Fusion XS-SL10SPGW Handleiding

Fusion Subwoofer XS-SL10SPGW

Lees hieronder de 📖 handleiding in het Nederlandse voor Fusion XS-SL10SPGW (11 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/11
®
XS Series Subwoofer Installation Instructions .................................................................................. 2
Instructions d'installation du caisson de basse XS Series ................................................................ 6
Subwoofer XS Series Istruzioni di installazione .............................................................................. 10
Subwoofer der XS Series – Installationsanweisungen ................................................................... 14
Instrucciones de instalación del subwoofer de la XS Series ...........................................................18
XS Series da série esportiva da marca ...........................................................................................22
XS Series subwooferinstallatie-instructies ...................................................................................... 26
Garmin®, the Garmin logo, FUSION®, the Fusion logo, and True-Marine™ are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used
without the express permission of Garmin.
October 2018
190-02481-91_0A
XS Series Subwoofer Installation
Instructions
Important Safety Information
WARNING
Failure to follow these warnings and cautions could result in
personal injury, damage to the vehicle or vessel, or poor product
performance.
See the guide in the Important Safety and Product Information
product box for product warnings and other important
information.
This device must be installed according to these instructions.
Disconnect the vehicle's or vessel's power supply before
beginning to install this product.
CAUTION
Continuous exposure to sound pressure levels over 100 dBA
may cause permanent hearing loss. The volume is typically too
loud if you cannot hear people speaking around you. Limit the
amount of time you listen at high volume. If you experience
ringing in your ears or muffled speech, stop listening and have
your hearing checked.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
It is strongly recommended that you have your audio system
installed by a professional installer to ensure optimum
performance.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation, go
to for product support.www.fusionentertainment.com
After installing the subwoofer, you should run the subwoofer at
low to medium volumes for the first few hours of use. This helps
to improve the overall sound by gradually loosening up the
moving components of the subwoofer, such as the cone, spider,
and surround
What's In the Box
• 1 subwoofer
• 6 Phillips stainless steel, 4.8 mm x 50 mm (10 gauge x 2 in.)
mounting screws
• Mounting template
• Grilles
Tools Needed
• Electric drill
• Drill bit (size varies based on surface material)
• Phillips screwdriver
• Wire strippers
• Crimping tool
• Electrical tape
• Appropriate saw or utility knife to cut surface material
• Marine sealant (optional)
• Suitable gauge speaker wire for the length required
NOTE: For customized installations, additional tools and
materials may be needed.
Mounting Considerations
Selecting the correct mounting location is critical to optimize the
performance of the audio system. This FUSION® subwoofer is
designed to perform in the widest possible range of mounting
locations, but the more you plan the installation, the better the
subwoofer sound will be.
• The audio system must be turned off before making any
connections. Failure to do so could result in permanent
damage to the audio system.
• You should protect all terminals and connections from
grounding and from each other. Failure to do so could result
in permanent damage to the audio system and voids the
product warranty.
• You should protect the wires from sharp objects and always
use rubber grommets when wiring through panels.
• The mounting location must avoid potential obstacles, such
as fuel and hydraulic lines and wiring.
• The mounting location must provide sufficient clearance for
the mounting depth of the subwoofer as specified in the side
view drawings and the specifications.
• When possible, the area behind each subwoofer should be
enclosed.
• To avoid interference with a magnetic compass, the
subwoofer should not be installed closer to a compass than
the compass-safe distance value listed in the product
specifications.
• You should select a flat mounting surface for the best seal.
• For better bass performance, the subwoofer should be
mounted in an area that provides just enough room behind
the subwoofer. Too small an area restricts bass, and too
large an area compromises bass performance. Refer to the
specifications for optimum volume recommendations.
• When a subwoofer is not exposed to the outside
environment, a better bass performance can be achieved
using an enclosure that has a ported design.Theile Small
parameters are provided in the specifications to assist with
enclosure and port design.
• If you intend to mount the subwoofer outside the boat, follow
these considerations.
◦ When mounted correctly, the subwoofer is rated IP65 for
protection in the marine environment from the front of the
subwoofer. Water exposure and damage to the rear of the
subwoofer voids the warranty.
◦ The subwoofer must be mounted in a location well above
the waterline, where it is not submerged.
◦ The subwoofer must be mounted in a location where it
cannot be damaged by docks, pilings, or other pieces of
equipment.
◦ The subwoofer should be mounted in a sealed enclosure,
especially if it is exposed to wash down. A port or vent
may allow water to collect in the enclosure and damage
the subwoofer.
Mounting the Subwoofer
Before mounting the subwoofer, you must choose a location
following the mounting considerations above.
