Frigidaire PL30DD50EC Handleiding

Frigidaire Ventilator PL30DD50EC

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire PL30DD50EC (10 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

MODELS PL30DD & PL36DD

DOWNDRAFT BLOWER SYSTEM

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code au-

thorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Do not use this range hood with an additional speed control

device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Do not install this product with the activating switch directly

behind a burner or element. Minimum distance between the

switch and the edge of the burner should be 4 inches.

10. Loose-fitting or hanging clothing should never be worn when

operating this appliance. They may be ignited by burners/

elements on cooktop.

11. Children should not be left alone or unattended in the area

where this appliance is in use.

12. When flaming foods, turn the blower OFF. An operating blower

may spread the flames.

13. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat

oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when

cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWINGa:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet,

or metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out immedi

ately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels

- a violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher, and you

already know how to operate it.

B. The fire is small and contained in the area where it

started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

a Based on “Kitchen Firesafety Tips” published by NFPA.

INSTALLER: Save this manual for Electrical Inspector and Homeowner to use.

HOMEOWNER: Use and Care Information on Page 5.

AIR

VENT

COUNTER

TOP

BLOWER

BOX

CHIMNEY TOP

3-1/4" X 10"

DUCT CONNECTOR

COOK TOP

GEAR

MOTOR

COVER

TYPICAL INSTALLATION

120 VAC

GROUNDED

OUTLET

PLANNING

This downdraft blower system is

designed to be used to exhaust

airborne contaminants when

cooking with a variety of gas or

electric cooktops. It can be

mounted in island, peninsula, or

conventional wall locations.

This unit can be easily installed

following these basic steps:

•Cut out the countertop

opening.

•Mount the unit in the

cabinet.

•Connect the ductwork

and electrical.

•Install the cooktop.

INTENDED FOR DOMESTIC COOKING ONLY

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. Clean filters and grease-laden surfaces frequently.

4. Do not repair or replace any part of this appliance unless

specifically recommended in this manual. All other servicing

should be done by a qualified technician.

5. Please read specification label on product for further informa-

tion and requirements.

PLANNING - (continued)

RIGHT

DISCHARGE

DOWN

DISCHARGE

(as shipped)

LEFT

DISCHARGE

EQUALS 6 FT. OF

STRAIGHT DUCT

6" ROUND

ELBOW

3-1/4" X 10"

TO 6" RD.

TRANSITION

3-1/4" X 10"

90O ELBOW

EQUALS 8

FT. OF

STRAIGHT DUCT

EQUALS 2

FT. OF

STRAIGHT DUCT

Pay special attention to the areas of potential interference high-

lighted above. A countertop with (A) a raised lip and/or (B) a

backsplash may not allow enough flat countertop for a proper

installation. Note that 2" of flat countertop is required behind

cooktop and that 1-3/4" is necessary between the back edge of the

cooktop and the inside of cabinet back.

SPECIFICATIONS

VOLTS AMPS CFM DUCT

120 4.0 500 3-1/4 X 10

TAKE MEASUREMENTS

1. Refer to the cooktop installation instructions for dimensions of

cooktop, countertop cut-out, and cabinet requirements. The

Model PL30DD will fit in most 30" wide cabinets and the Model

PL36DD will fit in most 36" wide cabinets. However, it is

recommended that oversized cabinets be used for easier instal-

lation.

2. Cooktop depth can vary greatly from one to another. This may

cause the fit of these two appliances to be rather tight.

Note: The high level of air flow of this appliance may affect the gas

flame on some types of gas cooktops. This is NORMAL and will

cause no harm, but can be corrected by lowering the speed of the

blower.

PLAN THE DUCTWORK

1. This downdraft blower system is designed for use with 3-1/4"

x 10" ductwork (can be transitioned to 6" round). Three

different discharge directions are available with side-to-side

adjustment for accurate alignment of ductwork.

2. For best performance: Choose the ducting option which allows

the shortest length of ductwork and a minimum number of

elbows and transitions. Check location of floor joists, wall

studs, electrical wiring or plumbing for possible interference.

NOTE: The unit is shipped with the 3-1/4" x 10" discharge

facing DOWN. See “CHANGING BLOWER DIRECTION” on

page 3, if necessary.

3. The system will operate most efficiently when the ductwork

does not exceed 40 feet of equivalent duct. The chart, above,

shows equivalent feet of elbows and transitions. The number

of feet of straight duct plus the equivalent feet of transitions

and/or elbows to be used should equal 40 feet or less.

NOTE: The equivalent feet of various roof and wall caps has

been taken into consideration. Do not include them in this

calculation.

