Fluke LVD2 Handleiding

Fluke Niet gecategoriseerd LVD2

Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke LVD2 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 193 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

LVD2

VoltAlert

Safety Sheet

Read First: Safety Information

WX Warning

To prevent possible electric shock, ﬁ re, or personal injury:

● Use the Product only as speciﬁ ed, or the protection supplied by the Product

can be compromised.

● Do not rely on the Product to detect the presence or absence of voltage on

a conductor for safety purposes. A single pole non-contact voltage detector

such as this Product is not suitable to determine if a circuit is hazardous. A

volt meter or 2-pole voltage detector is necessary to conﬁ rm the absence of

hazardous voltage prior to commencing work.

● Do not use if the ﬂ ashlight does not operate.

● Detect a known voltage ﬁ rst to make sure that the Product operates correctly.

● When using the Product if tip does not glow, voltage could still be present.

The Product indicates active voltage in the presence of electric ﬁ elds of

suﬃ cient strength generated from the source (MAINS) voltage. If the ﬁ eld

strength is low, the Product may not provide indication of live voltages. Lack

of an indication occurs if the Product is unable to sense the presence of

voltage which may be inﬂ uenced by several factors including, but not limited

to:

• Shielded wire/cables

• Thickness and type of insulation

• Distance from the voltage source

• Fully-isolated users that prevent an eﬀ ective ground

• Receptacles in recessed sockets/ diﬀ erences in socket design

• Condition of the Product and Batteries

● Disable the Product if it is damaged.

● Do not use the Product if it is damaged.

● Use Product with arrow visible.

● Hold the Product behind the tactile barrier.

● Do not use for dc voltage detection or around voltages exceeding

600 volts, or in the presence of variable motor drives.

● Use caution with voltages above 30 V ac as a shock hazard may exist.

● Do not stare or look directly at the LED ﬂ ash light. The light is extremely

bright.

● Comply with local and national safety codes. Use personal protective

equipment (approved rubber gloves, face protection, and ﬂ ame-resistant

clothes) to prevent shock and arc blast injury where hazardous live

conductors are exposed.

● Batteries contain hazardous chemicals that can cause burns or explode. If

exposure to chemicals occurs, clean with water and get medical aid.

● Remove the batteries if the Product is not used for an extended period of time,

or if stored in temperatures above 50 °C. If the batteries are not removed,

battery leakage can damage the Product.

● Carefully read all instructions.

● Read all safety information before you use the Product.

PN 4572337 September 2014 Rev. 1, 10/19

FOR USE BY COMPETENT

PERSONS

Anyone using this instrument should be

knowledgeable and trained about the risks

involved with measuring voltage, especially

in an industrial setting, and the importance of

taking safety precautions and of testing the

instrument before and after using it to ensure

that it is in good working condition.

For safe operation and maintenance of the product:

● Be sure that the battery polarity is correct to prevent battery leakage.

● Repair the Product before use if the battery leaks.

Symbols

Consult user documentation.

TDouble Insulated.

XHazardous Voltage. Risk of electric shock.

WRisk of danger. Important information.

PConforms to European Union directives

)Conforms to relevant Canadian and US Standards.

Conforms to relevant Australian standards.

~This product complies with the WEEE Directive (2002/96/EC) marking

requirements. The aﬃ xed label indicates that you must not discard this

electrical/electronic product in domestic household waste. Product Category:

With reference to the equipment types in the WEEE Directive Annex I, this

product is classed as category 9 “Monitoring and Control Instrumentation”

product. Do not dispose of this product as unsorted municipal waste. Go to

Fluke’s website for recycling information.

CAT IV Measurement Category IV is applicable to test and measuring circuits

connected at the source of the building’s low-voltage MAINS installation.

Battery

Safety Speciﬁ cations

Altitude ....................................2000 m

Humidity ..................................80 % for temperatures up to 31 °C decreasing

linearly to 45 % relative humidity at 50 °C

Electrical supply .....................1.5 Vdc (1 x LR03 ‘AAA’ Battery)

Temperature ............................0 °C to 50 °C

Maximum Voltage to Earth

Ground ....................................600 V

Safety .......................................IEC61010-1:Pollution Degree 2. CAT IV 600V

Electromagnetic

Compatibility .......................... (EMC) IEC 61326-1: Portable Electromagnetic

Environment; IEC 61326-2-2

CISPR 11: Group 1, Class A

Group 1: Equipment has intentionally generated and/or use

conductively coupled radio-frequency energy which is necessary for the

internal functioning of the equipment itself.

Class A: Equipment is suitable for use in all establishments other than

domestic and those directly connected to a low voltage power supply

network which supplies buildings used for domestic purposes. There

may be potential diﬃ culties in ensuring electromagnetic compatibility in

other environments, due to conducted and radiated disturbances.

Caution: This equipment is not intended for use in residential

environments and may not provide adequate protection to radio

reception in such environments

Contacting Fluke

●Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)

●Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)

●Canada: 1-800-36-FLUKE (1-800-363-5853)

●Anywhere in the world: +1-425-446-5500

Or, visit Fluke’s website at www.ﬂ uke.com.

To register your product, visit http://register.ﬂ uke.com.

To view, print, or download the latest manual supplement, visit

http://us.ﬂ uke.com/usen/support/manuals.

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship for two years from

the date of purchase. This warranty does not cover fuses, disposable batteries, or damage

from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation

or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To

obtain service during the warranty period, contact your nearest Fluke authorized service center

to obtain return authorization information, then send the product to that Service Center with a

description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS

FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do

not allow the exclusion or limitation of an implied warranty or of incidental or consequential

damages, this limitation of liability may not apply to you.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090 U.S.A.

Fluke Europe B.V.

P.O. Box 1186

5602 BD Eindhoven

The Netherlands

11/99

Product specificaties

Merk:	Fluke
Categorie:	Niet gecategoriseerd
Model:	LVD2
Kleur van het product:	Black, Yellow
Ingebouwd display:	Nee
Certificering:	CE
Aantal per verpakking:	1 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 50 °C
Ingang operation voltage (min):	90 V
Ingang operation voltage (max):	600 V
Zakklem:	Ja