Frigidaire FFTR1814WW Handleiding

Frigidaire Koelkast FFTR1814WW

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire FFTR1814WW (8 pagina's) in de categorie Koelkast. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
AUTOMATIC ICE MAKER
INSTALLATION INSTRUCTIONS
P/N: A13109106
WARNING
To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator
from electrical power before connecting a water supply line to the refrigerator.
Connect the ice maker to a potable water supply only.
An authorized service technician is recommended to install the ice maker kit.
Ice Maker (IM117000) Kit Components
5304520536
Ice Maker
QTY: 1
5304525288
Shoulder Screw
QTY: 5
5304520538/5304520539
Cover with Door
QTY: 1
5304520535
Ice Bin
QTY: 1
5304520537
Bracket (30" only)
QTY: 1
Parts needed for install inside the unit
Tools Needed:
Flat head screw driver Phillips or Quadrex driver
¼" Hex driver Gloves
Drill Needle nose pliers
Parts needed for install on back side of the unit
NOTE
Check with your local building authority for recommendations on water lines and associated materials prior to
installing your new refrigerator. For household water line hookup from the home water supply system to the unit,
Frigidaire recommends for homes with existing valves its Smart Choice® water line kit 5304437642 (with a 6
Stainless Steel Water Line) and for homes without an existing valve, Frigidaire recommends its Smart Choice®
water line kit 5304493869 (with a 6 Polyline Waterline). Please refer to Frigidaire.com for more information.
5304520540
Water Valve
QTY: 1
218976923
Tube
QTY: 1
241500304
#8 screw
QTY: 2
218515401
Hose and
Harness Clip
(30" only)
QTY: 3
5304455846
Clamp " ¼
QTY: 1
5303001193
Clamp "½
QTY: 1
2
Ice Maker Installation Instructions
1. Unplug refrigerator from electrical outlet.
2. Lift the freezer shelf up and out. Set aside.
See Figure 1.
3. Remove water inlet and electrical cover, located
on the inside of the unit, by inserting a flathead
screwdriver on left side of opening in the small
cover. Push to the right to disengage the snap.
See Figure 2.
4. Locate dimples in the freezer liner for screw
placement (a flashlight may help). Align the
shoulder screws with the dimples. Push the
screws to penetrate the freezer liner and drive the
screws in until they are tight against the liner. Use
2 screws on the left side wall, and 3 on the top of
the liner. See Figure 3.
5. For a "30 wide refrigerator install the bracket
onto the ice maker. The Ice maker will slide onto
the mounting features on the bracket and snap
into place. The locking feature is located on the
rear of the ice maker.
6. Plug the ice maker in the electrical connector on
the back wall. Once connected, do not allow the
ice maker to hang unsupported. See Figure 4.
7. Slide the ice maker onto the 2 side wall shoulder
screws. See Figure 5A.
Make sure the ice maker water channel is under
the water ll tube, continue to slide until the ice
maker snaps into place. See Figure 5B.
28 wide refrigerator "
Use the ice maker only
Locking
Feature
1
2
30 wide refrigerator"
Use the bracket with the ice maker
Figure 1
Figure 2
To Ceiling
To Wall
Install 5
Shoulder
Screws
Figure 3
Plug
Electrical
Connector
Figure 4
Figure 5
A
B
3
Ice Maker Installation Instructions
9. To install the ice bin, the freezer shelf needs to be
in the lowest position. Slide the ice bin between
the side wall and the right side of the ice maker
housing positioned on the shelf. See Figure 7.
10. Locate the Ice maker installation label on the
rear outside right top corner of the refrigerator.
Cut the label on the dashed lines, and push flaps
inward until they stick to the unit. See Figure 8.
8. Install the plastic shutter into the window in the
front of the cover. The shutter snaps into the clips
on inside face of the cover, no tools are required.
Slide the ice maker cover onto the shoulder
screws on top of the unit until it locks into place
with a snap. See Figure 6.
11. Install the water line by screwing the nut on the
end of the tube onto the water inlet. Tighten the
nut until snug, and then tighten an additional ¼
turn with needle nose pliers. (See Figure 9A.)
12. Install the 2 water line clips on the unit evenly
spaced inside the depressed area located under
the water inlet. Insert the water line tube into the
clips. (See Figure 9B.)
*If you have a unit with an access cover,
continue to page 4 for additional instal-
lation instructions. For a unit without an
access cover, continue to page 5.
Units with access cover
Units without access cover
Figure 6
Figure 7
Cut on dashed lines
and push in on flaps
Figure 8
Water
Line
Clip
Water
Inlet
A
B
Figure 9


Product specificaties

Merk: Frigidaire
Categorie: Koelkast
Model: FFTR1814WW

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire FFTR1814WW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Koelkast Frigidaire

Handleiding Koelkast

Nieuwste handleidingen voor Koelkast