Genelec 8030A Handleiding

Genelec Speaker 8030A

Lees hieronder de 📖 handleiding in het Nederlandse voor Genelec 8030A (32 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 88 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

8030A

Operating Manual 2-7

Betriebsanleitung 8-13

Manuel d’utilisation 14-19

Käyttöohje 20-26

Bruksanvisning 25-31

2 English

General description

The bi-ampliﬁed GENELEC 8030A is a two way

active monitoring loudspeaker designed to be small

but still have high output, low coloration, and broad

bandwidth.

The 8030A is ideal for near ﬁeld monitoring,

mobile vans, broadcast and TV control rooms, sur-

round sound systems, home studios, multimedia

applications and also for use with computer sound-

cards. As an active loudspeaker, it contains driv-

ers, power ampliﬁers, active crossover ﬁlters and

protection circuitry. The MDE™ (Minimum Diffrac-

tion Enclosure™) loudspeaker enclosure is made

of die-cast aluminium and shaped to reduce edge

diffraction. Combined with the advanced Direc-

tivity Control WaveguideTM (DCWTM), this design

provides excellent frequency balance in difﬁcult

acoustic environments. If necessary, the bass

response of the 8030A’s can be extended with a

Genelec 7050B or 7060B subwoofer.

Positioning the loudspeaker

Each 8030A monitor is supplied with an integrated

ampliﬁer unit, mains cable and an operating manual.

After unpacking, place the loudspeaker in its required

listening position, taking note of the line of the acous-

tic axis. The axes of all loudspeakers should converge

at ear height at the listening position (see Figure 1).

Connections

Before connecting up, ensure that the mains

switch is off and the volume control fully counter-

clockwise. These controls are located on the front

panel of the loudspeaker. Do not connect the loud-

8030A

Active Monitoring System

English 3

speaker to an unearthed mains supply or using an

unearthed mains cable.

Audio input is via a 10 kOhm balanced female

XLR connector labelled “INPUT”. An unbalanced

source may be used as long as pin 3 is grounded

to pin 1 at the unbalanced source connector (see

Figure 2).

The male XLR “OUTPUT” connector can be

used for daisy-chaining up to six 8030A’s together

or for connecting a Genelec 7050B subwoofer. The

volume control attenuates the signal on this output,

so the ﬁrst “master” loudspeaker on a daisy-chain

can be used to adjust the level on the whole chain.

The volume controls on the “slave” loudspeakers

should be set fully clockwise.

Once the connections have been made, the

loudspeakers are ready to be switched on.

Setting the volume control

The input sensitivity of the loudspeaker can be

matched to the output of the audio signal source by

adjusting the volume control on the front panel.

Setting the tone controls

The frequency response of Genelec 8030A can

be adjusted to match the acoustic environment by

setting the tone control switches on the rear panel.

The controls are “Treble Tilt”, “Bass Tilt” and “Bass

Roll-Off”. An acoustic measuring system such as

WinMLS is recommended for analyzing the effects

of the adjustments, however, careful listening with

suitable test recordings can also lead to good results

if a test system is not available. Table 1 shows some

typical settings in various situations. Figure 4 shows

the effect of the controls on the anechoic response.

Figure 1: Location of the acoustic

axis

Figure 2: Type of cable needed if

unbalanced source is used (ex-

ample shown is RCA output to the

XLR input)

Figure 3: Control and connector layout on the rear panel of

the 8030A.

190 mm

ACOUSTIC

AXIS

> 0,7 m

Product specificaties

Merk:	Genelec
Categorie:	Speaker
Model:	8030A
Kleur van het product:	Wit
Gewicht:	5600 g
Breedte:	189 mm
Diepte:	178 mm
Hoogte:	299 mm
Connectiviteitstechnologie:	Bedraad
Meegeleverde kabels:	AC
Gemiddeld vermogen:	80 W
Aanbevolen gebruik:	Overige
Impedantie:	- Ohm
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Tafelblad/Boekenplank
Aantal drivers:	2
Woofer:	Ja
Frequentiebereik:	55 - 21000 Hz
Gevoeligheid:	100 dB
Luidspreker soort:	2-weg
Totale harmonische vervorming (THD):	2 procent
Versterker:	Ingebouwd
Diameter woofer:	5 "
Diameter hogetonenluidspreker:	0.75 "
XLR in:	Ja
Tweeter:	Ja
Crossover frequentie:	3000 Hz