Before cutting the mounting surface, you should verify that there
is enough clearance for the speaker behind the surface. Refer to
the specifications for clearance information.
NOTICE
Do not apply grease or lubricant to the screws when fastening
the subwoofer to the mounting surface. Grease or other
lubricants can cause damage to the subwoofer housing.
1Route the wires from the source to the mounting location,
away from sources of electrical interference.
2Trim the template and make sure it fits in the selected
location.
3Orient the template so the FUSION logo is level in the
selected location.
2 Installation Instructions
4Secure the template to the selected location.
5Using a rotary tool or jigsaw, cut the mounting surface along
the inside of the line on the template.
6Place the subwoofer in the cutout to test the fit.
7If necessary, use a file and sandpaper to refine the size of
the cutout.
8After the subwoofer fits correctly in the cutout, ensure the
mounting holes on the subwoofer line up with the pilot holes
on the template.
9If the mounting holes on the subwoofer do not line up, mark
the new hole locations.
10 Using an appropriately sized drill bit for the mounting surface
and screw type, drill the holes.
11 Remove the template from the mounting surface.
12 Connect the subwoofer wires À while observing polarity
( ).Subwoofer Wiring, page 3
13 If necessary, connect the LED wires to the Sports model
subwoofer ( ).LED Wiring, page 3
14 Place the subwoofer in the cutout.
15 Secure the subwoofer to the mounting surface using the
included screws Á.
NOTE: Do not over tighten the screws, especially if the
mounting surface is not flat.
16 With the subwoofer mounted, hold the grille with the FUSION
logo at the bottom, or at the 6 o'clock position.
17 Press on the grille to snap it into place.
Subwoofer Wiring
When connecting the subwoofer to your amplifier or source,
observe the following considerations.
• Speaker wire is not included with the subwoofer. You should
use 20 AWG (0.52 mm2) speaker wire to connect the
subwoofer to the amplifier or source.
• The leads on the subwoofer are terminated using male spade
connectors. You should use female spade connectors (not
included) to connect the speaker wire to the speaker leads
for the best connection.
• The subwoofer features a dual 2 Ohm voice coil that can be
configured for 2.1 operation (two speakers and one
subwoofer) when connected to a FUSION stereo with DSP
capability (Configuring the Subwoofer for 2.1 Operation,
page 4).
• You can use the following table to identify the polarity of the
leads on the speaker.
White Positive (+)
Gray with a black stripe Negative (-)
NOTE: Gray and white with a black stripe wires are
connected to jumper terminals on the back of the subwoofer.
These wires must remain connected to the jumper terminals
for normal use (4 Ohm) and should be disconnected only
when configuring the speaker for 2.1 operation.
LED Wiring
Connecting the LED Wires
You can control the color of the LEDs by connecting the LED
color wires to ground. You can splice the ground wire to multiple
LED wires to customize the LED color.
NOTE: This feature is available only on the sports model.
NOTE: Instead of connecting the LED wires for one dedicated
color, you can install a remote control to turn the LEDs on and
off, change the color, and create lighting effects. See your
FUSION dealer or for more www.fusionentertainment.com
information.
The black wire on the LED cable is terminated with a 4 mm
female bullet connector, and the color wires are terminated with
4 mm male bullet connectors. You can connect these to 4 mm
bullet connectors on your wires (not included), or remove the
bullet connectors to connect to the bare wires instead.
1Connect a positive wire to the black wire on the LED cable.
2Connect a ground wire to the wire on the LED cable
according to the preferred LED color.
LED Color LED Wire Color
Red Red
Green Green
Blue Blue
Yellow Red and green
Magenta Red and blue
Cyan Blue and green
White Red, green, and blue
3Route the positive and negative wires, and connect them to a
power source (Connecting the LED Wires to Power,
page 3).
Connecting the LED Wires to Power
NOTE: This feature is available on only the sports model.
You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at
the power-source end of the cable. You should connect the
positive (+) power wire to a 12 Vdc power source through an
isolator switch or circuit breaker to turn the LEDs on and off. You
can use the same isolator or circuit breaker controlling the
power supply to your stereo, which allows you to turn the LEDs
and the stereo on and off at the same time.
You should use 22 AWG (0.33 mm2) or thicker wire to connect
the LEDs to the battery.
1Route the positive power (+) and negative ground (-) wires
from the LED-wire connections to the battery.
2Connect the negative wire to the negative (-) battery terminal.
3Connect the positive wire to the positive (+) terminal through
a 3 A fuse and isolator switch or circuit breaker.
Subwoofer Sound Optimization
While installing the subwoofer, you can ensure the sound from
the subwoofer is optimized by running the subwoofer out of
phase. You can switch the positive and negative wires on the
amplifier or source to run them out of phase.
Running the subwoofer out of phase from the speakers allows
you to hear if the perception of bass is more from the location of
the subwoofer or from the speakers. If running the subwoofer
out of phase gives a better perception that the bass is from the
speakers’ location, then out-of-phase wiring is correct for your
system.
You can run the subwoofer out of phase by temporarily
switching the positive and negative connections from the
subwoofer at the amplifier or source. Depending on the outcome
of the test, you can then switch the connections back if
necessary.
Installation Instructions 3

