GBC HeatSeal Sprint H925 Handleiding

GBC Lamineersysteem HeatSeal Sprint H925

Lees hieronder de 📖 handleiding in het Nederlandse voor GBC HeatSeal Sprint H925 (27 pagina's) in de categorie Lamineersysteem. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/27
To register this product go to www.gbc.com
Pour enregistrer ce produit allez sur www.gbc.com
Para registrar este producto vaís en www.gbc.com
To register this product go to www.gbc.com
Pour enregistrer ce produit, allez sur www.gbc.com
Para registrar este producto visite www.gbc.com
H925
Instruction Manual
Manuel d’instructions
Manual de instrucciones
HeatSeal® SprintTM
2
A) Feed Tray
Plateau dalimentation
Bandeja de alimentación
B) Paper Side Guide
Guide latéral pour le papier
Ga lateral del papel
C) Top Cover
Couvercle supérieur
Tapa superior
D) Control Panel
Panneau de commande
Panel de control
E) Exit Tray
Plateau de sortie
Bandeja de salida
F) Power Button
Touche dalimentation
Botón de encendido
G) 4 EZloadTM Levers
4 leviers de chargement EZloadTM
4 palancas de carga EZload
TM
H) Heat Button
Touche de chauffage
Botón “Heat (de calentamiento)
I) Feed Switch
Interrupteur d’alimentation
Interruptor Feed (de alimentación)
J) Idler Bar Assembly
Assemblage de barre de transfert
Conjunto de barra intermediaria
K) Heat Shoe
Sabot chauffant
Zapata térmica
L) Film Roll
Rouleau de pellicule
Rollo de pecula
M) Ready (LED)
Voyant d’état « Prêt » (DEL)
LED “Ready” (Lista)
N) Power
Voyant d’alimentation
Encendido
O) Start Button
Touche de marrage
Botón “Start (Inicio)
P) Alert (LED)
Voyant d’alerte (DEL)
LED “Alert (Alerta)
Q) Low Film (LED)
Voyant de faible quantité
de pellicule (DEL)
LED “Low Film” (Poca
película remanente)
R) Stop Button
Bouton d’arrêt
Botón de Paro
S) Film Select Buttons
Touches de sélection de
pellicule
Botones de selección de
película
HeatSeal Sprint Description/ H925 -
Description/Descripción
TM®
limenta
B
A
C
D
E
S
O
M
N
P
Q
F
G
H
I
J
L
K
R
Start/Start/Inicio Stop/Stop/Interrupción
3 mil / 75 mic 5 mil / 125 mic
4
Perform only the routine maintenance procedures referred to
in these instructions.
The only maintenance required by the operator is to periodically clean the heat
shoes. This should only be done when changing film rolls, please see page 7
steps 1,2, & 3. The following procedure will help keep the heat shoes free of
adhesive that has been deposited along the edge of the laminating film.
Preheat the laminator using the heat button.
Clean the top and bottom heat shoes with a soft cloth.
Follow the procedure on page 7, steps 4,5,6 and 7.
Unplug the unit and contact an authorized GBC service representative
for any required repairs if one or more of the following has occurred:
Service
Caring for the H925 Laminator
Installation
Do not attempt to service or repair the laminator.
WARNING: THIS IS NOT A TOY - DO NOT ALLOW CHILDREN
TO OPERATE THIS LAMINATOR!
CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED
WHILE THE LAMINATOR IS HOT. USE EXTREME CAUTION.
NOTE: Do not use metal scouring pads to clean the heat shoes!
WARNING: Do not laminate glitter and/or metallic items.
Damage to the rollers may result.
WARNING: Do not apply cleaning fluids or solvents
to the rollers.
WARNING: Do not attempt to laminate adhesives
marked ‘Flammable’.
The power supply cord or attachment plug is damaged.
• Liquid has been spilled into the laminator.
The laminator is malfunctioning after being mishandled.
The laminator does not operate as described in these instructions.
• Shipping damage should be brought to the immediate attention of
the delivering carrier.
• Place the laminator on a stable at surface capable of supporting
110 lbs/50 kg. The surface should be at least 30" high to assure
comfortable positioning during operation. All four rubber feet should
be on the supporting surface.
• Connect power cord to an appropriate power source. Avoid
connecting other equipment to the same branch circuit to which
the laminator is connected as this may cause nuisance tripping
of the circuit breaker or blown fuses.
• Position laminator to allow documents to exit freely.
• If laminating letter/A4 size documents, open exit tray to fully
extended position. When laminating any media that is longer
than letter/A4 in the landscape orientation – the exit tray MUST be
folded back into the machine. Failure to do so will result in a jam
caused by the finished media not having enough room to clear the
rollers once laminated.
• Install this laminator where the ambient temperature is at least
72°F/22°C.
1
2
3
HeatSeal Sprint Safety H925 -
TM®


Product specificaties

Merk: GBC
Categorie: Lamineersysteem
Model: HeatSeal Sprint H925

Heb je hulp nodig?

Als je hulp nodig hebt met GBC HeatSeal Sprint H925 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Lamineersysteem GBC

Handleiding Lamineersysteem

Nieuwste handleidingen voor Lamineersysteem