GE DRSR495EGWW Handleiding

GE Wasdroger DRSR495EGWW

Lees hieronder de 📖 handleiding in het Nederlandse voor GE DRSR495EGWW (8 pagina's) in de categorie Wasdroger. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Installation

Instructions

Electric Dryer

TOOLS YOU

WILL NEED

MATERIALS YOU WILL NEED

PHILLIPS SCREWDRIVER

SLIP JOINT PLIERS

LEVEL

GLOVES

SAFETY

GLASSES

DRYER POWER

CORD KIT

(NOT PROVIDED

WITH DRYER)

4" DUCT

CLAMPS (2)

4" SPRING

CLAMPS (2)

EXHAUST

HOOD

NOTE: Installation and service of this dryer requires basic

mechanical and electrical skills. It is your responsibility to

contact a qualified installer to make the electrical connections.

3/4" STRAIN

RELIEF

UL RECOGNIZED

4" DIA. METAL

ELBOW

Step 1 Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Step 2 Check and Ensure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Speciﬁcations (see section 3).

Step 3 Remove the Foam Shipping Pads (see section 1).

Step 4 Move the Dryer to the Desired Location.

Step 5 Connect the Power Supply (see section 2).

Step 6 Connect the External Exhaust (see section 4).

Step 7 Level Your Dryer (see section 5).

Step 8 Check the Operation of the Power Supply

and Venting.

Step 9 Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By the Owner.

For Alcove or Closet Installation, see section 6.

For Bathroom or Bedroom Installation, see section 7.

For Mobile or Manufactured Home see, section 8.

For side or bottom exhaust, see section 9.

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

FLAT BLADE SCREWDRIVER

DUCT TAPE

WARNING RISK OF FIRE

• To reduce the risk of severe injury or death, follow all installation instruc-

tions.

• Clothes dryer installation must be performed by a qualified installer.

• Install the clothes dryer according to these instructions and in accordance

with local codes.

• This dryer must be exhausted to the outdoors.

• Use only 4” rigid metal ducting for exhausting the clothes dryer to the

outdoors.

• Do not install or store this appliance in any location where it could be

exposed to water and or weather.

• Save these instructions. (Installers: Be sure to leave these instructions with

the customer).

• DO NOT install a clothes dryer with flexible plastic ducting materials. If

flexible metal (semi-rigid or foil-type) duct is installed, it must be UL listed

and installed in accordance with the instructions found in "Connecting The

Dryer To House Vent" on page 5 of this manual. Flexible venting materials

are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct dryer airflow and increase the risk of fire.

Questions on Installation? Call: 1-800-GECARES (US)

www.GEAppliances.com (US)

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•IMPORTANT- Save these

instructions for local inspector’s use.

•IMPORTANT- Observe

all governingcodes and ordinances.

• Note to Installer - Be sure to leave these

instructions with e omth cust er.

• Note to Customer - Keep these instruct-

ions with your Use and Care Book for

future reference.

• Before the old dryer is removed from

service or discarded, remove the dryer

door.

• Service information and the wiring dia-

•

gram are located in the control console.

• Do not allow children on or in the appli-

ance. Close supervision of children is

necessary when the appliance is used

near children.

Install the dryer where the temperature

is above 50°F for satisfactory operation of

the dryer control system.

UL RATED

120/240V,30A

WITH 3 OR 4 PRONGS.

IDENTIFY THE PLUG

TYPE AS PER THE

HOUSE RECEPTACLE

BEFORE PURCHASING

LINE CORD.

Installation Instructions

1 PREPARING FOR INSTALLATION

OF NEW DRYER

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear. Consideration

must be given to provide adequate clearance for installation and service.

2 ELECTRICAL CONNECTION

INFORMATION

TIP: Install your dryer before installing your washer.

This will allow better access when installing dryer exhaust.

REMOVING LINT FROM WALL

EXHAUST OPENING

TILT THE DRYER SIDEWAYS

AND REMOVE THE FOAM

SHIPPING PADS BY

PULLING AT THE SIDES

AND BREAKING THEM

AWAY FROM THE DRYER

LEGS. BE SURE TO

REMOVE ALL OF THE

FOAM PIECES AROUND

THE LEGS.

