Frigidaire F30WV16EC Handleiding

Frigidaire Ventilator F30WV16EC

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire F30WV16EC (8 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac-

turer. If you have questions, contact the manufacturer at the

address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a quali-

fied person(s) in accordance with all applicable codes and

standards, including fire-rated construction codes and stan-

dards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authori-

ties.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this

range hood with an additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Use with approved cord-connection kit only.

10. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ig-

nite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when

cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be al-

lowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for

the size of the surface element.

F30WV SERIES

HOODS

F24WR & F30WR

SERIES HOODS

ECONOMY RANGE HOOD

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO PRE-

VENT BURNS. If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - a

violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you al-

ready know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. For best capture of cooking impurities, your range hood should

be mounted 18-24" above the cooking surface.

4. Please read specification label on product for further information

and requirements.

INSTALLER: Leave This Manual With Homeowner.

HOMEOWNER: Use and Care Information on Page 5.

WARNING

INTENDED FOR DOMESTIC COOKING ONLY

6" ROUND

DUCT

WALL CAP

3-1/4" X 10" DUCT

ROOF CAP

3-1/4" X 10" DUCT

ADJUSTABLE ELBOW

WALL CAP

TOOLS AND

MATERIALS REQUIRED

❏Drill, electric or ratchet drive

❏1/8" Drill bit for drilling pilot holes

❏1-1/4" wood bit for drilling electrical wiring access hole

❏One straight blade and one phillips head screwdriver

❏Pliers

❏Pencil and ruler and/or tape measure

❏Saber saw or keyhole saw for cutting 1" x 2" wood strips to

length and cutting wall or cabinet openings

❏Caulking, metal snips, duct tape, duct (with elbows and tran-

sition, if necessary) and roof or wall cap, as required

❏Electrical wiring and supplies of type to comply with local

codes

The following materials are required only for installations on

recessed bottom kitchen cabinets:r Ducted

❏Two 1" x 2" x 12" (approximate length) wood strips (pur-

chase locally)

❏Four 1-1/4" long flat head wood screws (purchase locally)

PLANNING DUCTWORK

INSTALLATION

(This section for F30WV hoods only. F30WR and F24WR

hoods skip this section and go on to “Prepare the Hood”. )

Begin planning ductwork by deciding where the duct will run

between the range hood and the outside. For best performance,

use the shortest possible duct run and a minimum number of

elbows. There are several choices shown - FIGS. A - F below.

FIG. A. Ducting directly through the wall (for range hoods

mounted on an exterior wall). Shown are two ways to duct

through an outside wall. If a wall cap is used directly off the

back of the hood, special care must be taken to make sure that

the damper in the damper/duct connector on the hood and

damper in the wall cap do not interfere with each other when

the hood is operating. This could result in either inadequate air

delivery or backdrafts. If this condition does exist, remove the

hood damper flap. Sometimes when using a wall cap it is easier

to duct vertically and then use an elbow as shown in FIG. B.

In more complex ducting situations, a 3-1/4" x 10" rec-

tangular ducting range hood (F30WV hood) can be converted

to a round duct by means of a transition.

FIG. C. Ducting straight up through the roof using

3-1/4" x 10" rectangular duct (for single story installations -

F30WV hood only).

FIG. D. Ducting between the ceiling joists (for multi-story instal-

lations) or through the soffit space above the cabinets (where

the soffit connects to an outside wall).

FIG. E. Straight up through the roof using 6" round duct (for

single-story installations).

