Frigidaire FRT21IS6JB Handleiding

Frigidaire Koelkast FRT21IS6JB

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire FRT21IS6JB (6 pagina's) in de categorie Koelkast. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
P/N 241857201 (Sept 2007)
Important Safety Instructions ........... 2
Installation .......................................... 3
Connecting Water Supply ................. 4
Door Removal Instructions ............... 5
Temperature Controls ....................... 8
Ice Service .......................................... 9
Normal Operating Sounds & Sights . 10
Care and Cleaning ............................. 10
Warranty ............................................. 12
Before you Call .................................. 13
Use & Care Manual
Refrigerator
Top Mount
Got Questions?
Need Parts or Service?
Before Calling Your
Local Repair Service - CALL:
(United States)
1-800-944-9044
(Canada)
1-800-668-4606
Resolve many service issues over the
phone at your convenience!
If we can’t resolve your service issue,
we’ll schedule a reputable local
service technician for you!
Order Genuine Electrolux Parts &
Accessories
Purchase Extended Warranty
Protection
Solutions Hotline
READ AND SAVE THESE INSTRUCTIONS
3
INSTALLATION
This Use & Care Manual provides specific operating
instructions for your model. Use the refrigerator only as
instructed in this Use & Care Manual. Before starting the
refrigerator, follow these important first steps.
LOCATION
Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.
If possible, place the refrigerator out of direct sunlight
and away from the range, dishwasher or other heat
sources.
The refrigerator must be installed on a floor that is level
and strong enough to support a fully loaded refrigerator.
Consider water supply availability for models equipped
with an automatic ice maker.
INSTALLATION
C AU TI ON C AU TI ON C AU TI ON C AU TI ON C AU TI ON
Do Not install the refrigerator where the temperature will
drop below 55°F (13°C) or rise above 110°F (43°C). The
compressor will not be able to maintain proper
temperatures inside the refrigerator.
Do Not block the toe grille on the lower front of your
refrigerator. Sufficient air circulation is essential for the
proper operation of your refrigerator.
Installation Clearances
Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:
Sides & Top 3/8”
Back 1”
N O T EN O T EN O T EN O T EN O T E
If you see black coils/tubing on the back of your refrigerator
(air-cooled condenser) leave 3” clearance at top of
refrigerator.
DOOR OPENING
Your refrigerator should be positioned to allow easy access to
a counter when removing food. To make this possible, the
direction in which the doors open can be reversed. See
Door
Removal & Reversal Instructions
.
N O T EN O T EN O T EN O T EN O T E
If your refrigerator is placed with the door hinge side against
a wall, you may have to allow additional space so the door
can be opened wider.
IMPORTANT
If you install your refrigerator in a garage or other unheated
area, you may experience freezer temperature problems
during the winter months when temperatures dip below
55° F.
Upgrading your refrigerator with a Garage Kit will lower the
minimum operating temperature of your unit to 34° F. This kit
can be ordered through the
Electrolux Solutions Hotline
(see
back cover).
LEVELING
All four corners of your refrigerator must rest firmly on a solid
floor. Your refrigerator is equipped with adjustable front rollers
or front leveling screws to help level your unit.
2. Use flat-blade screwdriver
or 3/8socket wrench to
adjust front rollers. Use
adjustable wrench to
adjust leveling screws.
Raise
Adjustable Front Roller
(some models)
Stationary Front Roller
with Leveling Screw
(some models)
N O T EN O T E
N O T EN O T E
N O T E
Raise the front of the refrigerator enough so the doors close
freely when opened halfway. The refrigerator should slope ¼
to ½” from front to back. Then level the refrigerator from side
to side.
To Level Your Refrigerator:
1. Remove toe grille.
4
CONNECTING HOUSEHOLD WATER SUPPLY TO REFRIGERATOR
Before Installing The Water Supply Line, You Will Need
Basic Tools: adjustable wrench, flat-blade screwdriver,
and PhillipsTM screwdriver
Access to a household cold water line with water pressure
between 30 and 100 psi.
A water supply line made of ¼ inch (6.4 mm) OD, copper
tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker
inlet valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the
refrigerator can be moved out for cleaning (as shown).
A shutoff valve to connect the water supply line to your
household water system. DO NOT use a self-piercing type
shutoff valve.
A compression nut and ferrule (sleeve) for connecting the
water supply line to the ice maker inlet valve.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket. Turn ON
water supply and flush supply line until water is clear. Turn
OFF water supply at shutoff valve.
3. Unscrew plastic cap from water valve inlet and discard
cap.
4. Slide brass compression nut, then ferrule (sleeve) onto
water supply line, as shown.
5. Push water supply line into water valve inlet as far as it
will go inch). Slide ferrule (sleeve) into valve inlet and
finger tighten compression nut onto valve. Tighten another
half turn with a wrench; DO NOT over tighten.
6. With steel clamp and screw, secure water supply line to
rear panel of refrigerator as shown.
7. Coil excess water supply line (about turns) behind
refrigerator as shown and arrange coils so they do not
vibrate or wear against any other surface.
8. Turn ON water supply at shutoff valve and tighten any
connections that leak.
9. Reconnect refrigerator to electrical power source.
10. To turn ice maker on, lower wire signal arm (see ice
maker front cover for ON/OFF position of arm).
IMPORTANT
Ensure that your water supply line connections comply with
all local plumbing codes.
N O T EN O T EN O T EN O T EN O T E
Water line kit number 5303917950, available from your
appliance dealer at additional cost, contains 25 feet (7.6
meters) of ¼ inch OD copper tubing, a saddle type shutoff
valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)
ferrules/sleeves, and instructions for installing a water supply
line.
W AR N IN G W AR N IN G W AR N IN G W AR N IN G W AR N IN G
To avoid electric shock, which can cause death or severe
personal injury, disconnect the refrigerator from electrical
power before connecting a water supply line to the
refrigerator.
C AU TI ON C AU TI ON
C AU TI ON C AU TI ON C AU TI ON
To Avoid Property Damage:
Copper tubing is recommended for the water supply
line. Water supply tubing made of ¼” plastic is not
recommended since it greatly increases the potential
for water leaks. Manufacturer will not be responsible
for any damage if plastic tubing is used for supply
line.
DO NOT install water supply tubing in areas where
temperatures fall below freezing.
Chemicals from a malfunctioning softener can
damage the ice maker. If the ice maker is connected
to soft water, ensure that the softener is maintained
and working properly.


Product specificaties

Merk: Frigidaire
Categorie: Koelkast
Model: FRT21IS6JB

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire FRT21IS6JB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Koelkast Frigidaire

Handleiding Koelkast

Nieuwste handleidingen voor Koelkast