Garmin GPS 165 Handleiding

Garmin Navigator GPS 165

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Garmin GPS 165 (4 pagina's) in de categorie Navigator. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
GPS 155/165
PILOTā€™S GUIDE
ADDENDUM
1. ROUTE RAIM PREDICTION FUNCTION
The GARMIN GPS 155/165 software versions 3.09 and higher incorporate a change to add the Route RAIM Prediction
Function ( ). This change evaluates the enroute RAIM availability over the entire route that the pilot intends toRAIM prd
fly. This enhancement meets the minimum system requirements required to conduct BRNAV/RNP-5 Operations (FAA
Advisory Circular 90-96).
1. From the Route Catalog Page (Figure 1), select the desired route for RAIM prediction (if the route is empty, enter
the route first). Highlight the route action field, select and press . The Route RAIMā€˜RAIM prdā€™ ENTER
Prediction Page will be displayed (Figure 2).
Figure 1. Route Catalog Page
Figure 2. Route RAIM Prediction Page
2. Highlight and enter depart time, depart date, enroute altitude, and enroute ground speed. Press ENTER to
accept.
NOTE
You may also enter the satellite ID number in the field for any satellite (1-32)ā€˜rem satā€™
which has been notamed as ā€œout of serviceā€ during the flight, to exclude that particular
satellite from participating in predicting the Route RAIM availability. If nothing is entered
in the field, the unit assumes all satellites are usable.ā€˜rem satā€™
3. When all of the parameters are properly entered, the ā€˜Computeā€™ field will start flashing. Press . TheENTER
unit will start to predict the RAIM availability over the entire route, and the flashing field willā€˜Computeā€™
switch to ā€˜WAIT ->ā€™, with the arrow sign continually rotating, indicating that the prediction is in progress.
1
NOTE
The prediction function takes a certain amount of time, depending on the route distance
and the enroute speed (i.e., 1000 nautical miles = approximately 2 minutes). The longer
the route distance, the longer the time. The slower the enroute speed, the longer the time.
Also, if there is a RAIM unavailability detected based on the associated requirement, the
prediction process will stop immediately, and display as shown in Figure 3. ā€˜NO RAIMā€™
Figure 3. ā€˜NO RAIMā€™
4. If the entire route has RAIM availability, it will take a longer amount of time to complete, and display ā€˜RAIM
OKā€™ as shown in Figure 4.
NOTE
ā€˜NO RAIMā€™ does not mean RAIM is unavailable for the entire route. It is actually the out-
come of detecting the RAIM unavailability for more than 5 minutes over the intended
flight, based on the BRNAV requirements.
Figure 4. ā€˜RAIM OKā€™
2. ROUTE SETTINGS PAGE (pg. 87, Pilotā€™s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which removes the Route Settings
Page which allowed Automatic Leg Selection and Automatic Leg Sequencing to be enabled/disabled by the pilot.
3. APPROACH SELECT PAGE (pg. 66, Pilotā€™s Guide)
GARMIN GPS 155/165 software (all versions):
An ā€˜ā€˜unknā€ (unknown) approach type is displayed on the Approach Select Page when the unit software does not know
how to display a new approach type in the database. DO NOT USE THIS APPROACH TYPE.
2
4. CANCELLING PARALLEL OFFSET NAVIGATION (pg. 56, Pilotā€™s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which cancels parallel offset naviga-
tion when entering the 30 NM arrival approach circle (if an approach is present in the active route to allow approach to
arm). The change also allows indication of ā€œapproach not activeā€ if parallel navigation is re-instated after approach nav-
igation has been armed.
5. I/O CHANNEL 2 SETUP PAGE
Figure 5. I/O Setup Page
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which adds the I/O Channel 2 Setup
Page to the user-defined settings that are available. The I/O setup page lets you configure the GPS 155/165 to output to
an RS-232 mapping device or a PC (with the optional GARMIN PC Kit or other mapping software) and select the appro-
priate baud rate. The I/O setup page only provides access to I/O channel 2 input/output. For information on using I/O
channel 1, please see your GPS 155/165 installation manual. The input option for channel 2 is intended for future inter-
facing capabilities and is not a selectable option at this time.
To change the output settings for I/O channel 2:
1. Press
S
and rotate
O
until the I/O setup page is displayed.
2. Use
K
to select ā€˜offā€™ or ā€˜plottingā€™ for output to an RS-232 device.
3. Rotate
O
to advance the cursor to the baud rate field.
4. Use
K
to select the desired baud rate (300, 1200, 2400, 4800, 9600).
5. Press CRSR to finish.
6. SID SELECTION (pg. 79, Pilotā€™s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which allows the pilot to select a SID
from the nearest airport when the active route does not have a departure airport as the first waypoint.
7. OFF-ROUTE DIRECT-TO WAYPOINT (pg. 59, Pilotā€™s Guide)
The GARMIN GPS 155/165 software versions 3.07 and higher incorporate a change which retains a direct-to waypoint
as an off-route direct-to waypoint if a SID/STAR/Approach procedure waypoint is the active direct-to-waypoint when the
procedure is deleted and only the airport associated with the procedure remains in the active route.
3


Product specificaties

Merk: Garmin
Categorie: Navigator
Model: GPS 165

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin GPS 165 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Navigator Garmin

Handleiding Navigator

Nieuwste handleidingen voor Navigator