GE GPF100 Handleiding

GE Vaatwasser GPF100

Lees hieronder de đź“– handleiding in het Nederlandse voor GE GPF100 (2 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 83 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Before you begin – Read these instructions completely and carefully.
IMPORTANT: Save these instructions for local inspector’s use.
IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer.
NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future reference.
WARNING
To prevent electric shock, discon-
nect electrical power supply to
dishwasher before changing
springs. Do not operate dish-
washer while changing panels or
when lower access panel assembly is removed.
Tools and Materials required:
• 1/4" socket driver
• Phillips screwdriver
• Gloves to protect against sharp edges
STEP 1:
• Turn off water supply.
• Latch dishwasher door.
• Turn off Power supply.
STEP 2:
Remove lower access panel assembly
• Remove the two screws below the access panel.
Retain screws.
• Loosen the two screws located between the door and
the access panel. Do not attempt to remove these
screws. They are secured to the access panel with
washers.
• Remove the access panel assembly and toekick from
the dishwasher. Set aside.
Installation Instructions For
GPF100 Dishwasher Door Spring Kit
For installation of a custom dishwasher door panel weighing 4 pounds to 8 pounds
GPF100 Kit
TYPE 1
2 springs 7-1/8” long
TYPE 2
2 springs 5-7/8” long and 2 plastic links
Loosen 2 Screws
Door
Panel
Access Panel
Toekick
This kit contains two sets of springs to accommodate
different door counter-balance systems on dishwash-
ers. Use the type appropriate for your particular
dishwasher.
Pub. No. 31-30504 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE DWG. NO. 206C1559P041
(N.D. 315) 11/98
STEP 3:
Remove old springs
• Grasp the end of the spring at the rear of the dish-
washer and release the hook.
• Release opposite end of the spring and remove.
Note:
The open end of the spring hook should face the outside
of the dishwasher to prevent spring coils from rubbing against
adjacent cabinet wall.
TYPE 1
• Place long end of the spring hook onto the hinge
arm pin.
• Stretch the short end of spring and hook into the
second hole from the front of the channel.
• Repeat the same procedure for the opposite side.
TYPE 2
• Place the long end of the spring hook into the link and
place plastic link onto the hinge arm hook. Use link
provided in this kit, or reuse dishwasher supplied link.
• Stretch the short end of spring and hook into the
second hole from the front of the channel.
• Repeat the same procedure for the opposite side.
STEP 5:
Check door balance
• Open and close the door to check for proper balance.
Correct spring tension should prevent the door from
rising by itself from a full open position and prevent the
door from falling heavily.
• If the door falls heavily, increase the spring tension by
moving one spring back to the next hole.
– Test balance again. Move the opposite spring back if
necessary. If more tension is required, move one or both
springs to the last hole.
• If the door rises on its own, from a full open position,
decrease the tension by moving one or both springs
forward.
STEP 6
• Reinstall toekick and access panel.
• Turn water on.
• Turn electrical power on.
STEP 4:
Install new springs
• Determine if your dishwasher has a Type 1 or Type 2
counter-balance system.
Insert Spring Hook
Through Inside of Frame
Plastic
Link
Insert Spring Hook
Through Inside of Frame
More Tension Less Tension


Product specificaties

Merk: GE
Categorie: Vaatwasser
Model: GPF100

Heb je hulp nodig?

Als je hulp nodig hebt met GE GPF100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vaatwasser GE

Handleiding Vaatwasser

Nieuwste handleidingen voor Vaatwasser