• DO NOT E AN EXTENSION CORD OR ANUS

ADAPTER PLUG WITH THIS A LIANCE.PP

Dryer must be electrically grounded in accordance with

local codes and ordinances, or in the absence of local

codes, in accordance with the NAT NAL ELECTRI-IO

CAL C E, ANSI/NFPA NO. 70. OD

WAR NG - TO DUCE THE RISK OFNI RE

FIRE, ELECTRICAL SHOCK AND PERSONAL

I URY:NJ

ELECTRICAL REQUIREMENTS

This dryer must be connected to an individual branch circuit,

protected by the required time-delay fuses or circuit breakers. A

four or three-wire, single phase, 120/240V or 120/208V, 60Hz,

30 amp circuit is required.

If the electric supply does not meet the above speciﬁcations, then

call a licensed electrician.

GROUNDING INSTRUCTIONS

This dryer must be connected to a grounded metal, permanent

wiring system, or an equipment-grounding conductor must be run

with the circuit conductors and connected to the equipment-

grounding terminal on the appliance.

RELOCATE GREEN

GROUND SCREW

HERE

STRAIN

RELIEF

BRACKET

GREEN OR

YELLOW WIRE

3/4", UL

RECOGNIZED

STRAIN RELIEF

HOT

WIRE

SCREWS

(3)

HOT

WIRE

COVER

NEUTRAL

(White)

REMOVE GROUND STRAP

AND DISCARD. KEEP GREEN

GROUND SCREW

4 #10 AWG MINIMUM COPPER

CONDUCTORS OR 120/240V 30A POWER

SUPPLY CORD KIT MARKED FOR USE

WITH DRYERS & PROVIDED WITH

CLOSED LOOP OR SPADE TERMINALS

WITH UPTURNED ENDS (NOT SUPPLIED).

INTERNAL DUCT

OPENING CHECK THAT EXHAUST

HOOD DAMPER OPENS

AND CLOSES FREELY.

WALL

WARNING:Only a 4-conductor cord shall be used when the

appliance is installed in a location where grounding through the

neutral conductor is prohibited. Grounding through the neutral is

prohibited for the new branch-circuit installations, mobile homes,

recreational vehicles, and areas where local codes prohibit

grounding through the neutral conduction.

CONNECTING DRYER USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTES: SInce January 1,1996, the National Electric code requires

that the new constructions utilize a 4-wire connection to

an electric dryer

Remove and discard existing plastic or metal foil

transition duct and replace with UL listed transition

duct.

•

Installation Instructions

1. Turn off the circuit breaker(s) (30 amp) or remove the dryer’s

circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall.

3. Remove the power cord cover located at the lower back.

4. Install 3/4 in. UL recognized strain relief to power cord

entry hole. Bring power cord through strain relief.

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

6. Be sure ground strap is connected to neutral (center)

terminal of block and to green ground screw on cabinet

rear. Tighten all terminal block screws (3) completely.

7. Properly secure power cord to strain relief.

8. Reinstall the cover.

CONNECTING DRYER USING 3-WIRE

CONNECTION

STRAIN RELIEF

BRACKET

3/4", UL

RECOGNIZED

STRAIN RELIEF

HOT

WIRE

HOT

WIRE

GROUND

STRAP

GREEN

GROUND

SCREW

NEUTRAL

(White)

SCREWS

(3)

IF REQUIRED, BY LOCAL CODE,

INSTALL EXTERNAL GROUND

(NOT PROVIDED) TO GROUNDED

METAL, COLD WATER PIPE, OR

OTHER ESTABLISHED GROUND

DETERMINED BY A QUALIFIED

ELECTRICIAN.

COVER 3 #10 AWG MINIMUM COPPER

CONDUCTORS OR 120/240V 30A POWER

SUPPLY CORD KIT MARKED FOR USE

WITH DRYERS & PROVIDED WITH CLOSED

LOOP OR SPADE TERMINALS WITH

UPTURNED ENDS (NOT SUPPLIED).

1. Turn off the circuit breaker (s) (30 amp) or remove the dryer’s

circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall receptacle.

3. Remove the power cord cover located at the lower back.

4. Remove and discard ground strap. Keep the green

ground screw for step 7.

