GW Instek PEL-3032E Handleiding

GW Instek Meetapparatuur PEL-3032E

Lees hieronder de 📖 handleiding in het Nederlandse voor GW Instek PEL-3032E (2 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

QUICK START GUIDE

GW INSTEK PAR NO. 82EL T -3KE00M 1

This section contains the basic safety symbols that may

appear on the accompanying User Manual CD or on the

instrument. For detailed safety instructions and

precautions, please see the Safety Instructions chapter

in the user manual CD.

These safety symbols may appear in the user manual or

on the instrument.

Warning: Identifies conditions or

practices that could result in injury or

loss of life.

Caution: Identifies conditions or

practices that could result in damage

to the instrument or to other

properties.

DANGER High Voltage

Attention Refer to the Manual

Earth (ground) Terminal

Frame or Chassis Terminal

Do not dispose electronic equipment

as unsorted municipal waste. Please

use a separate collection facility or

contact the supplier from which this

instrument was purchased.

When using the instrument in the United Kingdom,

make sure the power cord meets the following safety

instructions.

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed as

follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

loured Green/Green & Yellow. or co

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal

marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or

contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable of

0.75mm2

should be protected by a 3A or 5A fuse. Larger conductors

would normally require 13A types, depending on the connection

method used.

Any exposed wiring from a cable, plug or connection that is engaged

in a live socket is extremely hazardous. If a cable or plug is deemed

hazardous, turn off the mains power and remove the cable, any

fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

The Getting Started chapter introduces the instrument’s

main features, appearance, and set up procedure.

The PEL-3000E is an economic, standalone, high

performance DC electronic load positioned to test a

wide range of different power sources. The DC

electronic load is fully programmable to simulate

anything from basic static loads to complex dynamic

loads. The PEL-3000E is extremely robust and capable

of molding to any test environment.

PEL 3031E-

1V-150V

6A (Low range)

60A (High range)

300W

PEL 303- 2E

2.5V-500V

1.5A (Low range)

15A (High range)

300W

•High slew rates of up to 2.5A/μs

for a fast response speed -(PEL

3031E)

•High resolution – 16 bit

•7 operating modes: CC, CV, CR,

CP, CC+CV, CR+CV, CP+CV

•Fully programmable with normal

and fast sequences

•Soft start

•Dynamic mode

•OCP, OVP and other protection

features

•Remote sense

•Integrated meter

•Rack-mountable

•USB and GPIB

•External voltage or resistance

control

•Rear panel trigger in/out BNC

•Analog external control

Mode

I Range

H 60A

V Range

L 15V

Function

Static Configure

0.0000V

0.000A

0.00w

SlewRate 2500

CC B Value 0.000

CC A Value 0.000

LOADUSB

A Value

Fine

mA/us

1. Main frame status

panel

2. Operation status

panel

3. Soft keys

4. Setting area

5. Measurement area

Use the following when first using the procedures

PEL- E to power up the instrument, restore the 3000

factory default settings and check the firmware

version. Lastly, the Conventions section will introduce

you to the basic operating conventions used

throughout the user manual.















 



 















  

1. J1 Frame control

ports

2. TRIG OUT BNC

3. TRIG IN BNC

4. Exh aust fan

5. Power socket and

switch

6. GPIB (optional)

7. USB device port



















































 





 









 

 







P E L - 3 0 3 1 E





  

1. Air inlet

2. LCD Display

3. Function keys

4. Power key

5. Main/Local key

6. FUNC/File key

7. Help/Utility key

8. Short key

9. Load On/Off

10. Scroll wheel

11. Number pad,

Clear/Lock and Enter

keys

12. USB port, Preset and

Shift keys

13. Sense-, Sense+

terminals

14. Input terminals

User /Programming Manual CD

Quick Start Guide (this document)

Power C ord x1

Region Dependent

Front terminal washers ( M6) x2

61SF-062104N1

Remote sense cables, red x1, black

GTL- 105A

GPIB cable, 2.0m

GTL- 248

USB ca , Type A - ble Type B

GTL- 246

Dust filter

PEL 010-

GPIB option

PEL 004-

This manual contains proprietary information, which is

protected by copyright. All rights are reserved. No part

of this manual may be photocopied, reproduced or

translated to another language without prior written

consent of Good Will Corporation.