FIG. B

FIG. C

FIG. D

FIG. A

3-1/4" X 10" TO 6"

ROUND DUCT

TRANSITION

FIG. E

6" ROUND

DUCT

ROOF CAP

3-1/4"

10" TO 6"

ROUND DUCT

TRANSITION

DAMPER/DUCT CONNECTOR (F30WV HOOD ONLY)

HINGE

PINS

DUCT

KNOCKOUTS

PREPARE THE HOOD

1. Unpack hood and check contents. You should receive:

1 -Aluminum Filter (F30WV hood only)

1 -3-1/4" x 10" Damper/Duct Connector (mounted

inside of hood for shipping only) (F30WV

hood only)

1 - Ductree filter (F24WR and F30WR hoods only)

2. Remove wiring box cover. Under cover find:

1 -Plastic Bag containing loose mounting hard-

ware

3. Remove top or rear electrical knockout. (FIG. 2)

4. (F30WV hood ONLY) Remove duct knockout. Insert screw-

driver under edge of knockout, break tabs, and peel knock-

out back with pliers. (FIG. 3)

5. (F30WV hood ONLY) Install damper/duct connector over

opening made in STEP 4. Use #8B sheet metal screws pro-

vided. (FIG. 3)

FIG. 1

FIG. 2

FIG. 3

FIG. 4

WIRING BOX COVER

DUCTFREE

FILTER

(F24WR &

F30WR

HOOD

ONLY

)

ALUMINUM

FILTER

(F30WV

HOOD

ONLY)

KEYHOLE

SLOTS

PREPARE THE

INSTALLATION LOCATION

Omit STEP 1 if hood will be installed under cabinets with flush

bottom.

1. (For installation on recessed bottom cabinets only) Attach a

wood filler strip at each side of recessed area under cabi-

net. Use two 1" x 2" strips cut to length. If recess is deeper

than 1" use thicker strips. Attach strips with 1-1/4" wood

screws, 3" from each end of strip. See FIG. 4.

2. Measure and mark the following (FIGS. 5A & 5B):

a.) Electrical wiring opening in wall or cabinet.

b.) Duct opening in wall or cabinet (F30WV hood ONLY).

WARNING

WHEN CUTTING OR DRILLING INTO WALL OR CABINET,

BE CAREFUL NOT TO CUT EXISTING ELECTRICAL

WIRING.

3. Use 1-1/4" bit to drill opening for electric wiring.

4. Cut out duct opening in wall or cabinet with saber saw or

keyhole saw.

5. Center hood in installation opening and trace keyhole slots

onto wood filler strips on cabinet bottom.

6. Screw four #10 x 7/8 wood screws into exact center of narrow

end of traced keyhole slots. Allow 3/8" of screws to project, so

that hood can be fitted into place later.

ELECTRICAL

KNOCKOUTS

Product specificaties

Merk:	Frigidaire
Categorie:	Ventilator
Model:	F30WV16EC

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire F30WV16EC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ventilator Frigidaire

Frigidaire FCVW3062AS Handleiding

26 December 2023

Frigidaire FCVW3062AD Handleiding

26 December 2023

Frigidaire F36WC19EC Handleiding

4 Juni 2023

Frigidaire PLHV36W7CC Handleiding

18 Mei 2023

Frigidaire UCVH2001AS Handleiding

14 Mei 2023

Frigidaire F30WV16EC Handleiding

2 Mei 2023

Frigidaire PLHV36W6CC Handleiding

29 April 2023

Frigidaire PLHV42P8CC Handleiding

25 April 2023

Frigidaire F30WV16EB Handleiding

24 April 2023

Frigidaire F30WR01ES Handleiding

16 April 2023

Handleiding Ventilator

Nieuwste handleidingen voor Ventilator

Aerian MISTY100 Handleiding

17 November 2024

Tornado HI-FAN-24HVWM-1P Handleiding

17 November 2024

Tornado HI-FAN-24PF-1P Handleiding

17 November 2024

Tornado HI-FAN-24MOWF-A-1P Handleiding

17 November 2024

Tornado HI-FAN-20HVWM-A-1P Handleiding

17 November 2024

Tornado HI-FAN-20WMPRO-1P Handleiding

17 November 2024

Tornado HI-FAN-24MOWF-WR-1P Handleiding

17 November 2024

Tornado HI-FAN-30HVOF-1P Handleiding

17 November 2024

Tornado HI-FAN-30POF-WR-1P Handleiding

17 November 2024

Tornado HI-FAN-20POF-5BA-1P Handleiding

17 November 2024