Foscam FHC994 Handleiding
Foscam
Beveiligingscamera
FHC994
Lees hieronder de đź“– handleiding in het Nederlandse voor Foscam FHC994 (3 pagina's) in de categorie Beveiligingscamera. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/3
How to setup and operate the FHC994 – Quick Start Guide
Basic Operations
1. Insert the microSD card (up to 64GB) into the microSD card slot (metal contacts facing up) located on one side of
the FHC994. NOTE: The card must be formatted to FAT32. Most cards 32GB and below are default to FAT32.
64GB cards will need to be formatted.
2. Move the slider located on the FHC994 to the desired recording mode. There are three types of
recording modes as follows:
The left-most mode is the “Surveillance Mode”. This mode shows the symbol of an eye on the FHC994.
This mode records continuously until the microSD card is full. It then overwrites the oldest recordings
and continues creating recordings (circular recording is enabled on this mode). To record as much video
as possible, this mode records in VGA resolution (640 x 360).
The middle option is called “On-The-Go” mode, which shows a symbol of a running man. This mode records
when motion detection is detected and for 2 minutes after the last motion was detected. This mode also
uses circular recording (your oldest recordings will be deleted in order to store new recordings). This mode
utilizes recording at a 720p resolution (1280 x 720).
The right-most mode is the “Custom Mode”. Please refer to the Custom Mode Setup for instructions on how to set up
custom configurations.
3. Power on the FHC994 by holding the power button for about 2 seconds. You will notice the LED indicator
becomes active. Depending on what mode the FHC994 is in, you will see the following variations:
Without DC adapter
Solid Green LED: camera is booted up
Solid Red LED: no card, card failure, low battery, or card is full (not in loop recording mode)
Flashing Green LED: camera is recording normally
Green / Red LED intermittent flashing: battery low and recording
DC adapter plugged in
Solid Orange LED: charging but not recording
Solid Green LED: charging complete but not recording
Flashing Green LED: charging complete and recording
Flashing Green & Orange: charging and recording
Solid Red LED: no card, card failure or card is full (not in loop recording)
Connected to computer
Solid Orange LED: charging
Solid Green LED: charging complete
4. To view your recordings, plug the FHC994 into your computer using the provided USB cable. The camera
Will appear as a removable disk, and should appear in “My Computer” (on Windows). On Mac, open up “Finder”
and the device will appear on the left side.
Inside the device will be a folder labeled “DVR”. This folder holds all recordings made on the FHC994. From here,
you can view, copy, or delete any recordings you wish.
NOTE: The camera cannot record while connected to a PC.
Format as FAT32: Most MicroSD Cards 32GB and under are already in FAT32 format. 64GB cards normally are exFAT
format. If your card is not FAT32, please use the process below to format the card:
1. Insert the card into the camera, connect the camera to the PC, and determine the drive designation (i.e., G:\,
H:\, etc.)
2. Download the fat32format utility in GUI version from here: http://foscam.us/downloads/guiformat.exe. Click on
the picture to retrieve the file.
3. Launch the guiformat.exe.
4. Choose the drive that corresponds to your SD card.
5. Check the Quick Format box.
6. Press Start.
Once it has finished, your MicroSD card should now work with the camera.
Custom Mode Setup
To setup Custom Mode (the third mode on the right side of the FHC994 slider), the Foscam DVR widget needs
to be installed on your PC or Mac.
The DVR Widget can be found at http://www.foscam.us/pc-software-widget for both PC and Mac.
NOTE: Some antivirus programs have been known to flag this as a virus. This program is safe and
an exception may need to be created within your antivirus program. This program contains no
bloatware or unneeded add-ons.
1. Ensure the FHC994 is set to Custom Mode. To do this, move the slider to the far right. Custom Mode is designated
by a gear icon above the slider.
2. Plug the FHC994 into your PC or Mac using the provided USB cable adapter.
3. Open the Foscam DVR Widget that you installed. (DVR Widget can be found at
http://www.foscam.us/pc-software-widget)
4. Once the software widget is open, you should see the following screen below. At this point we recommend
syncing the date and time to the FHC994 as it will make it easier to find your recordings when you check the
camera in the future. To sync the date and time, click on the section on the left of the software titled “Date Time”.
