Frigidaire F36WC19ES Handleiding

Frigidaire Ventilator F36WC19ES

Lees hieronder de 📖 handleiding in het Nederlandse voor Frigidaire F36WC19ES (8 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-

JURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac-

turer. If you have questions, contact the manufacturer at

the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at ser-

vice panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the

service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhaust-

ing of gases through the flue (chimney) of fuel burning equip-

ment to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code au-

thorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any solid-state speed control de-

vice.

8. To reduce the risk of fire, use only metal ductwork.

9. Use with approved cord-connection kit only.

10. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when

cooking flaming foods.

3. Clean ventilation fans frequently. Grease should not be al-

lowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for

the size of the surface element.

IMPORTANT

For Non-ducted (Ductfree) Installation:

a) Purchase non-ducted filter separately.

b) Remove and discard damper/duct connector and louver cover

(See Step 4) in “Prepare the Hood,” Page 2.

c) Follow all steps except steps inside dotted lines.

For Ducted Installation:

Follow all steps, including steps inside dotted lines.

F30WC, F36WC, & F42WC SERIES

4-WAY CONVERTIBLE RANGE HOOD

READ AND SAVE THESE INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO PRE-

VENT BURNS. If the flames do not go out immediately, EVACU-

ATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you

already know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/

or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit.

3. Your hood motor has a thermal overload which will automatically

shut off the motor if it becomes overheated. The motor will

restart when it cools down. If the motor continues to shut off

and restart, have the hood serviced.

4. For best capture of cooking impurities, your range hood should

be mounted 18-24" above the cooking surface.

5. Please read specification label on product for further information

and requirements.

WARNING

INSTALLER: Leave This Manual With

the Homeowner.

HOMEOWNER: Use and Care

Information on Page 5.

FIG. 1B

FIG. 1C

FIG. 1D

FIG. 1E

6" ROUND DUCT 3-1/4" x 10"

TO 6"

ROUND

DUCT

TRANSITION

WALL CAP

3-1/4" x 10" DUCT

ROOF CAP

3-1/4" x 10" DUCT

ADJUSTABLE ELBOW

WALL CAP

3-1/4" x 10" TO

6" ROUND

DUCT

TRANSITION

ROOF CAP

6" ROUND

DUCT

TOOLS AND

MATERIALS REQUIRED

TOOLS

❏Drill, electric or ratchet drive

❏1-1/4" Spade bit

❏Common head and phillips head screwdriver

❏Pliers

❏Tape measure or ruler and pencil

For Ducted Installations ONLY:

❏ Saber saw or drywall saw

❏ Metal snips

MATERIALS

❏Electrical wiring and supplies of type to comply with local

codesFor Ducted Installations Only:

❏ Roof or wall cap

❏ Roof cement or caulk

❏ Duct and duct tape

For Installation on Kitchen Cabinets with Recessed Bottoms

Only:

❏Two 1" x 2" x 12" (approximate length) wood strips (pur-

chase locally)

❏Four 1-1/4" long flat head wood screws (purchase locally)

to fasten strips to cabinet bottom

PLANNING DUCTWORK

INSTALLATION

Begin planning ductwork by deciding where the duct will run

between the range hood and the outside. For best performance,

use the shortest possible duct run and a minimum number of

elbows. There are several choices shown - FIGS. 1A - 1E.

In more complex ducting situations, a 3-1/4" rectangular ducting

range hood can be converted to a round duct by means of a

transition.

FIG. 1A. Ducting directly through the wall (for range hoods

mounted on an exterior wall). Shown are two ways to duct through

an outside wall. If a wall cap is used directly off the back of the

hood, special care must be taken to make sure that the damper

in the damper/duct connector on the hood and damper in the

wall cap do not interfere with each other when the hood is oper-

ating. This could result in either inadequate air delivery or back

drafts. If this condition does exist, remove the hood damper flap.

Sometimes when using a wall cap it is easier to duct vertically

and then use an elbow as shown in FIG. 1B.

FIG. 1C. Ducting straight up through the roof using

3-1/4" x 10" rectangular duct. (For single story installations.)

FIG. 1D. Ducting between the ceiling joists (for multi-story instal-

lations) or through the soffit space above the cabinets (where

the soffit connects to an outside wall).

FIG. 1E. Straight up through the roof using 3-1/4” x 10” to 6”

round duct transition and 6" round duct (for single-story installa-

tions).

FIG. 1F. Straight up through the roof using 7" round duct (for

single-story installations). Requires optional damper Model Damp

Kit available from your local dealer.

FIG. 1A

7" ROUND DUCT

DAMPER

MODEL

“DAMPKIT”

ROOF CAP

FIG. 1F

FIG. 2

FIG. 5

FIG. 6

FIG. 7

CUT STRIPS TO FIT

CENTER

LINE

WIDTH OF

RANGE

HOOD

ELECTRICAL

WIRING OPENING

FIG. 3

DUCT

OPENINGS

PREPARING THE RANGE HOOD

1. Unpack hood and check contents. You should receive:

1 - Aluminum Filter

1 - 3-1/4" x 10" Damper/Duct Connector (mounted inside of

hood for shipping only) (Save screws for mounting.)

