Fluke PRV240FS Handleiding

Fluke Niet gecategoriseerd PRV240FS

Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke PRV240FS (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

PRV240FS

Proving Unit

Instruction Sheet

Introduction

The PRV240FS Proving Unit (the Product) is an

electronic voltage source. This Product provides

a safe and easy method to verify proper operation

of the T6-600/T6-1000 Electrical Tester with

FieldSense technology or other test tools. Use

it to verify either an energized source or a de-

energized source. Also use it in cases where no

known voltage source is available to verify a test

tool.

The Product does not require personal protective

equipment (PPE) unless your environment

requires minimal PPE such as a hard hat, safety

glasses, or ear plugs.

How to Contact Fluke

To contact Fluke, call one of the following

telephone numbers:

●Technical Support USA: 1-800-44-FLUKE

(1-800-443-5853)

●Calibration/Repair USA: 1-888-99-FLUKE

(1-888-993-5853)

●Canada: 1-800-36-FLUKE (1-800-363-5853)

●Europe: +31 402-675-200

●Japan: +81-3-6714-3114

●China: +86-400-921-0835

●Singapore: +65-6799-5566

●Anywhere in the world: +1-425-446-5500

Or, visit Fluke's website at www.uke.com.

To register your product, visit

http://register.uke.com.

To view, print, or download the latest manual

supplement, visit

http://us.uke.com/usen/support/manuals.

Safety

A Warning identies conditions and procedures

that are dangerous to the user.

 Warning

To prevent possible electrical shock, re,

or personal injury:

●Read all safety information before you

use the Product.

●Carefully read all instructions.

●Do not alter the Product and use only as

specied, or the protection supplied by

the Product can be compromised.

●Do not touch voltages >30 V ac rms,

42 V ac peak, or 60 V dc.

●Do not use the Product around

explosive gas, vapor, or in damp or wet

environments.

PN 4919689 September 2017

Product specications are subject to change without notice.

All product names are trademarks of their respective companies.

●Do not use the Product if it operates

incorrectly.

●Examine the case before you use the

Product. Look for cracks or missing

plastic. Carefully look at the insulation

around the terminals.

●Do not use the Product if it is altered or

damaged.

●Remove the batteries if the Product is

not used for an extended period of time,

or if stored in temperatures above 50 °C.

If the batteries are not removed, battery

leakage can damage the Product.

●You must close and lock the battery

door before you operate the Product.

Symbols

Symbols used in the instructions or on the Product

are shown in Table 1.

Table 1. Symbols

Symbol Denition

Consult user documentation.

WARNING. HAZARDOUS VOLTAGE.

Risk of electric shock.

WARNING. RISK OF DANGER.

Battery

FieldSense Measurement: Fluke

voltage/current sensing technique.

Certied by CSA Group to North

American safety standards.

Conforms to relevant Australian EMC

standards.

Conforms to European Union directives.

Conforms to relevant South Korean EMC

Standards.



This product complies with the WEEE

Directive marking requirements. The

afxed label indicates that you must not

discard this electrical/electronic product

in domestic household waste. Product

Category: With reference to the equipment

types in the WEEE Directive Annex I,

this product is classed as category 9

"Monitoring and Control Instrumentation"

product. Do not dispose of this product as

unsorted municipal waste.

Operation

Table 2 is a list of the controls and interface of

the Product. See Figure 1 for the location of each

item.

Table 2. Product Overview

Item Description

AFunction selection

B+ Terminal

CAC/DC LED

D − Terminal

ETest Lead Ground Contact

FTest Lead Ground Contact LED

GFork saddle

HFinger Ground Contact LED

IFinger Ground Contact

FieldSense Measurement without Test Lead

Before verication, set up the T6 for a FieldSense

measurement without the test leads. See the

T6 Quick Reference Guide .

To verify measurement:

1. Move the switch to the FieldSense position.

See Figure 3.

2. Insert the T6 fork into position on the Product.

3. Push and hold the nger ground contact to

activate the Product.

The Product LED turns green and the T6

display shows a 240 V measurement.

FieldSense Measurement with Ground Lead

Before verication, set up the T6 for a FieldSense

measurement with the ground lead. See the

T6 Quick Reference Guide .

To verify measurement:

1. Move the switch to the FieldSense position.

See Figure 4.

2. Insert the T6 fork into position on the Product.

3. Place the black test lead from the test tool

into the test lead ground contact terminal and

press down rmly.

The Product LED turns green and the T6

display shows a 240 V measurement.

AC/DC Measurement

Before verication, set up the T6 or other test tool

for ac/dc measurement with the test leads.

To verify measurement:

1. Move the switch to the AC or DC position.

See Figure 5.

2. Place the red test lead from the test tool into

the (+) terminal and press down rmly.

3. Place the black test lead from the test tool

into the (-) terminal and press down rmly.