The information in this manual was correct at the time

of printing. However, Good Will continues to improve

its products and therefore reserves the right to change

the specifications, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd. No. 7-1, Jhongsing Rd., Tucheng

Dist. New i ., Taipei C ty 236, Taiwan

1. Insert the AC power cord into the power socket.

2. Turn the power switch on

from the rear panel.

(O → ) —

3. If the unit doesn’t turn on, press the ON/STBY

key on the front panel.

 The ON/STBY key will go from standby

(red) to green) ON ( .

4. The unit will show the splash screen and then

load the settings from when the unit was last

powered down.

When first using the - E, recall the factory PEL 3000

default settings to ensure the unit is in a known state.

See the user manual for a list of the default settings.

1. Press

Shift

File

FUNC

2. Select Media/Default [F1].

3. Select Factory Default [F2].

4. Press Factory Default [F2] again to confirm.

The PEL- E allows the firmware to be updated by 3000

end-users. Before using the - E, please check PEL 3000

the GW Instek website or ask your local distributor for

the latest firmware. Before updating the firmware,

please check the firmware version.

View Firmware Version

1. Press

Shift

Utility

Help

2. Select System/Info[F1].

3. The system information is listed in the display.

 Model: - XE PEL 303

 Serial Number: XXXXXXXX

 Firmware Ve r.: 1.XX

 GW Instek website address.

Firmware update

1. Press

Shift

File

FUNC

2. Select with the - USB Media [F1] soft key.

3. Press the File Utility [F5] - soft key.

4. Select the *.UPG upgrade file and press Select[F1]

twice. Once to select the file and once to confirm.

5. Wait for the update to complete and reset the

power.

Do not turn the load generator off or

remove the USB memory when the

firmware is being read or upgraded.

The following conventions are used throughout the

user manual. Read the conventions below for a basic

grasp of how to operate the - E menu system PEL 3000

using the front panel keys.

Soft-menu keys

The F1 to F5 function keys at the bottom of the

display correspond directly to the -menu keys soft

on top.

CAL.

Lock

Utility

EnterClear

Shift

Preset

Load

On/

Off

Help

FUNC

Short

A / B

Mode

I Range

H 60A

V Range

L 15V

Function

Static Configure

SlewRate 2500

CC B Value 0.000

CC A Value 0.000

A Value

Fine

mA/us

Select Sub Menu

Configure

Pressing this type of soft-menu key will enter a

submenu.

Toggle Parameter or State

Mode

This type of soft-menu icon has the function/item

on the top of the label and the selected setting or

mode on the bottom of the label.

Repeatedly press the associated function key (F1-

F5) to cycle through each setting.

For some parameters, a popup window will also

appear. Selection of the setting is the same.

Repeatedly pressing the relevant function key (F1-

F5) will cycle through each setting.

Parameter Input

The scroll wheel, Enter key and number pad can

be used to edit parameter values.

1. Use the scroll wheel to move the cursor to the

desired parameter.

 A scroll bar is shown when there are

additional parameters off-screen.

Mode

I Range

H 60A

V Range

L 15V

Response

Fast Configure

0.0000

0.000

0.00

+CV OFF

CP B Value 0.00

CP A Value 0.00

LOADUSB

Fine

A Value

2. Press the

Enter

key to select the

parameter.

3. Then use the number pad* or scroll wheel**

to edit the parameter v alue.

Mode

I Range

H 60A

V Range

L 15V

Response

Fast Configure

0.0000

0.000

0.00

+CV OFF

CP B Value 0.00

CP A Value

LOADUSB

Fine

A Value

0.00

Clearing a Value*

*When editing a parameter with the number pad,

pressing the

Clear

key will restore the

parameter to the previous value.

Coarse/Fine Adjustment **

**When a parameter is highlighted (step 3 above)

pressing the scroll wheel will toggle the scroll

wheel resolution between fine and coarse.

Mode

I Range

H 60A

V Range

L 15V

Response

Fast Configure

0.0000

0.000

0.00

+CV OFF

CP B Value 0.00

CP A Value

LOADUSB

Fine

A Value

0.00

Note: There is a second method of fine adjustment

that allows you to edit parameters one digit value

at a time using the scroll wheel. This is called

Cursor mode. Please see the user manual for more

information.

