GE Profile SPSD157JMV Handleiding

GE Niet gecategoriseerd Profile SPSD157JMV

Lees hieronder de 📖 handleiding in het Nederlandse voor GE Profile SPSD157JMV (13 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/13
Installation
Instructions
KIT CONTENTS
4 Support Pads
4 Mounting Screws
Drawer Divider
1
TOOLS YOU WILL NEED
Phillips Head
Screwdriver
9/16″Open End Wrench
or Adjustable Wrench
8 mm Socket Wrench
REMOVE THE LEVELING LEGS
Carefully lay the washer or dryer on its side
to access the leveling legs on the bottom
of the appliance.
IMPORTANT: Do not lay the washer or dryer
on its back! Do not remove the shipping bolts
on the back side of the washer. The bolts must
remain in place until the washer is returned
to an upright position.
Use an open-end wrench to remove the
washer or dryer leveling legs.
B
A
1
INSTALLATION PREPARATION
Remove the packaging.
The Drawer divider is taped at the top of the
shipping carton. Remove the divider and set aside
for final installation.
Flatten the product carton to use as a pad
to lay the washer or dryer down on its side.
Continue using the carton to protect the finished floor
in front of the installation location.
Back out and remove
all 4 leveling legs
Instructions en français : . . . . . . . . . . . . . . . .4
Instrucciones en español: . . . . . . . . . . . . . . .8
Pedestal Models
White Pedestal SPSD157JWW
Metallic Gold SPSD157JMG
Metallic Vermillion SPSD157JMV
For Washer Model: WPDH8800
For Dryer Models: DPVH880EJ, DPVH8800GJ
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•IMPORTANT —Save these instructions
for local inspector’s use.
•IMPORTANT —Observe all governing
codes and ordinances.
• Note to Consumer – Keep these instructions
with your Owner’s Manual for future reference.
• Completion time – 1 to 2 hours
•Proper installation is the responsibility
of the installer.
•Product failure due to improper installation is not
covered under the Warranty.
CAUTION — Due to the size and weight
of these products, and to reduce the risk of
personal injury or damage to the product, TWO
PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.
•See washer and dryer installation instructions for
additional installation requirements and guidelines.
2
Installation Instructions
INSTALL THE PEDESTAL
TO THE WASHER OR DRYER
Place the pedestal against the bottom
of the unit. Check to be sure the drawer front
is at the front of the unit.
Align the holes in the pedestal with the
holes in the bottom of the unit. Use a Phillips
screwdriver to install the 4 screws through the
pedestal and into the unit—do not tighten.
Slide the pedestal toward the unit, until it is
aligned front to back. Use an 8 mm socket
wrench to securely tighten the screws.
C
B
A
3
PREPARE THE PEDESTAL
Pull the
drawer out
as far as it
will go.
Remove screws
from drawer
slides. Slide
drawer out of
the base and
set aside.
FOR DRYERS ONLY:
Locate the 4 support pads from the parts
package. Each pad has 2 protrusions that fit
into the holes on top of the pedestal. Press
the rubber pads into each set of corner holes
on the top of the pedestal as shown.
NOTE: The support pads should be installed on
the dryer only. DO NOT INSTALL THESE PADS ON
THE WASHER PEDESTAL.
C
B
A
2
3
Installation Instructions
LEVEL THE WASHER OR DRYER
Locate the 4 legs from the parts package
and install.
Stand the washer or dryer upright. Move it
close to its final location.
Make sure that the washer or dryer is level
by placing a spirit level on top. Check side
to side and front to back.
Use an open
ended wrench to
adjust the legs
in and out.
Tighten the lock
nut against the
bottom of
the pedestal.
NOTE:
• To minimize vibration, the locking nuts must
be tight.
• To reduce vibration, ensure that all four rubber
leveling legs are firmly touching the floor. Push
and pull on the back right and then the back
left of your washer or dryer.
D
C
B
A
4
REMOVE SHIPPING SCREWS
Remove the 4 shipping screws on the back side
of the unit.
6
REINSTALL THE DRAWER
Check to
be sure the
slides are
closed.
Slide the
drawer
into the
opening.
Align the
drawer
supports to the
slides on each
side.
Reinstall the original screws into each drawer
slide. Tighten both screws.
Open the drawer fully. Slide drawer divider
into slots in the center of the drawer. The
drawer should slide smoothly when you push
it closed.
D
C
B
A
5
FINALIZE THE INSTALLATION
Refer to the washer or dryer Installation Instructions
to complete the installation.
7
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Drawer
divider

Product specificaties

Merk: GE
Categorie: Niet gecategoriseerd
Model: Profile SPSD157JMV

Heb je hulp nodig?

Als je hulp nodig hebt met GE Profile SPSD157JMV stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd GE

GE

GE Profile UCG1600LWW Handleiding

6 December 2023
GE

GE ZWSP42D Handleiding

1 Juli 2023
GE

GE ZGW124ENSS Handleiding

11 Juni 2023
GE

GE Profile GCG1500LBB Handleiding

5 Juni 2023
GE

GE GNULQ Handleiding

24 Mei 2023
GE

GE FXRC1 Handleiding

10 Mei 2023
GE

GE ZX27CTYSS Handleiding

9 Mei 2023
GE

GE ZKHT1 Handleiding

7 Mei 2023
GE

GE GXEM01Z Handleiding

6 Mei 2023
GE

GE ZCG3100VBB Handleiding

6 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Livarno Lux

Livarno Lux IAN 071407 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 317128 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 049213 Handleiding

29 November 2024
Livarno Lux

Livarno Lux ST-1002 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG02489 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG02189 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 365198 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 367074 Handleiding

29 November 2024
Livarno Lux

Livarno Lux HG00701 Handleiding

29 November 2024
Livarno Lux

Livarno Lux IAN 337273 Handleiding

29 November 2024