GE GPF3RACK Handleiding

GE Vaatwasser GPF3RACK

Lees hieronder de đź“– handleiding in het Nederlandse voor GE GPF3RACK (12 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 106 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
1
FOLLOW THE LINK BELOW TO ACCESS AN
INSTRUCTIONAL VIDEO FOR INSTALLING THE
3RD RACK:
http://www.geappliances.com/qr/dishwasher/thirdrack/
Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com
31-31588 05-18 GEA
COMPATIBLE WITH THESE GE APPLIANCES DISHWASHER MODELS:
GDF530PGM, GDF530PSM, GDF530PMM, GDT605PGM, GDT605PSM,
GDT605PMM, GDT605PFM, GDT605PBM, GDP615HSM, GDP615HFM,
GDP615HBM, GDT635HSM, GDT635HMM
Built-In Dishwashers
Installation
Instructions
3rd Rack Installation
BEFORE YOU BEGIN
Read these instructions completely and carefully. FOR YOUR SAFETY
Read and observe all WARNINGS shown throughout
these instructions.
While performing installations described in this booklet,
gloves, safety glasses or goggles should be worn.
IMPORTANT – Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these instructions
for the consumer’s and local inspector’s use.
• – Keep these instructions with Note to Consumer
your Owner’s Manual for future reference.
• – Installation of this kit requires basic Skill Level
mechanical skills. Proper installation is the
responsibility of the installer. Product failure due
to improper installation is not covered under the
GE Appliances Warranty. See Warranty information.
IMPORTANT NOTES
• This kit is for use with GDF530PGM, GDF530PSM,
GDF530PMM, GDT605PGM, GDT605PSM, GDT605PMM,
GDT605PFM, GDT605PBM, GDP615HSM, GDP615HFM,
GDP615HBM, GDT635HSM, GDT635HMM models only.
• This 3rd Rack cannot be used on plastic tub
dishwashers produced before 2018.
• Use a #2 Phillips-head screwdriver to drive all screws.
• Power tools should not be used during the installation of
the 3rd Rack.
• Torque higher than 15 inch pounds will strip the screw
boss.
• The 3rd Rack mount can temporarily support its own
weight with its locator. It CANNOT support the weight
of the rails until screws are driven.
• Consider lowering the upper rack to the lower option
after installing the 3rd Rack
• All the front end hooks of the rails should be pointed
upwards.
• If, at the last step, there is interference between the
3rd Rack and the upper rack, make sure that the
mounts are properly seated against the ceiling of the
tub and
the screws are driven in completely. If the issue
persists,
lower the upper rack to the bottom setting.
• If cup shelves are installed on the upper rack, they should
be removed prior to 3rd Rack installation and use.
TOOL YOU WILL NEED:
#2 Phillips-head screwdriver
IMPORTANT: Do NOT use any power tools
to drive the 3rd Rack screws.
PARTS INCLUDED:
• Mounts (2)
• Rails (2)
• Screws (4)
• 3rd Rack
Tray Assembly (1)
• Rear End Caps (2)
Printed in the United States
READ CAREFULLY - KEEP THESE INSTRUCTIONS
The rail end caps can be a choke
hazard for small children if removed
from the dishwasher. Keep out of reach of children.
WARNING
2
Installation Instructions
1 REMOVE UPPER RACK
• Pull the upper rack out to full extension.
• Lift the rack so the front wheels clear the front end
hooks on each side rail.
• Pull the rack out until the rear wheels contact the
front end hooks on each side rail.
• Lift the rack off the rails.
• The upper rack spray arm should be drained of water
by tilting the rack backwards while holding it over the
sink or over towels.
2 REMOVE UPPER RACK RAILS
(OPTIONAL)
• Pull one upper rack rail out most of the way.
• Remove the rear end cap from the rail by lifting its
center tab and pulling the cap back and off.
• Pull the rail off the roller mounts.
• Repeat on the opposite side.
4 INSTALL 3RD RACK RAILS
• Install the rail by sliding it onto both rack mount
rollers.
• 3rd Rack rails are right and left side specific. To
ensure proper assembly, all front end hooks must
point upwards.
• Attach the rear end cap by snapping it onto the back
of the rail.
• Ensure rear end cap is properly assembled by
listening for a definite “click” sound and giving a
gentle outward pull on the rail to verify retention.
• Repeat on the opposite side.
Pull out,
lift up, and
remove
Pull out
rail
Remove rear
end cap
Tab
3 INSTALL 3RD RACK MOUNTS
• Insert the locating tab of the 3rd Rack mount into the
tub slot and fully seat against the ceiling of the tub.
• Be sure the tub mount is flush with the side wall of
the tub.
• Part will temporarily retain itself in the tub until screws
are installed.
• Align the screw holes and use a Phillips screwdriver
to drive one of the provided screws into each screw
hole.
DO NOT USE POWER TOOLS OR OVERTIGHTEN.
• Repeat on the opposite side.
Slide rail onto
rollers
Replace rear
end cap
3
Installation Instructions
6 RE-INSTALL UPPER RACK RAILS
(IF REMOVED IN STEP 2)
• Slide the rails back onto their mounts so that both
wheels are within the rail.
• Make sure the front end hook is facing up.
• Attach the rear end caps to the end of the rails.
• Ensure rear end cap is properly assembled by
listening for a definite “click” sound and giving a
gentle outward pull on the rail to verify retention.
.
• Repeat on the opposite side.
7 RE-INSTALL UPPER RACK
• Fully extend the upper rack rails.
• Tilt upwards the front of the upper rack and place the
rear rack rollers over the front end hooks.
• Push the upper rack along the rails until the front
rack rollers clear the front end hooks.
• Lower the upper rack onto the rails and slide into the
tub.
• Check that the upper rack is properly engaged by
rolling it in and out several times.
• Make sure there is no interference between the 3rd
Rack and upper rack.
• If interference is present, remove the upper rack and
inspect the 3rd Rack mounts and screws to ensure
they are fully seated. If the issue persists after
re-installing the upper rack, consider lowering the
upper rack to the bottom position.
Slide rail onto
rollers
Replace rear
end cap
Place rack wheels over front
end hooks and slide in
5 INSTALL 3RD RACK INTO RAILS
• Fully extend both 3rd Rack rails.
• Tilt the front of the 3rd Rack tray assembly upwards
and place its rear wheels just behind the front end
hooks.
• Slide the 3rd Rack onto the rails until the front
wheels clear the front end hooks.
• Lower the 3rd Rack and push it into the tub.
• Check that the 3rd Rack is properly engaged by
rolling it in and out several times. When properly
assembled, the 3rd Rack tray should extend fully
outward past the front edge of the dishwasher tub.
Push
rack in
Tilt
front
up
Place over front end
hooks and slide in
Roller wheels indicate rear
of 3rd Rack

