Fusion CP-AS1080 Handleiding

Fusion Autospeaker CP-AS1080

Lees hieronder de 📖 handleiding in het Nederlandse voor Fusion CP-AS1080 (2 pagina's) in de categorie Autospeaker. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

8” SUPER SLIM ACTIVE SUBWOOFER

SPECIFICATIONS

CP-AS1080

Peak Power (Watts) 300

Rated Power (Watts) 100

Frequency Response 20Hz - 120Hz

Dimensions (mm) 330(l) x 245(w) x 78(h)

13 x 9-5/8 x 3”

CP-AS1080

www.fusionelectronics.com

INSTALLATION GUIDELINES

1. Ensure the +12V lead is disconnected from the battery before you connect any new equipment.

2. Ensure the mounting location will not interfere with the gas tank, brake lines or electrical wiring.

3. Ensure the Super Slim Active Subwoofer is securely fastened to the vehicle to prevent damage in the event of an accident.

4. Ensure all wiring is protected to avoid pinching or crushing which could result in damage to the audio system.

5. Ensure the mounting location has sufﬁcient air ﬂow around the ampliﬁer.

6. Ensure you use the recommended gauge wire/cable for all ampliﬁer connections.

WIRING

Ensure the audio system is turned off before making any connections

to the ampliﬁer, speakers or source unit.

Failure to do so could result in permanent damage to the audio

system. When wiring the FUSION Super Slim Active Subwoofer

ensure that the cable is protected from sharp objects and always

use rubber grommets when wiring through metal panels.

Ensure all terminals and connections are protected from the vehicle

chassis, and from each other, as failure to do so could result in

permanent damage to the audio system.

FUSION Electronics recommends 8 gauge wire (power & ground).

GROUND

When grounding/earthing your Super Slim Active Subwoofer

ensure that the location is a good source of ground (preferably the

ﬂoor pan). Make sure the metal is clean of paint etc as a poor earth

could damage your audio system.

Note: This is the ﬁrst connection to be made!!

REMOTE TURN ON

This connection turns the ampliﬁer on and should be connected to

the remote turn on wire from the Head Unit. If one is not available

a switched 12V source must be used. Either a power antenna wire

or ACC +12V.

POWER

Connect the power lead directly to the +12V battery terminal with

an inline fuse or circuit breaker as close to the battery as possible.

LOW LEVEL INPUTS

Choose the correct length RCA interconnects and run them to the

RCA outputs of the source/head unit, avoiding running beside other

looms and or power cable.

Note: For correct performance both input RCA connectors must

be used.

HIGH LEVEL INPUTS (SPEAKER LEVEL)

If your head unit does not have RCA outputs, you can use the

speaker outputs for the audio source for the CP-AS1080. Use the

supplied cable and wire harness and connect the speaker outputs

from the source to the high level Input. Be sure to observe polarity

to avoid audio phase problems.

Note: When using the high level connection, the Level MUST be set

to minimum or the Subwoofer will be permanently damaged and

could void your warranty.

LOW LEVEL OUTPUTS

Use the RCA output connectors to make one CP-AS1080 linkable

to multiple CP-AS1080 Super Slim Active Subwoofers. This output

is a pass-thru connection derived from the RCA input connector so

the signal level and frequency response is the same as the original

input signal.

YOU CAN HELP PROTECT THE ENVIRONMENT! Please remember to respect the local regulations: Hand in the non-working electrical equipment to an appropriate waste disposal center.

RECORD YOUR PURCHASE DETAILS HERE:

SERIAL NUMBER

DATE OF PURCHASE

AFFIX RECEIPT HERE

WARNING: Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may cause permanent

hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE!

TROUBLE SHOOTING

Problem Possible Reason Solution

Not switching on.. • No +12V to power wire • Check fuses and connections to battery

Power LED not ‘on’. • No power to remote wire • Check remote on connections to head unit

• Fuse broken • Replace fuse with correct type and amperage

Not working, but status • Fuse blown • Replace fuse with correct type and amperage

LED is ‘on’ • Ampliﬁer too hot • Move ampliﬁer to vented area

• Turn head unit down

No Sound • RCA Signal • Check RCA connection to head unit

• Gain control not set up • Ensure you have set up the ampliﬁer gain level control

• Head Unit • Check head unit volume level

• Connections • Check all power, remote on and ground connections

For further product and installation information, please visit www.fusionelectronics.com

Pour plus d’informations sur les produits et l’installation, rendez-vous sur www.fusionelectronics.com

Para obtener más información acerca de los productos y de su instalación, visite el sitio web www.fusionelectronics.com

Bezoek www.fusionelectronics.com voor meer product- en installatie-informatie.

Weitere Produkt- und Installationsinformationen ﬁnden Sie unter www.fusionelectronics.com

Per ulteriori informazioni sui prodotti e la loro installazione, potete visitare www.fusionelectronics.com

Для получения дополнительной информации о продуктах и установке зайдите, пожалуйста, на: www.fusionelectronics.com

LEVEL CONTROL

This control is used to match the input level of the ampliﬁer to

the output level of your head unit. We recommend the following

method.

1. Turn the ampliﬁer level to zero

2. Turn the volume of the head unit to ¾ & the bass & treble to zero

3. Adjust the level control until the desired maximum volume is

achieved without distortion

4. Failure to follow these steps may cause permanent damage to

the audio system

LOW PASS FILTER

Ensure the crossover frequency is set at 120Hz or below. This

feature is designed to ﬁlter out all mid to high frequencies that only

full range speakers should produce

BASS BOOST

Set the bass boost level to increase the bass at 45Hz. Selectable

from 0dB - 12dB gains

REMOTE CONTROL LEVEL INPUT

Attach the remote level control (via the included cable) to control

the volume level of the subwoofer independently at the front of the

vehicle.

PHASE SHIFT (0-180 DEG)

Use this switch to help compensate for time alignment problems

in the system. Such problems usually result from having the

subwoofer at a different distance from the listener than the other

speakers in the system.

Product specificaties

Merk:	Fusion
Categorie:	Autospeaker
Model:	CP-AS1080
Breedte:	256 mm
Diepte:	330 mm
Hoogte:	78 mm
Gemiddeld vermogen subwoofer:	- W
Aantal drivers:	1
Diameter driver subwoofer (imperiaal):	8 "
Type behuizing:	Bijgevoegd
Subwoofertype:	Actieve subwoofer
Frequentiebereik subwoofer:	20 - 120 Hz
Type product:	Tevoren geladen subwoofer
Subwoofer maximale vermogen:	600 W