Ω Ω

Ω Ω

Ω Ω

Ω Ω

Ω Ω

Ω Ω

Ω

The following are the basic specifications for the -PEL

3000E. For detailed specifications, please see the user

manual.

Ω

Ω Ω

Ω Ω

Entering Alphanumeric Characters

When renaming files, creating memos or notes,

you will be required to enter alphanumeric

characters when the character entry screen

appears.

 Only alphanumeric characters as well as

space [ ], underscore [_] and minus [-]

characters allowed. are

1. Use the scroll wheel to move the cursor to the

desired character.

A B C D E F G H I J K L M

N O P Q R S T U V W X Y Z

1 2 3 4 5 6 7 8 9 0 _ 1

Rename:

Filename

2. Press the

Enter

key or Enter Character[F1]

to select a character.

3. To delete a character, press Back Space[F2].

4. To save the file name or memo, press

Save[F3].

GOOD WILL INSTRUMENT CO., LTD.

declare that the below mentioned product

Type of Product: Programmable Electronic Load

Model Number: PEL-3000E

is herewith confirmed to comply with the requirements set out in the

Council Directive on the Approximation of the Laws of the Member States

relating to Electromagnetic Compatibility (2014/30/EU) and Low Voltage

Directive (2014/35/EU ).

For the evaluation regarding the Electromagnetic Compatibility and Low

Voltage Directive, the following standards were applied:

◎ EMC

EN 61326-1

EN 61326-2-1

Electrical equipment for measurement, control and

laboratory use EMC requirements (2013) ––

Conducted & Radiated Emission

EN 55011: 2009+A1:2010 Class A

Electrical Fast Transients

EN 61000-4-4: 20 12

Current Harmonics

EN 61000-3-2: 20 14

Surge Immunity

EN 61000-4-5: 2006

Voltage Fluctuations

EN 61000-3-3: 2013

Conducted Susceptibility

EN 61000-4-6: 2014

Electrostatic Discharge

EN 61000-4-2: 2009

Power Frequency Magnetic Field

EN 61000-4-8: 2010

Radiated Immunity

EN 61000-4-3: 2006+A1:2008+A2:2010

Voltage Dip/ Interruption

EN 61000-4-11: 2004

Low Voltage Equipment Directive 2014/35/EU

Safety Requirements

EN 61010-1: 2010

EN 61010-2-030: 2010

GOOD WILL INSTRUMENT CO., LTD.

No. 7-1, Jhongsing Road, Tucheng Dist., New Taipei City 236, Taiwan

Tel: +886-2-2268-0389 Fax: +866-2-2268-0639

Web: Email:

www.gwinstek.com marketing@goodwill.com.tw

GOOD WILL INSTRUMENT (SUZHOU) CO., LTD.

No. 521, Zhujiang Road, Snd, Suzhou Jiangsu 215011, China

Tel: +86-512-6661-7177 Fax: +86-512-6661-7277

Web: Email:

www.instek.com.cn marketing@instek.com.cn

GOOD WILL INSTRUMENT EURO B.V.

De Run 5427A, 5504DG Veldhoven, The Netherlands

Tel: +31(0)40-2557790 Fax: +31(0)40-2541194

Email:

sales@gw-instek.eu

Product specificaties

Merk:	GW Instek
Categorie:	Meetapparatuur
Model:	PEL-3032E

Heb je hulp nodig?

Als je hulp nodig hebt met GW Instek PEL-3032E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Meetapparatuur GW Instek

GW Instek PEL-3032E Handleiding

14 November 2024

GW Instek GDS-2202A Handleiding

16 April 2024

GW Instek GPT-9602 Handleiding

11 Januari 2024

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

TFA 40.1001 Handleiding

21 December 2024

Ansmann Comfort Check Handleiding

20 December 2024

PCE Instruments PCE-PST 1 X Handleiding

16 December 2024

Steinberg SBS-LF-147 Handleiding

15 December 2024

Steinberg SBS-SM-135C Handleiding

15 December 2024

Steinberg SBS-MT-100 Handleiding

15 December 2024

Steinberg SBS-SM-130C Handleiding

15 December 2024

Steinberg SBS-DT-999 Handleiding

15 December 2024

Steinberg SBS-DL-123D Handleiding

15 December 2024

Steinberg SBS-LF-141 Handleiding

15 December 2024