GE 15250 Handleiding

GE Tijdschakelklok 15250

Lees hieronder de 📖 handleiding in het Nederlandse voor GE 15250 (3 pagina's) in de categorie Tijdschakelklok. Deze handleiding was nuttig voor 62 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

SPECIFICATIONS

Input Voltage: 120 VAC, 208/240 VAC, or 277 VAC in all units based

upon dipswitch conﬁguration.

15252 NEMA 3R Indoor & Outdoor BM-A301US5-O2

15253, 15251 NEMA 1 Indoor BM-A301US5-I2

15250 NEMA 3R Indoor & Outdoor EM-A301US9-O2

Switch Rating: DPDT Models

Normally Open Contacts

40A Resistive, 120-277Vac.

30A General Purpose, 120-277Vac.

20A Resistive, 30Vdc

1 HP, 120Vac ; 2HP, 240Vac

20A Ballast, 120-277Vac.

15A Tungsten, 120Vac

800VA, Pilot Duty, 120Vac.

720VA, Pilot Duty, 240Vac.

TV-5, 120Vac

Normally Closed Contacts

30A Resistive, 120-277Vac

15A General Purpose, 120-277Vac

15A Resistive, 30Vdc

20A Ballast, 120-277Vac

1/4HP, 120Vac; 1/2HP, 208-240Vac.

290VA, Pilot, 120Vac.

360VA, Pilot, 208-240Vac.

NOTE: If loads are connected to both NC and NO contacts, both contacts are

derated to 67% of the above values.

ENVIRONMENTAL RATINGS

Ambient Temperature: –40F to 130F

Humidity: 0-95% RH, Non-condensing

WIRING CONNECTIONS

Screw clamp terminals for up to 2 AWG #8 wires per position. For supply

connections, use 8AWG or larger wires suitable for at least 105° C. Use copper

conductors only.

LIGHTS

Power LED (Orange) – Light illuminates when power is applied to

the timer

Status LED (Green) – Light illuminates when power is applied to load.

INSTALLATION

CAUTION: Before wiring or service, power to this time switch and the

equipment it controls must be turned off. Turning off the timer switch only

will not prevent a shock hazard. Replace cover plate within housing before

supplying power to time switch. Installation should be performed by a licensed

electrician only. Before installing this product read all instructions carefully.

Remove protective cover panel within time switch housing by removing

screws located above timer face and at the bottom of the cover panel.

DIPSWITCH CONFIGURATION

WARNING: Failure to properly conﬁgure the dipswitch will result in

damage to the unit and void the warranty! Before installing and wiring the GE

Time Switch, proper conﬁguration must be selected. This is accomplished as

follows:

INPUT VOLTAGE DIP SWITCH SETTING:

1. Do not apply power to the timer prior to setting correct Input Voltage DIP

switch.

2. Determine the input voltage which will be applied to the timer (i.e. L1 and

L2/N terminals, see wiring diagrams)

3. Set the DIP switch according to the diagram below.

NOTE: Unit is shipped with DIP switches set for 277VAC Input Voltage

CAUTION: Do not check circuits by “sparking” wires to terminals. Damage to

the timer may result.

Digital Time Switch

15250

Indoor/Outdoor

NEMA 3R-Rated

Enclosure

NOTE: For outdoor locations (model GE 15252),, rain tight or wet location

conduit hubs that comply with requirements of UL 514B (standard for ﬁttings

for conduit and outlet boxes) must be used.

1. Remove 2 screws retaining the interior cover panel and remove panel

by prying out with a thin blade at the top.. Select knockouts to be used.

Remove the inner 1/2” knockout by inserting a screwdriver in the slot

and carefully punch knockout loose. Remove slug. If the 3/4” knockout

is required, remove the outer ring with pliers after removing the 1/2”

knockout. Smooth edges with knife if necessary.

2. Place enclosure in desired mounting location and mark the three

mounting holes.

3. Drill holes for #10 screws, start screws in holes.

4. Place enclosure over screws and tighten screws.

5. Connect conduit hubs to conduit before connecting the hubs to the

enclosure. After inserting hubs into enclosure, carefully tighten hub lock

nut. Do not over-tighten.