PLAN THE WIRING

1. The downdraft blower system draws 4 AMPS and requires a

120 VAC, 60 Hz circuit.

2. The unit has a 2 ft. long power cord with a 3-pronged plug. Plan

to provide a grounded outlet in a location which will allow the

unit’s power cord to reach. (Note: If the Model PL30DD is being

installed in a 30" wide cabinet or the Model PL36DD is being

installed in a 36" wide cabinet, the outlet cannot be located on

the back wall of cabinet.) Outlet may also be wall-mounted,

with access hole in cabinet.

LEVELING BRACKET -

FLANGE FACING IN

LEVELING BRACKET -

FLANGE FACING OUT

MOUNTING SCREWS

COVER PLATE

CLAMP

CHANNEL

NUT

BLOWER

MOTOR

PLUG

SHEET

METAL

SCREW

CLAMP

CHANNEL

NUTS

SHEET

METAL

SCREW

BOTTOM

FLANGE

BLOWER

PREPARATION

CHANGING BLOWER DISCHARGE (Optional)

The blower is shipped with its discharge facing DOWN. Follow

these steps ONLY if:

•the position of the blower discharge needs to be moved

so ductwork does not interfere with floor joists, plumb

ing or wiring below.

•it is necessary to rotate the blower discharge to the

RIGHT or LEFT.

Place the unit on its back on a table or work surface.

DOWN DISCHARGE - MOVING BLOWER LEFT OR RIGHT

1. Loosen the 4 nuts and 2 clamp channels.

2. Slide blower to desired position.

3. Use supplied cover plate to close open space (if any).

4. Tighten wing nuts to secure top of blower and use sheet metal

screws through bottom flange to secure bottom of blower.

1. Remove the 4 nuts and 2 clamp channels.

2. Carefully lift blower and disconnect motor plug if necessary.

Reposition blower and RECONNECT MOTOR PLUG.

3. Use supplied cover plate to close open space (if any).

4. Replace clamp channels and use nuts to secure the blower in

its new position.

5. Use sheet metal screws through bottom flange to secure

bottom of blower.

CUT COUNTERTOP OPENING

1. Lay out and cut the cooktop cut-out far enough FORWARD so

downdraft will fit behind it.

2. Set cooktop in place and slide it as far forward as possible.

Center and square it with edges of countertop.

3. Place the plastic template against the back flange of the

cooktop and center it. Trace around template to mark the

downdraft opening.

4. Remove cooktop from countertop.

5. Cut downdraft opening. Be careful not to chip edges of

countertop.

MOUNT THE UNIT

1. Set downdraft into opening. Extend leveling brackets to floor

of cabinet so downdraft sits straight. (Note: Leveling brackets

can be removed and re-attached in other positions. Bottom

flange may have to face inward in tight cabinet installations.)

2. Secure the downdraft to the countertop as follows: Hold the

downdraft against the back of countertop cut-out and tighten-

ing the 2 mounting screws (one on each end of unit) on

underside of countertop. Use a wood shim between screw and

underside of granite countertops.

3. Screw leveling brackets to bottom of cabinet. Tighten screws

holding leveling bracket to unit on each side.

LEFT OR RIGHT DISCHARGE

Product specificaties

Merk:	Frigidaire
Categorie:	Ventilator
Model:	PL30DD50EC

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire PL30DD50EC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ventilator Frigidaire

Frigidaire FCVW3062AS Handleiding

26 December 2023

Frigidaire FCVW3062AD Handleiding

26 December 2023

Frigidaire F36WC19EC Handleiding

4 Juni 2023

Frigidaire PLHV36W7CC Handleiding

18 Mei 2023

Frigidaire UCVH2001AS Handleiding

14 Mei 2023

Frigidaire F30WV16EC Handleiding

2 Mei 2023

Frigidaire PLHV36W6CC Handleiding

29 April 2023

Frigidaire PLHV42P8CC Handleiding

25 April 2023

Frigidaire F30WV16EB Handleiding

24 April 2023

Frigidaire F30WR01ES Handleiding

16 April 2023

Handleiding Ventilator

Nieuwste handleidingen voor Ventilator

Svan SVP401600MOBA Handleiding

20 December 2024

Svan SVP401600OBA Handleiding

20 December 2024

Livoo DOM510 Handleiding

20 December 2024

Orava SF-13 Handleiding

18 December 2024

EMOS P56PR2 Handleiding

14 December 2024

Midea FTS30-13AR Handleiding

14 December 2024

Midea FTS35-9AR Handleiding

14 December 2024

Midea FTS30-9AR Handleiding

14 December 2024

Aspes AVT453100ON Handleiding

13 December 2024

Aspes AVP401600OVBA Handleiding

13 December 2024