Product specificaties

Merk: GE
Categorie: Vaatwasser
Model: GPF3RACK

Heb je hulp nodig?

Als je hulp nodig hebt met GE GPF3RACK stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Vaatwasser GE

GE

GE Café CXADTH1PMSS Handleiding

7 December 2024
GE

GE Café CXADTH1PMFB Handleiding

7 December 2024
GE

GE PDT755SYRFS Handleiding

15 November 2024
GE

GE PDP755SYRFS Handleiding

15 November 2024
GE

GE CDT888P2VS1 Handleiding

19 Maart 2024
GE

GE CDP888M5VS5 Handleiding

19 Maart 2024
GE

GE Profile PDT145SGLWW Handleiding

6 December 2023
GE

GE Profile PDT145SSLSS Handleiding

6 December 2023
GE

GE Profile PDW7880NSS Handleiding

6 December 2023
GE

GE CDT765SSFSS Cafe Handleiding

7 Oktober 2023

Handleiding Vaatwasser

Nieuwste handleidingen voor Vaatwasser

Bosch

Bosch SBV4HBX23E Handleiding

20 December 2024
Equator

Equator GD 075 Handleiding

19 December 2024
Bauknecht

Bauknecht OBIC Ecospace 8650 Handleiding

18 December 2024
Bauknecht

Bauknecht B2I HKD524 AS Handleiding

18 December 2024
Teka

Teka DFI 46730 Handleiding

17 December 2024
Teka

Teka DFI 46720 Handleiding

17 December 2024
Junker

Junker JB55X02ITE Handleiding

16 December 2024
Junker

Junker JB55X01ITE Handleiding

16 December 2024
Junker

Junker JB55X01HTE Handleiding

16 December 2024
Junker

Junker JB65X00HTE Handleiding

16 December 2024