Product specificaties

Merk: Fusion
Categorie: Subwoofer
Model: XS-SL10SPGW

Heb je hulp nodig?

Als je hulp nodig hebt met Fusion XS-SL10SPGW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer Fusion

Fusion

Fusion CS-AT1100 Handleiding

9 Juli 2023
Fusion

Fusion XS-SL10SPGW Handleiding

27 Juni 2023
Fusion

Fusion SG-SL122SPC Handleiding

19 Juni 2023
Fusion

Fusion XS-S10SPGW Handleiding

18 Juni 2023
Fusion

Fusion SG-SL102SPC Handleiding

16 Juni 2023
Fusion

Fusion FM-S10SW Handleiding

12 Juni 2023
Fusion

Fusion SG-S102W Handleiding

11 Juni 2023
Fusion

Fusion MS-SW10 Handleiding

10 Juni 2023
Fusion

Fusion XS-S10CWB Handleiding

9 Juni 2023
Fusion

Fusion SG-SL122SPW Handleiding

9 Juni 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

Deaf Bonce

Deaf Bonce Apocalypse ASA-4000.1 Handleiding

20 November 2024
Deaf Bonce

Deaf Bonce Apocalypse Atom 2000 PRO Handleiding

20 November 2024
JBL

JBL PSW-D115 Handleiding

20 November 2024
JBL

JBL PSW-D110 Handleiding

20 November 2024
JBL

JBL PSW-D112 Handleiding

20 November 2024
JBL

JBL Power P1224 Handleiding

20 November 2024
JBL

JBL Power P1220D II Handleiding

20 November 2024
JBL

JBL Power P1242 Handleiding

20 November 2024
JBL

JBL Power P1220 II Handleiding

20 November 2024
JBL

JBL Power P1020 II Handleiding

20 November 2024