Franke TP-125 Handleiding

Franke Niet gecategoriseerd TP-125

Lees hieronder de 📖 handleiding in het Nederlandse voor Franke TP-125 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 168 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

FOOD WASTE DISPOSER

FRANKE TURBO PLUS OWNERS GUIDE

Important - Read all instructions thoroughly

Please retain for future reference

1. Read all instructions before using the appliance.

2. To reduce the risk of injury, close supervision is necessary

when an appliance is used near children.

3. Do not put fingers or hands into a waste disposer while it

is functioning.

4. Turn the power switch to the off position before attempting

to clear a jam or remove an object from the disposer.

5. When attempting to loosen a jam in a waste disposer,

use a long wooden utensil e.g. spoon.

6. When attempting to remove objects from a disposer, use

long-handled tongs or pliers.

7. To reduce the risk of injury please note:

- this disposer is not for grinding hard materials, such as

glass and metal;

- this disposer must be connected to the electric supply by

means of either a power supply cord or insulated wires in a

flexible conduit;

- when installing the disposer, care must be taken to ensure

that the reset button of the overload protection device

remains readily accessible.

8. Additionally for continuous feed models:

- Care must be taken to ensure that the supply is

disconnected by switching off the electric supply or by

removing the plug from the socket-outlet before freeing a

jammed rotor.

- When not operating the disposer, leave the stopper in place

to reduce the risk of objects falling into the disposer.

- Do not operate disposer unless splash guard is in place.

9. For proper electrical earth instructions see the

ELECTRICAL CONNECTION details of this manual.

10. All installations should be carried out by a qualified electrician.

11. The symbol on the product or on its packaging indicates

that this product may not be treated as household waste.

Instead, it shall be handed over to the applicable environmental

collection point for the recycling of electrical and electronic

equipment. For more detailed information about recycling of

this product, please contact your local authority, your

household waste disposal service or the shop where you

purchased the product.

IMPORTANT SAFETY INSTRUCTIONS

Instructions pertaining to risk of fire, electric shock or injury to persons.

Save these instructions.

WARNING - When using electrical appliances, basic precautions should always be

followed, including the following:

www.franke.co.uk

For overﬂow or dishwasher connections, complete the

following procedure. Alternatively go on to section 3.

1 Using a blunt instrument (steel punch or wooden dowel),

knock out entire plug (see 1A). Do not use a screwdriver or

sharp instrument. (When knockout plug falls into Disposer,

you may remove it or grind it up when the disposer is used.

This will not damage the disposer in any way, but may take

some time to grind over the course of several uses).

2 Connect dishwasher hose (see 1B) using a hose clamp.

Make sure all plumbing connections are tight and in accordance

with all plumbing codes and ordinances. Run water and check

for leaks.

1. OVERFLOW/APPLIANCE CONNECTIONS

KNOCK

OUT PLUG

WOOD OR

METAL DOWEL

RUBBER

H OSE

DISHWASHER

HOSE

AI GAR P

*Air gap may not be require d

for all ins allations. Check loca t l

plumbing codes .

DRAIN

D RISPOSE

WHEN YOU DO NOT WISH TO UTILISE THE AIR SWITCH

(e.g. if hard wiring the WDU to a standard electrical switch)

Follow the following procedure:

1 With the disposer mounted on the sink and the unit connected

to the mains, turn ON the wall mounted switch.

2 Connect the air switch tube to the nipple on the underside

of the unit.

3 If the disposer is OFF, depress air switch actuator to

turn the disposer ON.

4 With the disposer ON pull air switch hose from disposer

connection and discard air switch actuator and hose.

5 Turn the disposer OFF by turning off the switch, usually

controlled by a wall mounted switch.

6 Operation of disposer is now controlled in a typical manner

by the wall mounted switch.

FRANKE TURBO PLUS MODELS

TP-50

Continuous Feed

TP-75

Continuous Feed

TP-125

Continuous Feed

TP-125B

Batch Feed

136

356

193

270

295

218

381

136

330

253

416

136

330

253

491

136

A Disassemble the mounting assembly, as it has been shipped,

by turning the sink flange until the projections align with the

notches in the mount ring and allow you to pull the sink flange

up and out of the remaining mount assembly. Note the

sequence of these parts as they are stacked and refer to A

and B to identify each part. Unpack the 3 mount screws and

screw them half way through the mount ring (notice “THIS

SIDE UP” is imprinted on top of the mount ring). Next, stack

the rubber gasket on top of the protector ring and sit them on

top of the pointed ends of the mount screws.

B Keep these assembled parts together and set aside. Before

you connect the disposer to the mount assembly under the

sink, you may want to practice engaging the groove of the

cushion ring to the ridge at the bottom of the sink flange

(see A and read Sec. 5).

C Be sure your sink is clean. Pack the underside rim of the sink

flange with plumber’s putty (see C). Position the sink flange so

it is centered and readable as you look into your sink. Push the

sink flange firmly into the sink opening to make a good seal.

DO NOT move or rotate the sink flange once seated or the seal

may be broken.

D Take the remaining portion of the mount assembly, as it was

set aside and make sure that the rubber gasket is on top of the

protector ring. From under the sink, while holding the sink

flange firmly with one hand, line up the notches in the mount

ring with the projections of the sink flange. Slide the mount

assembly up onto the sink flange, past the projections and

give the mount assembly a 1/4 turn, so that it will hang by

itself (see D).

E Tighten the 3 mounting screws evenly with a screwdriver

(see E). DO NOT OVERTIGHTEN! Trim off excess putty.

2a. INSTALLATION OF 3-BOLT MOUNTING ASSEMBLY

For TP-50, TP-75 and TP-125 models. Read completely before starting

NB - Pay close attention to the order of mount assembly parts,

as they have been correctly assembled by the factory.

(See A and B.)

metsyS tnuoM tloB-3

PROTECTOR RING

SINK MOUNT RING

MOUNTING SCREWS (3)

SINK FLANGE

SINK FLANGE GASKET

STOPPER*

SINK FLANGE**

SINK

HOPPER

ELBOW

GASKET

SCREWS

SERIAL #- RECORD ON

WARRANTY CARD

MOUNTING

SCREWS**

SCREW

CLAMP**

PROJECTIONS

RIDGE

DISCHARGE

ELBOW

FLANGE

DISHWASHER

DISCHARGE INLET

CUSHION RING**

RUBBER SINK

FLANGE GASKET**

PROTECTOR RING**

MOUNT RING**

PLUMBER’S

PUTTY

END BELL

(ELECTRICAL

CONNECTIONS)

* Batch Feed Stopper looks different than the stopper illustrated.

** Mount Assembly (see B) 2

MOUNTING

SCREWS

PROTECTOR

RING

RUBBER

GASKET

SINK

FLANGE

CUSHION RING

SCREW

CLAMP

MOUNTING

RING

Mount Assembly

C D E

Product specificaties

Merk:	Franke
Categorie:	Niet gecategoriseerd
Model:	TP-125
Kleur van het product:	Grijs
Breedte:	269.6 mm
Diepte:	269.6 mm
Hoogte:	416 mm
Soort:	Afvalverwerkingssysteem voor gootstenen
Inhoud:	- ml
Rotatiesnelheid:	2800 RPM
Motorvermogen:	1.25 hp
Type doorvoer:	Doorlopende toevoer