Frigidaire IMKFD23A Handleiding

Frigidaire Niet gecategoriseerd IMKFD23A

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire IMKFD23A (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 178 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
P/N A23057901 210927
B. Ice Maker (x1) C. Ice Bucket (x1)
E. Shoulder Screws (x2) F. Screw (x1)
Cobra FRZ IM Numbers:
• CD: IMKFD23A
• SD: IMKFD28A
AUTOMATIC ICE MAKER
INSTALLATION INSTRUCTIONS
An authorized service technician is recommended to install the Ice Maker Kit.
Tools Needed:
• Phillips Screwdriver
• Flat-head Screwdriver
• ¼-inch Socket Wrench or Nut Driver
• Adjustable Wrench
Kit Components
P/N A23057901 210927
2. Use Phillips screwdriver to install two shoulder
screws (E) in the upper rear holes. Turn until
shoulder screws are in firm contact with freezer
wall. (See Figure 1).
7. Insert and tighten screw (F) in outermost hole on
bracket to fasten it to the upper side of freezer
wall. (See Figure 3).
Figure 1
Figure 3
Figure 2
8. Follow steps in Use & Care Manual to reinstall
door and add baskets.
9. Put Ice Bucket (C) on basket as shown in Figure 4.
Automatic Ice Maker Installation
1. Unplug refrigerator from electrical outlet.
NOTE
We recommend the freezer door and freezer
baskets be removed before proceeding with the
installation. Please refer to ‘Removing Freezer
Drawer’ in the “Removing the Doors” section and
‘Freezer Features’ in the “Storage Features” section
in the Use & Care Manual.
Figure 4
3. Remove the connector cover.
4. Plug the ice maker connector into the connector
in the freezer compartment.
5. Hang the ice maker and bracket assembly loosely
on the shoulder screws using the keyhole slots in
the bracket.
6. Push the Ice Maker and bracket assembly toward
the rear of the freezer compartment to seat the
keyhole slots firmly onto the shoulder screws (See
Figure 2).
NOTE
Verify the switch is in the ON position.
E
F
E
Connector Cover
C
Switch
E
E
Connector
P/N A23057901 210927
Before Installing The Water Supply Line, You Will
Need:
• Basic Tools: adjustable wrench, flat-head
screwdriver, and Phillips screwdriver
• Access to a household cold water line with water
pressure between 30 and 100 psi.
• A water supply line made of inch (6.4mm) OD, ¼
copper or stainless steel tubing. To determine the
length of tubing needed, measure the distance
from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the refrigerator
can be moved out for cleaning (as shown).
• A shuto valve to connect the water supply line to ff
your household water system. DO NOT use a self-
piercing type shutoff valve.
• Do not reuse compression fitting or use thread
seal tape.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to the ice
maker inlet valve.
NOTE
Check with your local building authority for
recommendations on water lines and associated
materials prior to installing your new refrigerator.
Depending on your local/state building codes,
Electrolux recommends for homes with existing
valves its Smart Choice® water line kit 5305513409
(with a 6 ft. Stainless Steel Water Line) and for
homes without an existing valve, Electrolux
recommends its Smart Choice Water® line kit
5304490717 (with a 20 ft. Copper Water Line with
self-tapping saddle valve). Please refer to
www.electrolux.com for more information.
Figure 1
Plastic Water
Tubing to Ice
Maker Fill
Tube
Steel
Clamp
Brass
Compression
Nut
Ferrule
(Sleeve)
Copper
water line
Water Valve
Bracket
Valve Inlet
Water Valve
Copper water line
from household
water supply
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
To Connect Water Supply Line To Ice Maker Inlet
Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket.
Turn ON water supply and flush supply line until
water is clear. Turn OFF water supply at shutoff valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass compression
nut, then ferrule (sleeve) onto water supply line.
Push water supply line into water valve inlet as far
as it will go ( inch/6.4 mm). Slide ferrule (sleeve) ¼
into valve inlet and finger tighten compression
nut onto valve. Tighten another half turn with a
wrench; DO NOT overtighten. See Figure 1.
IMPORTANT
Ensure that your water supply line connections
comply with all local plumbing codes.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing is
recommended for the water supply line. Water
supply tubing made of inch plastic is not ¼
recommended to be used. Plastic tubing greatly
increases the potential for water leaks, and the
manufacturer will not be responsible for any
damage if plastic tubing is used for the supply line.
• DO NOT install water supply tubing in areas
where temperatures fall below freezing.
• Chemicals from a malfunctioning softener
can damage the ice maker. If the ice maker is
connected to soft water, ensure that the softener
is maintained and working properly.
Connecting Ice Maker to Water Supply
WARNING
To avoid electric shock, which can cause death or
severe personal injury, disconnect the refrigerator
from electrical power before connecting a water
supply line to the refrigerator.

Product specificaties

Merk: Frigidaire
Categorie: Niet gecategoriseerd
Model: IMKFD23A

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire IMKFD23A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Frigidaire

Frigidaire

Frigidaire FDHP4336AS Handleiding

2 November 2024
Frigidaire

Frigidaire GDPH4525AF Handleiding

26 Juli 2024
Frigidaire

Frigidaire FDSR4501AP Handleiding

25 Maart 2024
Frigidaire

Frigidaire 11NBSTGSDS Handleiding

26 Juli 2023
Frigidaire

Frigidaire 11NBRRFLDS Handleiding

13 Juni 2023
Frigidaire

Frigidaire MWTK30K Handleiding

3 Juni 2023
Frigidaire

Frigidaire 11NBBKGDSS Handleiding

2 Juni 2023
Frigidaire

Frigidaire 11NBSTELDS Handleiding

2 Juni 2023
Frigidaire

Frigidaire MWBOK15TB Handleiding

30 Mei 2023
Frigidaire

Frigidaire FCRS181RQ Handleiding

21 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Senal

Senal SCS-98 Handleiding

21 November 2024
Senal

Senal ASM-6 Handleiding

21 November 2024
Senal

Senal ASM-MNTKIT Handleiding

21 November 2024
Senal

Senal SMS-45 Handleiding

21 November 2024
Smeg

Smeg KIT6PX Handleiding

21 November 2024
Senal

Senal SCI-3212MP Handleiding

21 November 2024
Matterport

Matterport Pro2 3D Camera MC250 Handleiding

21 November 2024
Senal

Senal OLM-2S-P Handleiding

21 November 2024
Senal

Senal ME-220-CL Handleiding

21 November 2024
Senal

Senal ASM-4 Handleiding

21 November 2024