From this point, change the time and date according to your specifications. Once done, click on the blue highlighted
text on the top right that reads “Sync Settings to DVR”.
5. To edit settings, click on the “Settings” section
on the left side of the software. You should see a list of
preset features that can be adjusted with a description of each
preset. After you have selected the desired preset, click the
blue highlighted text which states “Sync Settings to DVR”.
You can now disconnect the camera and start using it.
If the preset options do not suit your needs, you can customize
the FHC994’s settings even further. To do this, click on the
“Option” category on the left of the software, and ensure the
“Setting Mode” is set to “Custom Mode”. Click the blue
highlighted text on the top right labeled “Save Option” to
change the mode. Then head back to the “Settings” section,
you should see the list of features to adjust.
Once you have adjusted the settings you need, click the blue
highlighted text on the top right that reads “Sync Settings to
DVR”. You can now disconnect the camera and start using it.
www.foscam.us
Foscam FHC994 Wide Angle HD Security Camcorder User Manual
Overview
Congratulations on your purchase of the Foscam FHC994 wide angle HD intelligent security camcorder!
The Foscam FHC994 is an intelligent security camcorder with rotatable 160deg camera and multiple
triggering methods and multi auto on/off modes. The camcorder comes with a built-in rechargeable
battery which can record up to 10 hours continuous video during typical use and standby for more
than 4 months when vibration triggering is enabled. By plugging in the 5V DC adapter, it can achieve
64 hours of looped recording for surveillance use.*
* Actual life and performance may vary depending upon usage and settings; battery not replaceable.
Charging
The camcorder comes with an internal rechargeable battery. When using the camcorder for the
first time, or if you are using it after a long period of non-usage, remember to fully charge the battery
for at least 6 hours and resync the time by using the widget (see section “PC Software
Widget”). You can charge your camcorder using the USB port of your computer, the DC adapter, or
using a car adapter.
To charge the battery through USB port, connect the USB cable to the USB port of the
computer and the camcorder. For details, please see the status below. The camcorder will
function as a mass storage device, you will not be able to record video at this moment.
To charge the battery through a DC adapter or car adapter, connect the DC adapter or car
adapter to the camcorder. For details, please see the Status section below. Moreover, you will also be
able to record video while charging, depending on the mode you set.
Features
Circular recording – Also known as “loop recording”. Overwrites recordings once memory card is full.
Time stamp – Inserts a time stamp onto the video.
Scheduled recording - set the time to automatically turn on / off recording, 7-day circular.
Vibration-trigger recording – Select this to record only when vibration is detected.
Motion-trigger recording – Select this to record only when motion is detected.
Voice-trigger recording – Select this to record only when voice/talk is detected.
Auto on/off mode – Select different auto on/off scenarios.
Selectable day/night mode – Select day mode or night mode to suit your environment.
Auto gapless split file – Splits files without gaps at every 10 / 15 / 20 minutes of recording.
Orientation – Use when the camcorder is turned upside-down.
Selectable resolution – Select a resolution of 1280x720(720p) or 640x360(360p) video and sound.
Frame rate adjustment – Adjust or lower the frame rate to save memory space.
Configurable video quality – high / medium / low
Support max 64GB microSD (TF) card (for better performance, use a card with class 4 or
above and format the card before usage. Check the following link for more information:
(http://www.softpedia.com/get/System/Hard-Disk-Utils/HP-USB-Disk-Storage-Format-Tool.shtml)
Recording
The power button is located on the right side of the camcorder. It can turn the camcorder on
or off.
Start Recording
Press and hold the Power button until the green LED is on (approximately 2 seconds), and
then release the button. When you see the green LED flashing, the camcorder is recording.
If you see otherwise, please read the Status section below.
Stop Recording
Press and hold the Power button until the green LED is off (for approximately 2 seconds).
WARNING: Turn off the camcorder before removing the card!
