Genelec 8030B Handleiding

Genelec Speaker 8030B

Lees hieronder de 📖 handleiding in het Nederlandse voor Genelec 8030B (32 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

8030B

Operating Manual 2-7

Betriebsanleitung 8-13

Manuel d’utilisation 14-19

Käyttöohje 20-25

Bruksanvisning 26-31

2 English

General description

The bi-amplified GENELEC 8030B is a two way

active monitoring loudspeaker designed to be small

but still have high output, low coloration, and broad

bandwidth.

The 8030B is ideal for near ﬁeld monitoring,

mobile vans, broadcast and TV control rooms, sur-

round sound systems, home studios, multimedia

applications and also for use with computer sound-

cards. As an active loudspeaker, it contains driv-

ers, power ampliﬁers, active crossover ﬁlters and

protection circuitry. The MDE™ (Minimum Diffrac-

tion Enclosure™) loudspeaker enclosure is made

of die-cast aluminium and shaped to reduce edge

diffraction. Combined with the advanced Direc-

tivity Control WaveguideTM (DCWTM), this design

provides excellent frequency balance in difﬁcult

acoustic environments. If necessary, the bass

response of the 8030B’s can be extended with a

suitable Genelec subwoofer.

Positioning the loudspeaker

Each 8030B monitor is supplied with an inte-

grated ampliﬁer unit, mains cable and an operating

manual. After unpacking, place the loudspeaker in

its required listening position, taking note of the line

of the acoustic axis. The axes of all loudspeakers

should converge at ear height at the listening position

(see Figure 1).

Connections

Before connecting up, ensure that the mains

switch is off and the volume control fully counter-

clockwise. These controls are located on the front

panel of the loudspeaker. Do not connect the loud-

speaker to an unearthed mains supply or using an

unearthed mains cable.

Audio input is via a 10 kOhm balanced female

XLR connector labelled “INPUT”. An unbalanced

source may be used as long as pin 3 is grounded

to pin 1 at the unbalanced source connector (see

Figure 2).

The male XLR “OUTPUT” connector can be

used for daisy-chaining up to six 8030B’s together

or for connecting a Genelec 7050B subwoofer. The

volume control attenuates the signal on this output,

so the ﬁrst “master” loudspeaker on a daisy-chain

can be used to adjust the level on the whole chain.

The volume controls on the “slave” loudspeakers

should be set fully clockwise.

Once the connections have been made, the

loudspeakers are ready to be switched on.

ISSTM autostart function

When the power switch on the front panel of the

loudspeaker is set to “ON”, the Intelligent Signal

SensingTM

(ISSTM) autostart function of the 8030B is

active. Automatic powering down to standby mode

happens after a certain time when playback has

ended. The power consumption in standby mode is

typically less than 0.5 watts. The playback will auto-

matically resume once an input signal is detected

from the source.

There is a slight delay in the automatic power-

ing up. If this is undesirable, the ISS

TM function can

be disabled by setting the “ISS DISABLE” switch

8030B

Active Monitoring System

English 3

on the back panel to “ON” position. In this mode,

the monitor is powered on and off using the power

switch on the front panel.

Setting the volume control

The input sensitivity of the loudspeaker can be

matched to the output of the audio signal source

by adjusting the volume control on the front panel.

Setting the tone controls

The frequency response of Genelec 8030B can

be adjusted to match the acoustic environment by

setting the tone control switches on the rear panel.

The controls are “Treble Tilt”, “Bass Tilt” and “Bass

Roll-Off”. An acoustic measuring system such as

WinMLS is recommended for analyzing the effects

of the adjustments, however, careful listening with

suitable test recordings can also lead to good

results if a test system is not available. Table 1

shows some typical settings in various situations.

Figure 4 shows the effect of the controls on the

anechoic response.

Treble Tilt

Treble Tilt (switch 2) attenuates the treble response

above 5 kHz by 2 dB, which can be used for smooth-

ening down an excessively bright sounding system.

Bass Tilt

Bass Tilt offers three attenuation levels for the bass

response below 1 kHz, usually necessary when the

loudspeakers are placed near room boundaries.

The attenuation levels are -2 dB (switch 4 “ON”), -4

dB (switch 5 “ON”) and -6 dB (both switches “ON”).

Figure 1: Location of the acoustic

axis

Figure 2: Type of cable needed if

unbalanced source is used (ex-

ample shown is RCA output to the

XLR input)

Figure 3: Control and connector layout on the rear panel of

the 8030B.

190 mm

ACOUSTIC

AXIS

> 0,7 m

REFLEX PORT

TONE CONTROLS

Iso-Pod™ TABLE

STAND

THREADS FOR

CEILING AND

WALL MOUNTS

292-8030W

COMPOSANT 'INT ÉRIEURREMPLAÇABL ARÀ L EP

OUVRIR. NE S EXPOSER 'EAU AUCUNPA À L OU L'HUMIDITÉ.

L'UTILISAT EUR.ADRESSER UTERÉPARA NTO TION À U

PERSONNELQUALIFIÉ. CETA PPAREILDOIT ÊTRE

RACCORDÉÀ LAT ERRE.

NOTSUBJECT TER MOISTURE.NO USERSERVICEABLETO WA OR

PARTS I DPNSIDE.REFER SERVICING QUALIFIETO ERSONNEL.

USE EART HED ONNECTIOMAINS C NONLY.

ELECTRIC SHOCKHAZ AR D. DONO PEN.DOT O

WARNING:

RISQUE DECHO LECTRIQUE.NE SC É PA

AVERTIS SEMENT:

LAITE ONLIITET T ÄVÄ S UOJAMAADOITUSKOSKETTIMILLAVARUS-

TET T UUNPIST ORASIAAN.APPARATET MÅ T ILKOPLES JORDET

ST IKKONT AKT APPARATENSKALLANSLUTASTILL JORDA. T UTTAG.

292-80 30T-6

MAINS INPUT

50 / 60 Hz 80 W 230 V~

SERIAL NUMB ER

8030B BI-AMPLIFIED

MONITORING SYST EM

MAGNETICAL SHIELDEDLY

MAD E IN FINLAND www.genele c.com

GND +-

OUT

1 2

+ GND-

2IN 1

ALL OFF

55 1k 5k 20k

BAS S ANDTREB LE TILT

-2

-4

-6

4+5

BAS S ROLL-OFF

ALL OFF

55 85 500 H z

TREBLE TILT-2dB

BASS ROLL-OFF -6dB 85H z

-6 3

BASS TILT-2 dB

BASS TILT-6 dB

OFF

BASS TILT-4 dB

ISS DISABLE

CONNECTOR PANEL

(HORIZONTAL)

Product specificaties

Merk:	Genelec
Categorie:	Speaker
Model:	8030B
Kleur van het product:	Zwart
Gewicht:	5600 g
Breedte:	189 mm
Diepte:	178 mm
Hoogte:	299 mm
Materiaal behuizing:	Aluminium
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	80 W
Equalizer-instellingen:	Nee
Aanbevolen gebruik:	Universeel
Impedantie:	- Ohm
Geschikt voor buitengebruik:	Nee
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Vloer
Aantal drivers:	2
Woofer:	Ja
Frequentiebereik:	50 - 25000 Hz
Gevoeligheid:	100 dB
Luidspreker soort:	2-weg
Totale harmonische vervorming (THD):	0.05 procent
Diameter woofer:	5 "
Diameter hogetonenluidspreker:	1.33 "
XLR in:	Ja
Tweeter:	Ja
Crossover frequentie:	3000 Hz