6. Install in accordance with all applicable National and Local code

requirements. See Figure 1 and wiring diagrams.

7. Replace interior cover panel and 2 screws.

GROUNDING: This enclosure is of plastic construction and does not

require a ground connection and does not require bonding in pool

applications.

This enclosure does not provide grounding between conduits. When using

non-metallic conduit or cable, connect the ground wires of all cables together

with a wire nut. When metallic conduit is used, use grounding type bushings

and a jumper wire between each conduit.

120VAC

277VAC (Default)

208~240VAC

NOTE: Unit is shipped with DIP Switches set for 277VAC Input Voltage.

CAUTION: Do not check circuits by “sparking” wires to terminals. Damage to

the timer may result.

INPUT VOLTAGE DIP SWITCH SETTING:

1. Do not apply power to the timer prior to setting correct Input Voltage DIP switch.

2. Determine the input voltage which will be applied to the timer (i.e. L1 and L2/N terminals,

see wiring diagrams).

3. Set the DIP Switch according to the diagram below.

http://waterheatertimer.org/GE-timers-and-manuals.html

TIMERN CN O

COM

NC2

NO2

COM2

LOAD

TIMERN CN O

COM

TO 200/240/277V LINE

TO 120V LINE

NC2

NO2

COM2

LOAD

TIMERN CN O

COM

TO 24V LINE

NC2

NO2

COM2

LOAD

TO 120V LINE

TO LOAD

120V Timer, 120V Load and 24V Load

Wired as Single Throw

200/240/277V Timer, 200/240/277V Load, Double Break

Wired as Single Throw

120V Timer, 200/240/277V Load Double Break

Wired as Single Throw

Typical Wiring Diagrams—DPDT

TO POWER SUPPLY

TO POWER SUPPLY 1 TO POWER SUPPLY 2

Timer and Load, Same Voltage

Wired as Single Throw

TO LOAD

TO 120V LINE

HIGH

LOW

COM

LOAD

NCTIMERN OC OM

TIMERN CN OC OM

120V Two Speed Fan

Wired as Double Throw

Timer and Load, Different Voltage

Wired as Single Throw

Typical Wiring Diagrams—SPDT

Field Wiring

Timer Internab Wiring

FIGURE 1

Override

(Manual ON/OFF Switched)

Timer

(9 Programs Setting)

Clock

(Current Time Setting)

LCD

(Function Figures)

(Reset)

H-

(Hours Setting)

M-

(Minutes Setting)

Day

(Days Setting)

OPERATING INSTRUCTIONS

BASIC SETTINGS:

Initial Set Up:

1. Push the “R” button before programming to clear out any settings. Once

the “R” button is pressed the screen will begin to ﬂash. A paperclip may

be needed for this step.

(If the “R” button appears to stick down, use a toothpick to maneuver

it until it pops back up. The screen will ﬂash if the button is popped up

successfully.)

2. Press the “Clock” button and the screen will stop ﬂashing and be ready

for programming.

Setting the Current Time:

1. Press and Hold the “Clock” button during the entire setting.

2. Press the “H+” button to set the hours.

3. Press the “M+” button to set the minutes.

4. Press the “Day” button to set the day of the week.

5. Release the “Clock” button.

Programming ON/OFF Settings:

1. Press the “Timer” button once and the TIMER 1 ON - - : - - appears.

2. Press the “H+” and “M+” button to set the hours and minutes to the

desired time.

3. Press the “Day” button to select the day(s) the setting will be active. Refer

to the Multiple Weekday Group below to see the available settings.

4. Press the “Timer” button to store the setting and proceed to the next

setting TIMER 1 OFF - - : - -.

5. Repeat for all remaining setting options (9 Total ON/OFF settings). Once

completed press the “Clock” button to return to the main display.

Multiple Weekday Groups:

Apart from individual week days, pressing the “Day” button also selects

multiple day combinations such as:

- Monday thru Friday - Tuesday & Thursday & Saturday

- Saturday & Sunday - Monday thru Wednesday

- Monday thru Saturday - Thursday thru Saturday

- Monday & Wednesday & Friday - Monday thru Sunday

After setting a single day or a multi-day-combination the programmed timer

settings will be carried out on each of the week-days at the same time.