5. Install 3/4 in. UL recognized strain relief to power

cord entry hole. Bring power cord through strain relief.

6. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of

the terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

7. Attach ground wire of power cord with the green ground

screw (hole above strain relief bracket). Tighten all

terminal block screws (3) completely.

8. Properly secure power cord to strain relief.

9. Reinstall the cover.

WARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK.

WARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK.

EXHAUST SYSTEM CHECK LIST

HOOD OR WALL CAP

• Terminate in a manner to prevent back drafts or entry of birds or

other wildlife.

• Termination should present minimal resistance to the exhaust air flow

and should require little or no maintenance to prevent clogging.

•Never

install a screen in or over the exhaust duct.

This could cause lint build up.

• Wall caps must be installed at least 12 in. above ground level or any other

obstruction with the opening pointed down.

SEPARATION OF TURNS

For best performance, separate all turns by at least 4 ft. of straight duct,

including distance between last turn and exhaust hood.

TURNS OTHER THAN 90º

• One turn of 45º or less may be ignored.

• Two 45º turns should be treated as one 90º turn.

• Each turn over 45º should be treated as one 90º turn.

SEALING OF JOINTS

• All joints should be tight to avoid leaks. The male end of each section of

duct must point away from the dryer.

• Do not assemble the ductwork with fasteners that extend into the duct.

They will serve as a collection point for lint.

• Duct joints can be made air and moisture-tight by wrapping the

overlapped joints with duct tape.

• Horizontal runs should slope down toward the outdoors ½ inch per foot

INSULATION

Duct work that runs through an unheated area or is near air conditioning

should be insulated to reduce condensation and lint build-up.

3 EXHAUST INFORMATION

WARNING - IN CANADA AND IN THE UNITED

IS 4 IN (102mm). DO NOT USE DUCT LONGER

STATES, THE REQUIRED EXHAUST DUCT DIAMETER

THAN SPECIFIED IN THE EXHAUST LENGTH TABLE.

Using exhaust longer than specified length will:

• Increase the drying times and the energy cost.

• Reduce the dryer life.

• Accumulate lint, creating a potential fire hazard.

The MAXIMUM ALLOWABLE duct length and number of

bends of the exhaust system depends upon the type of duct,

number of turns, the type of exhaust hood (wall cap), and all

conditions noted below. The maximum duct length for rigid

metal duct is shown in the table below.

The correct exhaust installation is YOUR RESPONSIBILITY.

Problems due to incorrect installation are not covered

by the warranty.

EXHAUST LENGTH

4" DIA.

2-1/2"

Remove and discard existing plastic or metal foil transition

duct and replace with UL listed transition duct.

Product specificaties

Merk:	GE
Categorie:	Wasdroger
Model:	DRSR495EGWW

Heb je hulp nodig?

Als je hulp nodig hebt met GE DRSR495EGWW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasdroger GE

GE FPDW1 Handleiding

7 December 2024

GE SBSD137HMS Handleiding

7 December 2024

GE GFD40ESCMWW Handleiding

30 November 2024

GE PFD95ESPWGN Handleiding

23 September 2024

GE SPLK10N01A Handleiding

23 September 2024

GE ETD48EASWWB Handleiding

27 Juni 2024

GE GTD48GASWWB Handleiding

16 April 2024

GE GTD48EASWWB Handleiding

16 April 2024

GE GTD38EASWWS Handleiding

16 Maart 2024

GE Profile PFD87GSPVRS Handleiding

16 Maart 2024

Handleiding Wasdroger

Nieuwste handleidingen voor Wasdroger

Svan SSB800A2DB Handleiding

21 December 2024

Haier HD100-A3959E-IT Handleiding

20 December 2024

Haier HD100-A3959RE-IT Handleiding

20 December 2024

Bosch WTN832M1NL Handleiding

17 December 2024

Ufesa Pro Ionic-Shine Handleiding

17 December 2024

Ufesa Pro Ionic Style Handleiding

17 December 2024

Altus ADP80W Handleiding

17 December 2024

BEKO B5T69233MG Handleiding

15 December 2024

AEG T65170AV Handleiding

12 December 2024

Haier HD90-A3979NU1 Handleiding

10 December 2024