GFP 255 C Handleiding
GFP
Lamineersysteem
255 C
Lees hieronder de 📖 handleiding in het Nederlandse voor GFP 255 C (31 pagina's) in de categorie Lamineersysteem. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/31
Gfp
255 C
July
2012
1
OPERATING MANUAL Gfp 255 C
Please read this manual carefully before operating!
Unpacking, assembly, and operating videos are available at
www.gfpsmoothstart.com
Gfp
255 C
July
2012
2
Table of Contents
Contents Page
1. Introduction …………………………………………………… 3
2. Important Safety Instructions………………………………….. 3
3. Installation Safeguards ……………………………………….. 4
4. General Safeguards……………………………………………. 5
5. Operating Conditions …………………………………………. 6
6. System Components ………………………………………….. 7
7. Control Panel …………………………………………………. 8
8. Packing List ………………………………………………… .. 9
9. Installation
A. Uncrate the machine……………………………………. 10
B. Remove machine from Skid……………………………. 11
C. Assemble machine stand……………………………….. 12
D. Set Machine on stand…………………………………... 13
E. Bolt Machine to stand………………………………….. 14
F. Attach supply support brackets………………………… 14
10. Installing upper rewind housings..…………………………….. 15
11. Additional installation items ……….…………………………. 15
12. Installing upper shaft and brakes…………. ………………….. 16
13. Loading bottom supply roll………..…………………………. 17
14. Loading top supply roll……………………………………….. 18
15. Threading film.………………………………………………... 19
16. Operation..………….. ………………………………………… 20
17. Roller gap……………………………………………………… 20
18. Laminating
A. Single sheets using a sled……………………………….. 21
B. Multiple sheets using a roll of Kraft Paper……………… 22
C. Media from a roll………………………………………… 22
19. Mounting
A. Pre-coating mounting boards…………………………… 23
B. Mounting print to pre-coated mounting board..………… 23
20. Troubleshooting ………………………………………………. 24
21. Specifications …………………………………………………. 25
22. Warranty ………………………………………………………. 26
Gfp
255 C
July
2012
3
1. Introduction
Thank you for choosing a Gfp laminator. It has been designed and manufactured to
provide years of continuous service. Please read this manual thoroughly before
operating. Please inspect the box and the laminator for shipping damage. Damage
should be brought to the attention of the delivering carrier immediately. For a list of
shipping components see “Packing List” on page 9.
2. Important Safety Instructions
In this operating manual you will find important safety messages regarding the
product.
Read these instructions carefully, failure to comply with the following safety
procedures could result in serious injury.
WAR$I$G Do not attempt to service or repair the laminator. Only
authorized maintenance and service technicians should make repairs.
WAR$I$G Do not connect the laminator to an electrical supply or attempt
to operate the laminator until you have completely read these instructions.
Maintain these instructions in a convenient location for future reference.
WAR$I$G To guard against injury, the following safety precautions must
be observed in the installation and use of the laminator
Product specificaties
Merk: | GFP |
Categorie: | Lamineersysteem |
Model: | 255 C |
Heb je hulp nodig?
Als je hulp nodig hebt met GFP 255 C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lamineersysteem GFP
14 Augustus 2023
Handleiding Lamineersysteem
- Lamineersysteem Quigg
- Lamineersysteem Brother
- Lamineersysteem DESQ
- Lamineersysteem Ednet
- Lamineersysteem Fellowes
- Lamineersysteem GBC
- Lamineersysteem Hama
- Lamineersysteem Hema
- Lamineersysteem Konig
- Lamineersysteem Leitz
- Lamineersysteem Lervia
- Lamineersysteem Marquant
- Lamineersysteem Nedis
- Lamineersysteem Powerfix
- Lamineersysteem Renkforce
- Lamineersysteem Royal Sovereign
- Lamineersysteem Sencor
- Lamineersysteem United Office
- Lamineersysteem Olympia
- Lamineersysteem Exibel
- Lamineersysteem Tracer
- Lamineersysteem Genie
- Lamineersysteem Aurora
- Lamineersysteem Q-CONNECT
- Lamineersysteem Pavo
- Lamineersysteem Peach
- Lamineersysteem Rexel
- Lamineersysteem SEAL
Nieuwste handleidingen voor Lamineersysteem
5 December 2024
5 November 2024
5 November 2024
20 Oktober 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
8 Augustus 2024
2 Juli 2024