The Product LED turns green and the T6

display shows a 240 V measurement.

Battery Replacement

Push the nger ground contact button to check the

battery condition. The nger ground contact LED

turns green to show good battery condition. If the

LED does not turn on, replace the batteries.

 Warning

To prevent possible electrical shock, re, or

personal injury:

●Do not operate the Product with covers

removed or the case open. Hazardous

voltage exposure is possible.

●Repair the Product before use if the battery

leaks.

●Have an approved technician repair the

Product.

To replace the batteries:

1. Turn the battery-door latch until the unlock

symbol aligns with the arrow. See Figure 2.

2. Lift off the battery door.

3. Insert or replace the four AA batteries. Use

the correct battery orientation.

4. Install the battery door.

5. Turn the battery-door latch until the locked

symbol aligns with the arrow.

Specications

Output voltage

240 V ac rms or dc ±10 %

...........

≥1 MΩ

LED power indicator

.........

Turns on when output voltage is

present

Battery

...................................

4 x AA Alkaline batteries NEDA

15 A IEC LR6

Battery life

.............................

3 hr based on a 10 s test cycle or

1100 tests

Operating temperature

.....

-10 °C to +50 °C

Operating humidity

...........

0 % to 90 % (0 °C to 35 °C)

0 % to 70 % (35 °C to 55 °C)

Operating altitude

.............

2000 m

Dimensions

.......................

11.7 cm x 7.4 cm x 4.5 cm

(4.6 in x 2.9 in x 1.75 in)

Weight

................................

0.32 kg (12 oz) includes batteries

Safety

General IEC 61010-1, Pollution Degree 2

............................

Measurement IEC 61010-2-030

...................

240 Vrms/240 Vdc

Electromagnetic Compatibility (EMC)

International IEC 61326-1: Controlled

......................

Electromagnetic Environment

CISPR 11: Group 1, Class A

Group 1: Equipment has intentionally generated and/or uses

conductively-coupled radio frequency energy that is necessary

for the internal function of the equipment itself.

Class A: Equipment is suitable for use in all establishments

other than domestic and those directly connected to a low-

voltage power supply network that supplies buildings used

for domestic purposes. There may be potential difculties in

ensuring electromagnetic compatibility in other environments

due to conducted and radiated disturbances.

Caution: This equipment is not intended for use in residential

environments and may not provide adequate protection to

radio reception in such environments.

Emissions that exceed the levels required by CISPR 11 can

occur when the equipment is connected to a test object.

Korea (KCC) Class A Equipment (Industrial

.......................

Broadcasting & Communication

Equipment)

Class A: Equipment meets requirements for industrial

electromagnetic wave equipment and the seller or user

should take notice of it. This equipment is intended for use in

business environments and not to be used in homes.

USA (FCC) 47 CFR 15 subpart B. This

..........................

product is considered an exempt

device per clause 15.103.

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material

and workmanship for one year from the date of purchase.

This warranty does not cover fuses, disposable batteries,

or damage from accident, neglect, misuse, alteration,

contamination, or abnormal conditions of operation or

handling. Resellers are not authorized to extend any other

warranty on Fluke’s behalf. To obtain service during the

warranty period, contact your nearest Fluke authorized service

center to obtain return authorization information, then send

the product to that Service Center with a description of the

problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR

PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY. Since some states or countries

do not allow the exclusion or limitation of an implied warranty

or of incidental or consequential damages, this limitation of

liability may not apply to you.

Fluke Corporation Fluke Europe B.V.

P.O. Box 9090 P.O. Box 1186

Everett, WA 98206-9090 5602 BD Eindhoven

U.S.A. The Netherlands

11/99

Fluke Corporation certies this Product was tested and

veried with applicable calibration procedures during the

manufacturing process. Fluke’s quality system controls these

procedures.

The instruments used during the testing and calibration of

this Product are traceable to SI units through internationally

recognized measurement standards.

This document is not a certicate of calibration or traceability.

To obtain a certicate of calibration contact the nearest

Fluke service center to process an order to have your

Product returned for calibration. A nominal fee is charged for

calibration service.

Figure 4

LED

Figure 1

Figure 2

Figure 3

LED

Figure 5

3LED

Product specificaties

Merk:	Fluke
Categorie:	Niet gecategoriseerd
Model:	PRV240FS
Kleur van het product:	Black,Red,Yellow
Gewicht:	320 g
Breedte:	74 mm
Diepte:	45 mm
Hoogte:	117 mm
Ondersteund aantal accu's/batterijen:	4
Merkcompatibiliteit:	Fluke
Draadloze verbindingen:	0 - 2000
Bedrijfstemperatuur (T-T):	-10 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Type product:	Testeenheid
Batterijtechnologie:	Alkaline
Batterijformaat:	AA