Futaba SBS-01V Handleiding

Futaba Afstandsbediening SBS-01V

Lees hieronder de 📖 handleiding in het Nederlandse voor Futaba SBS-01V (2 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

1M23N26714

SBS-01V

LED

toS.BUS2port

3PConnector

toEXTBattery

Fuse

（mount in either direction）

Heat Shrink Tube

Normal LineEXT Line

The example of wiring

to S.BUS2

port

to S.BUS2

port

R7008SB

Drivebattery1

（EXTBattery)

Receiverbattery

Drivebattery2

（EXTBattery)

Drivebattery1

（EXTBattery)

Drivebattery2

（EXTBattery)

Switch

Powersupplies

forservos

Another power

supply Hub

S.BUS2

servos

Twodrivebatteriesaremeasured(R7008SBuse)

Twodrivebatteriesandpowersuppliesforservosaremeasured(R7008SBuse)

●Batteryvoltagemeasurementforreceivers[R7008SBuse]

●Thedrivebattery1ismeasuredinanEXTport[R7008SBuse]

●Thedrivebattery2ismeasuredinanEXTline[SBS-01Vuse]

●Batteryvoltagemeasurementforreceivers[R7008SBuse]

●Thedrivebattery1ismeasuredinanEXTport[R7008SBuse]

●Thedrivebattery2ismeasuredinanEXTline[SBS-01Vuse]

●Thevoltageforservosismeasuredinapowersupplyline[SBS-01Vuse]

Normal Line

EXT Line

*SBS-01Vmeasurestwovoltage.Onecorrespondstohighvoltages,suchasadrivebattery,

withanEXTline.Anotherisanormallineandismeasurementofthebatteryforreceiversofa

lineconnectedto3Pconnector,orthebatteryforservos.

LED Indication

SBS-01V

Voltage sensor

Instruction Manual

Thank you for purchasing Futaba's

SBS-01V Voltage Sensor. This sensor,

used in conjunction with a telemetry

enabled transmitter/receiver, is used to

indicate the voltage of the item to which

it is attached. Although the telemetry

receiver of Futaba's has a function

which measures voltage, if SBS-01V

is used, it can measure more battery

voltage. To maximize your enjoyment,

and to ensure proper sensing, please

read through this manual thoroughly.

We also encourage you to retain the

manual for future reference should the

need arise.

●The SBS-01V is designed for use with

Futaba telemetry systems.

󾾝WARNING

Failure to follow these safety precautions may result in

severe injury to yourself and others.

󾾙To utilize the SBS-01V altitude sensor,

connect it to the S.BUS2 port of the Futaba

telemetry enabled receivers.　

■The SBS-01V will not function properly if connected to

an S.BUS port or other channel ports.

󾾙Ensure that the unit is connected properly

to the receiver. Failure to do so could result in

damage to the sensor.

󾾙Ensure that the unit is mounted in an area

that will eliminate exposure to fuel, water and

vibration.

■As with any electronic components, proper

precautions are urged to prolong the life and increase

the performance of the SBS-01V.

󾾙To ensure that the SBS-01V is functioning

as desired, please test accordingly.　

■Do not ﬂy until inspection is complete.

󾻭Do not use the SBS-01V with anything

other than an R/C model.

󾾙 In order to prevent any short circuits, please

observe the polarity of all connections.

■Ensure that the unit is connected properly; failure to

do so could result in damage to the cable, receiver, etc.

󾾙Always mount the cable in accordance with

the instructions included in this manual.

󾾙Allow a slight amount of slack in the cable.

■If necessary, fasten this cable at a suitable location to

prevent any damage from vibration during ﬂight.

󾻭Turn on the receiver prior to connecting the

Extra Voltage Input.

󾻭To prevent any short circuits, please ensure

that the cable is routed away from any condu-

cive materials.

󾻭Don't apply voltage higher than 100V to Ex-

tra voltage line.

■There is fear of explosion, ignition, and breakage.

󾾙It is cautious of the burn and ﬁre in wiring

work enough.

󾻭T -he work of wiring must not connect a bat

tery.

Green Normal operation

Red No signal reception

Green/Red When setting up the

slot

Green/Red

Alternate blink Unrecoverable error

Features

Measures receiver battery voltage

and the voltage of a second battery or

power supply.

External Line Range : 0-100V's

Normal Line Range : 3.5-8.4V's

Weight : 0.2oz (6.0g)

Length : 34.25in (870mm)

Slot Number Setup

Battery connection

SBS-01V uses two continuous slots.

Please note that the proper default

start slot for this accessory is number

6. When setup-changing or adding,

it is the following numbers that are

made to a start slot.

1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,

18,19,20,21,22,24,25,26,27,28,29,30

Information on how to change the

slot assignment is included in the

transmitter's manual.

What is measured is total voltage

when the battery which you want

to measure has two or more cells.

One cell of a battery with many cells

cannot be measured. Don't carry out

connection wiring at one cell. If it

connects with one cell, there is fear

of ignition.

SBS-01V

cable

① Measure the cable and then cut it to the desired length.

②Cut approximately 30mm of the negative (-, black) line from the cable.

Solder the fuse inline on the negative wire and then reattach the section of wire

that was previously removed. The fuse should be attached as close to the

external power supply as possible.

③Place a piece of heat shrink tubing over the fuse, ensuring that it covers the

soldered areas. Shrink the tubing snug to the fuse and the wire using a heat gun.

④The cable should be connected as shown in the diagram below. The cable

gets connected to the wires that come off the ESC and connect to the battery.

⑤ The manual for the Telemetry system should be referred to after the setup is

complete; checking to make sure it functions as desired and that it provides the

correct voltage on the display.

The fuse should be attached as close to the

external power supply as possible.

Heat shrink tube

Fuse to Black line (－)

Heat shrink tube

Heat shrink

The connection is aﬃxed to the ESC on the wires

that are connected to the battery by soldering them

and then protecting them with heat shrink.

To Power Battery

To Receiver S.BUS2 port

To Motor

Fuse（mount in either direction）

Fuse

Solder welding

motor

controller

The wiring processing method of an EXT Line

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

Product specificaties

Merk:	Futaba
Categorie:	Afstandsbediening
Model:	SBS-01V

Heb je hulp nodig?

Als je hulp nodig hebt met Futaba SBS-01V stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Afstandsbediening Futaba

Futaba SBS-01V Handleiding

10 December 2024

Futaba T3PV Handleiding

10 December 2024

Futaba DLPH-1 Handleiding

10 December 2024

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening

Audio-Technica AT-SL931HD Handleiding

6 December 2024

Velleman DVRRC4 Handleiding

3 December 2024

Vimar 14172 Handleiding

1 December 2024

Vimar 20172.120.B Handleiding

1 December 2024

Vimar 19172.B Handleiding

1 December 2024

Vimar R14516 Handleiding

1 December 2024

Vimar R19516.B Handleiding

1 December 2024

Vimar R19516 Handleiding

1 December 2024

Vimar R20516.N Handleiding

1 December 2024

Vimar R16956 Handleiding

1 December 2024