Minimum System Requirements
Windows 2000, XP, Vista, 7, 8, Mac OS X (mass storage class)
Windows Media Player 9
Intel Pentium class computer
USB 2.0 port for hi-speed transfers and charging
Status
Without DC adapter
Green LED on: camcorder is booted up
Red LED on: no card, card failed, battery low, or card is full (not in circular recording)
Green LED flashing: normal recording
Green / Red LED intermittent flashing: battery low and recording
DC adapter plugged in
Orange LED on: charging but no recording
Green LED on: charging complete but no recording
Green LED flashing: charging complete and recording
Green / Orange LED intermittent flashing: charging and recording
Red LED on: no card, card fail or card full (not in circular recording)
Connected to computer
Orange LED on: charging
Green LED on: charging complete
Package Contents
Please unpack your intelligent security camcorder and check that the following were included:
Foscam FHC994 intelligent security camcorder
5V DC Adapter
USB 2.0 Cable
User Manual
Quick Start Guide
Foscam FHC994 at a Glance
LED indicator
on/off
camera
USB port
card slot
surveillance mode
custom mode
On-the-GO mode
microphone
www.foscam.us
Foscam FHC994 Intelligent Security Camcorder User Manual
Mode switch
Switch between surveillance, on-the-go and custom modes. Default settings are in parentheses.
Note: For custom mode configuration, please use the third party PC software Widget to change
the settings. The widget can be downloaded from www.foscam.us/pc-software-widget. To make the
custom mode settings effective, please push the mode switch to the “custom
mode” position before powering up the FHC994.
Surveillance
Video Quality
Resolution
Frame Rate
Indoor Lighting
Condition
Day / Night Mode
Orientation
Time Stamp
Circular Recording
Split File Time (min)
Mic
LED On / Off
Voice-Trigger
Sensitivity
Vibration-Trigger
Sensitivity
Vibration Standby Mode
Motion-Trigger
Sensitivity
Auto On / Off
High
640x360
High
50Hz
Day mode
Normal
Enable
Enable
20
Enable
On
Disable
Disable
N/A
Disable
On-the-GO
High
1280x720
High
50Hz
Day mode
Normal
Enable
Enable
15
Enable
On
Disable
Disable
N/A
Medium
Custom (default)
(High) / Medium / Low
1280x720 / (640x360)
(High) / Low
(50Hz) / 60Hz
(Day mode) / Night mode / Auto
switching
(Normal) / Up-side-down
(Enable) / Disable
(Enable) / Disable
10 / (15) / 20
(Enable) / Disable
(On) / Off
High / Medium / Low / (Disable)
High / (Medium) / Low / Disable
Fast Wake Up / (Power Saving)
High / Medium / Low / (Disable)
PC Software Widget
To synchronize the time and customize settings, download a PC software “Widget” from the following website:
www.foscam.us/pc-software-widget - follow the instructions in the software guide.
NOTE: If the time shown is year 2026 or beyond due to a loss of Real Time Clock,
recording time will not be shown on the video, even if the timestamp is enabled. Please use
the widget to resync the time and delete files created in 2026 or beyond!
Connecting to computer
To
1
2
3
connect the camcorder to your computer, follow these instructions:
Connect the larger end of the USB cable into an available USB port on the computer.
Connect the smaller end of the cable into the USB port of the camcorder.
The camcorder will appear in My Computer as a drive.
Firmware upgrades
Foscam will from time to time release new firmware for enhancements or adding new features.
Visit www.foscam.us/firmware to check on the latest firmware for your FHC994.
Technical Support
To contact us, please call 1-800-930-0949, or e-mail us at support@foscam.us.
Environmental Requirements
Storage temperature: 32Ëš to 113ËšF (0Ëš to 45ËšC)
Operating temperature: 32Ëš to 113ËšF (0Ëš to 45ËšC)
FCC Regulation
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause interference to radio or television reception, which can be deter-
mined by turning the equipment off and then on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1 Increase the separation between the equipment and camcorder.
2 Connect the equipment to a different outlet so that the equipment and camcorder are
on different branch circuits.