Programming Countdown Operation:

1. Press the “Timer” button to scroll through the 9 events settings to get to

the ON C setting.

2. Press the “Override” button to select whether the timer will turn ON or OFF

during teh countdown period.

3. Press the “H+” and “M+” buttons to set the hours and minutes of the

countdown.

4. Press the “Clock” button to store the setting and return to the current time

display. See the diagram below for more information.

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

MINIMUM

COPPER

WIRE SIZE

(AWG)

MAX.

LOAD

(AMP)

MIN.

INSUL-

ATION

TEMP(°C)

75°C INSULATION MAX. MOTOR

LOAD (HP)

SINGLE PHASE 3 PHASE

120 V. 240 V. 208 V. 240 V.

105

1/2

2 1/2

N/A

ADVANCED SETTINGS

Activate the Countdown Feature:

1. Press the “Clock” and “Override” button at the same time to

start the countdown function.

2. Press the “Override” button to pause and continue the

countdown function.

3. Press the “Clock” button to go view the current time display.

Manual Override:

The timer comes with the ability to control the ON and OFF function while the

timer is deactivated. Press and Hold the “Override” button to switch between

timer mode and manual mode. Timer mode will be indicated by an A next to

the ON or OFF. When the timer is in manual mode (not controlled by timer) the

A will not appear on the display. Any time the “A” is on the display the timer is

in control and will always follow the programmed settings (even if it

is temporarily deactivated by moving from ON to OFF or OFF to ON).

Random, ON/OFF Setting:

This feature allows the timer to switch ON and OFF at random times. It is

particularly useful in helping to prevent house burglary as the timer is not

switching ON and OFF at regular times. The programmed settings set will be

executed in a random delay varying within 30 minutes. This function will only

operate if one or more programmed switching commands are set.

1. Press both “Day” and “H+” buttons at the same time. The display will show

the “TIMER” symbol blinking. The random feature is now activated.

2. To turn the random feature off repeat step 1.

Summer Time Feature (DST):

Press the “H+” and “M+” buttons for 3 seconds to advance the current time

1 hour, SUMMER should appear on the display. Repeating this process will

decrease the time by 1 hour and the SUMMER will disappear.

Power Back Up Feature:

In the event of a power failure, the timer will retain its settings for an

estimated 3 months assuming the power back up is fully charged.

Button Lock:

This function allows the user to lock the buttons so that they are not

accidentally pressed.

1. Press and HOLD the “Clock” button for more than 5 seconds. An

“ “ icon will appear on the display. The buttons are now locked.

2. To unlock the buttons repeat this step.

Note:

“ “ Flashing: the timer is in the manual mode with key lock.

“ “ Not ﬂashing: the timer is in the timer mode with key lock.

Lockout a Programmed Setting (Skip a Setting):

1. Press the “Timer” button to scroll to the setting that needs to be skipped.

2. Press the “Override” button to lockout the time setting. The display will

display “H I : d E” and lock the hours and minutes setting.

3. Press the “Override” button again to recall the setting time.

(Will not work for Lockout Countdown feature)

Product specificaties

Merk:	GE
Categorie:	Tijdschakelklok
Model:	15250

Heb je hulp nodig?

Als je hulp nodig hebt met GE 15250 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Tijdschakelklok GE

GE 56922 Handleiding

30 Juli 2023

GE 15136 Handleiding

30 Juli 2023

GE 15250 Handleiding

30 Juli 2023

Handleiding Tijdschakelklok

Nieuwste handleidingen voor Tijdschakelklok

Sygonix 1625525 Handleiding

16 Oktober 2023

Sygonix 1528595 Handleiding

16 Oktober 2023

TimeControl AX-801 Handleiding

2 Oktober 2023

TimeControl DX-2 Handleiding

2 Oktober 2023

Wachsmuth - Krogmann WK140A Handleiding

29 September 2023

Wachsmuth - Krogmann WK 075 Handleiding

29 September 2023

Wachsmuth - Krogmann WK140C Handleiding

29 September 2023

Wachsmuth - Krogmann WK88 Handleiding

29 September 2023

Goobay 51276 Handleiding

21 September 2023

Goobay 55546 Handleiding

21 September 2023