1 - 7” Round Duct Plate (mounted on top of hood) (not shown)

(Save screws for mounting.)

2. Remove 7” round duct plate from top of hood. Set duct plate

aside - with mounting screws.

3. Remove wiring box cover. Under cover find:

PREPARING THE

INSTALLATION LOCATION

FIG. 4

WIRING BOX

COVER

DAMPER/DUCT CONNECTOR

ALUMINUM

FILTER

For Ductfree Installations Only:

4. For ductfree installation, remove louver cover from front (or

inside) of hood. (FIG. 3)

NOTE

Louvers on front of hood must be open and visible

for hood to function in ductfree mode.

5. Remove either top or rear electrical knockout depending upon

whether wiring will enter hood from wall or cabinet. (FIG. 4)

DUCTED INSTALLATION ONLY

NOTE

Louver cover must be installed as shown in Figure 3 to

function in ducted mode.

6. Remove appropriate duct knockout on hood by inserting

screwdriver into edge of knockout and breaking tabs holding

knockout to hood. You may have to tap screwdriver with ham-

mer to break tabs. Peel knockout back with pliers. (FIG. 5)

7. Fit damper/duct connector over opening and secure in place with

black sheet metal screws. (FIG. 6)

Hinge pins and damper/duct connector should be toward top

of hood for ducting through wall or toward back of hood for

ducting through cabinet above hood. Seal joint between

damper/duct connector and hood with duct tape.

8. 7” round ducted discharge only: Re-install 7” round duct

plate removed in Step #2 under “PREPARING THE RANGE

HOOD” section. For best performance, line up the 7” round

duct plate with the 7” round opening on hood. Mount duct

plate to hood with 2 screws from duct plate and 2 screws

from 3¼” x 10” damper. Install a 7” round damper (purchase

separately). Damper flap must open freely in direction of air

flow (away from range hood).

KEYHOLE SLOTS

NOTE

MOUNT HOOD SO THAT BOTTOM OF HOOD IS 18"-24" ABOVE

COOKING SURFACE. TOP FRONT EDGE OF HOOD SHOULD

BE FLUSH WITH FRONT OF CABINET FRAME.

IF DISTANCE BETWEEN WALL AND FRONT OF CABINET

FRAME IS MORE THAN 12" THERE WILL BE A SPACE BE-

TWEEN BACK OF HOOD AND WALL. THIS IS NORMAL.

OMIT STEP 9 if range hood will be installed under cabinets

with flush bottom.

9. (For installation on recessed bottom cabinets only) Attach a

wood filler strip at each side of recessed area under cabi-

net. (Use two 1" x 2" strips cut to length.) If recess is more

than 1" use thicker strips. Attach strips with 1-1/4" screws

about 3" from each end. See FIG. 7.

10.Measure and mark the following (FIGS. 7 & 8):

a) Electrical line opening

b) Duct opening

11.Drill four pilot holes in corners of marked duct opening as

shown and cut opening with saber saw or keyhole saw.

12.Use 1-1/4" drill bit to drill opening for electrical connection

in wall or cabinet.

13.Hold hood up against cabinet bottom and trace keyhole slots

onto cabinet bottom of filler strips.

14.Screw the four supplied 7/8" wood screws for mounting the

hood into the exact center of the narrow end of the keyhole

slots marked underneath the cabinet. Allow 3/8" of the

screws to project, so the hood can be fitted into place.

Product specificaties

Merk:	Frigidaire
Categorie:	Ventilator
Model:	F36WC19ES

Heb je hulp nodig?

Als je hulp nodig hebt met Frigidaire F36WC19ES stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Ventilator Frigidaire

Frigidaire FCVW3062AS Handleiding

26 December 2023

Frigidaire FCVW3062AD Handleiding

26 December 2023

Frigidaire F36WC19EC Handleiding

4 Juni 2023

Frigidaire PLHV36W7CC Handleiding

18 Mei 2023

Frigidaire UCVH2001AS Handleiding

14 Mei 2023

Frigidaire F30WV16EC Handleiding

2 Mei 2023

Frigidaire PLHV36W6CC Handleiding

29 April 2023

Frigidaire PLHV42P8CC Handleiding

25 April 2023

Frigidaire F30WV16EB Handleiding

24 April 2023

Frigidaire F30WR01ES Handleiding

16 April 2023

Handleiding Ventilator

Nieuwste handleidingen voor Ventilator

Aerian MISTY100 Handleiding

17 November 2024

Tornado HI-FAN-24HVWM-1P Handleiding

17 November 2024

Tornado HI-FAN-24PF-1P Handleiding

17 November 2024

Tornado HI-FAN-24MOWF-A-1P Handleiding

17 November 2024

Tornado HI-FAN-20HVWM-A-1P Handleiding

17 November 2024

Tornado HI-FAN-20WMPRO-1P Handleiding

17 November 2024

Tornado HI-FAN-24MOWF-WR-1P Handleiding

17 November 2024

Tornado HI-FAN-30HVOF-1P Handleiding

17 November 2024

Tornado HI-FAN-30POF-WR-1P Handleiding

17 November 2024

Tornado HI-FAN-20POF-5BA-1P Handleiding

17 November 2024