3 Consult the dealer or an experienced radio / TV technician for help.
Disable
Disable
Scheduled Recording /
Car-activate Recording /
Car-stop Recording /
Car-activate and Car-stop Re-
cording /
(Disable)
When the FHC994 is connected to the lighter through the 5V car adapter and the auto on /off mode is selected:
Car-activated Recording: Auto-starts recording once the car is started, auto-stops recording when car is stopped.
Car-stop Recording: Auto-starts recording when car is stopped, auto-stops recording once car is started.
Car-activate and Car-stop Recording: Auto-starts recording once car is started and continues to record
even when the car is stopped. The camcorder needs to be turned off manually.
* For the longest recording time, set Video Quality to Low, Resolution to 640x360 and Frame Rate to Low. This way
the FHC994 can act as a digital voice recorder.
** If a recording is started, you cannot switch between modes.
*** If triggering is enabled, the FHC994 will record for 10 seconds after powering-up. Then it will go into standby. If there
is a trigger, it will keep recording until there are no further triggers. After that, it will record for 2 more minutes and
then standby again.
www.foscam.us
version: 1.0
Product specificaties
| Merk: | Foscam |
| Categorie: | Beveiligingscamera |
| Model: | FHC994 |
Heb je hulp nodig?
Als je hulp nodig hebt met Foscam FHC994 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Beveiligingscamera Foscam
27 Juli 2023
27 Juli 2023
27 Juli 2023
27 Juli 2023
27 Juli 2023
27 Juli 2023
27 Juli 2023
27 Juli 2023
27 Juli 2023
27 Juli 2023
Handleiding Beveiligingscamera
- Beveiligingscamera Canon
- Beveiligingscamera Honeywell
- Beveiligingscamera JVC
- Beveiligingscamera Motorola
- Beveiligingscamera Topcom
- Beveiligingscamera Abus
- Beveiligingscamera Acti
- Beveiligingscamera Alecto
- Beveiligingscamera Apc
- Beveiligingscamera Apeman
- Beveiligingscamera ATN
- Beveiligingscamera Axis
- Beveiligingscamera Beseye
- Beveiligingscamera Brinno
- Beveiligingscamera D-Link
- Beveiligingscamera Dahua
- Beveiligingscamera EasyN
- Beveiligingscamera Elro
- Beveiligingscamera Eminent
- Beveiligingscamera Escam
- Beveiligingscamera Eufy
- Beveiligingscamera Fenton
- Beveiligingscamera Ferguson
- Beveiligingscamera First Alert
- Beveiligingscamera Gembird
- Beveiligingscamera Gira
- Beveiligingscamera Hama
- Beveiligingscamera Hikvision
- Beveiligingscamera Home Protector
- Beveiligingscamera Humax
- Beveiligingscamera Iget
- Beveiligingscamera Kompernass
- Beveiligingscamera Lorex
- Beveiligingscamera Maginon
- Beveiligingscamera Mr Safe
- Beveiligingscamera Nedis
- Beveiligingscamera Netgear
- Beveiligingscamera Profile
- Beveiligingscamera SAB
- Beveiligingscamera Sinji
- Beveiligingscamera Smartwares
- Beveiligingscamera Somfy
- Beveiligingscamera Sricam
- Beveiligingscamera Storage Options
- Beveiligingscamera Swan
- Beveiligingscamera Swisstone
- Beveiligingscamera Targa
- Beveiligingscamera Tenda
- Beveiligingscamera Tenvis
- Beveiligingscamera TP Link
- Beveiligingscamera Trust
- Beveiligingscamera Ubiquiti
- Beveiligingscamera V-Tac
- Beveiligingscamera Vivotek
- Beveiligingscamera Yale
- Beveiligingscamera Jablocom
- Beveiligingscamera Overmax
- Beveiligingscamera Duramaxx
- Beveiligingscamera Nordval
Nieuwste handleidingen voor Beveiligingscamera
5 November 2024
14 November 2024
28 Oktober 2023
7 Oktober 2023
7 Oktober 2023
7 Oktober 2023
7 Oktober 2023
7 Oktober 2023
7 Oktober 2023
7 Oktober 2023