment or human health from

uncontrolled waste disposal, please separate this from

other types of wastes and recycle it responsibly to

promote the sustainable reuse of material resources.

Household users should contact either the retailer where

they purchased this product, or their local government

oce, for details of where and how they can take this item

for environmentally safe recycling.

Business users should contact their supplier and check

the terms and conditions of the purchase contract. This

product should not be mixed with other commercial

wastes of disposal.

Usable in all Europe

and in Switzerland

2 Hager 12.16 - 6LE002722AHager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com

Product specificaties

Merk:	Hager
Categorie:	Niet gecategoriseerd
Model:	TXA624D
Kleur van het product:	Grijs
Hoogte:	90 mm
Internationale veiligheidscode (IP):	IP20
Bedrijfstemperatuur (T-T):	-5 - 45 °C
Aantal producten inbegrepen:	1 stuk(s)