Frigidaire FFDI502CMS Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire FFDI502CMS (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
All about the
Use & Care
of your
TA B L E O F C O N T E N T S
www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352
Food Waste Disposer
560C525P02 RevB (September 2011)
Product Registration ........................................... 2
Important Safety Instructions .............................. 2
Removal of Old Unit ........................................... 3
Installation of Mounting Assembly ................... 4 - 5
Electrical Connections ........................................ 6
Operating Instructions ........................................ 7
Troubleshooting................................................. 8
Cleaning and Maintenance .................................. 8
Notes ............................................................... 9
Warranty ........................................................ 10
2
Bill of sale, sales slip, cancelled check or other purchase
record should be kept to verify the original purchase date for
warranty purposes.
©2009 Electrolux Home Products, Inc. All rights reserved. Printed in the USA
PRODUCT REGISTRATION
Model Number*
Serial Number*
*Above information appears on the label affixed to bottom of
the disposer. For your convenience, write down the model and
serial numbers prior to installation.
See insert for specific information about your new
disposer:
NOTE: This Food Waste Disposer has been designed to
operate on 110-120 Volt, 60Hz exclusively. Using any other
voltage or Hz adversely affects performance.
IMPORTANT: Read all instructions thoroughly. Keep this
guide for future reference.
CAUTION: Be sure to review SAFETY INSTRUCTIONS
FIRST PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK
OR INJURY TO PERSONS before using disposer.
Call our toll free Help Line with any questions:
800-944-9044
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS.
SAVE THESE INSTRUCTIONS.
Warning: When using electrical appliances, basic precaustions should always be followed, including the following:
1. Read all instructions before using the appliance.
2. To reduce the risk of injury, close supervision is neces
sary when an appliance is used near children.
3. Do not put fingers or hands into a waste disposer.
4. Turn the power switch to the off position before at
tempting to clear a jam or remove an object from the
disposer.
5. When attempting to loosen a jam in a waste disposer,
use a long wooden object such as a wooden spoon or
the wooden handle of a broom or mop.
6. When attempting to remove objects from a waste
disposer use long-handled tongs or pliers. If the dis
poser is magnetically actuated, non-magnetic tools
should be used.
7. To reduce the risk of injury by materials that may be
expelled by a waste disposer, do not put the following
into a disposer: clam or oyster shells; caustic drain
cleaners or similar products; glass, china or plastic;
large whole bones; metal, such as bottle caps, tin cans,
aluminum foil or utensils; hot grease or other hot
liquids; whole cornhusks.
8. When not operating a disposer, leave the stopper in
place to reduce the risks of objects falling onto the
disposer.
9. DO NOT operate disposer unless splash guard is in
place. (Does not apply to the Top Control/Batch Feed
units.)
10. For proper grounding instructions see the ELECTRICAL
CONNECTION portion of this manual.
Note: if you are not familiar iwth electrical power and procedures, call a qualified electrician.
Warning: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check
with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not
modify the plug provided with the appliance if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
3
REMOVAL OF OLD UNIT
TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY
Before starting this step, turn off electrical power
at the circuit breaker or fuse box.
If your old mount is the same as the mount on your new
disposer, just reverse the assembly instructions found in
section Installation of Mounting Assembly. If your new
mount system is different, follow these instructions:
A. Use a pipe wrench to disconnect drain line where it
attaches to disposer discharge tube (see A).
B. Remove disposer from sink flange by turning mount ring
to the left clockwise (see B). If you are unable to turn
the mount ring, tap on one of the extensions from the
ring with a hammer. Some mounting systems have
tubular extensions. Inserting a screwdiver into on tube
will provide additional leverage for turning the mount
ring (see B). Some disposers may require the removal
or loosening of nuts from the mount screws (see C).
Some disposers may require the removal of a clamp.
IMPORTANT: Unless you have a new home, this is a
good time to clean out the trap and drain lines by
running a drain auger or plumber’s snake before
installing your new disposer.
Caution: Be sure to support the disposer while
perfomring this step or it may fall when the
mounting ring is disconnected from the mounting
assembly. If your disposer is hard wired (metal
shielded cable not utilizing a wall plug), complete
steps C and D. If you utilize a plug- in cord, go
on to step E.
C. When disposer is removed, turn up side down and
remove electrical cover plate (see D).
D. Use screwdriver to remove green ground wire. Remove
wire nuts from black and white power wires and
separate disposer wires from power cable wires.
Loosen screws on cable clamp and separate cable from
disposer.
E. To remove remaining mount system from the sink,
loosen mount screws, push mount ring up. Under it is
the snap ring. Use screwdriver to pop off ring (see E).
Remove mount ring, protector ring and gasket from sink
flange. Some mounts will require the unscrewing of a
large ring holding the sink flange in place. Pull sink
flange up through sink and clean off old putty from sink.
DISHWASHER CONNECTION
procedure. If dishwasher is not to be connected go to
section Installation of Mounting Assembly.
A. Using a blunt instrument (steel punch or wooden dowl),
knock out entire plug (see A). Do no use a screwdriver
or sharp instrument. When knockout plug falls into
disposer, ou may remove it or simply grind it up when
the disposer is used. This will not damage the disposer
in any way, but may take sometime to grind, over the
course of several uses. Go to section Installation of
Mounting Assembly.
B. Connect dishwasher hose using hose clamp. If hose size
is different, you will need a Dishwasher Connector Kit
(see B). Make sure all plumbing connections are tight
and in accordance with all plumbing codes and ordinan
ces. Run water and check for leaks.
If you are utilizing a dishwasher, complete the following


Product specificaties

Merk: Frigidaire
Categorie: Niet gecategoriseerd
Model: FFDI502CMS

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire FFDI502CMS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Frigidaire

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd