Fluke 700PV3 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke 700PV3 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
PN 602513
July 1996 Rev.3, 11/01
1996-2001 Fluke Corporation. All rights reserved. Printed in USA
15 PSID/G
PRESSURE MODULE
700
P
04
1 bar
100 kPa
RANGE
Low
High
Dierential
100 PSIG
PRESSURE MODULE
700
P
06
7 bar
700 kPa
RANGE
Gage
is1f.eps
Introduction
The Fluke 700PDX Series Pressure Modules measure
positive and negative pressure. The 700PVX modules
measure vacuum. The 700PDX modules work with the Fluke
700 Series Documenting Process Calibrators. The 700PVX
modules work only with the 740 Series Calibrators. Read this
sheet before you use the pressure module. This sheet
contains specifications and information about how to avoid
damaging the pressure module. See the calibrator’s Users
Manual for operating instructions.
Note
If you are using a Fluke-701 or Fluke-702, software
V1.3 or higher is required. See specification
footnote 1.
The pressure module measures pressure or vacuum using
an internal microprocessor. It receives operating power from
and sends digital information to the calibrator.
Gage pressure modules have one pressure fitting and
measure pressure with respect to atmospheric pressure.
Differential pressure modules have two pressure fittings and
measure the difference between the applied pressure on the
high fitting versus the low fitting. A differential pressure
module functions like a gage module when the low fitting is
open.
®
700 Series Dual-Range and
Vacuum Pressure Modules
Instruction Sheet
Box Contents
Pressure module, strap, 1/4 NPT to 1/4 ISO metric adapters
(one for gage, two for differential), and instruction sheet.
Protecting Yourself from Pressure Releases
To avoid a violent release of pressure in a pressurized
system, shut off the isolation valve and slowly bleed off the
pressure before you attach or remove the pressure module
from the pressure line.
Avoiding Overpressure Damage
Applying pressure in excess of the BURST PRESSURE
specified on the pressure module can destroy the pressure
module. Burst pressure is 3X full scale.
Table 1. Specifications 1
Model Range2Gage or
Differential
Isolated
Nonisola
Fluke-700PD2 -1 to 1.0000 psi
-6.89 to 6.8900 kPa
-6.89E-2 to 6.89 E-2 bar
Differential Isolated
Fluke-700PD3 -5 to 5.0000 psi
-34 to 34.000 kPa
-0.34 to 0.3400 bar
Differential Isolated
Fluke-700PD4 -15 to 15.000 psi
-100 to 100.00 kPa
-1 to 1.0000 bar
Differential Isolated
Fluke-700PD5 -15 to 30.000 psi
-100 to 200.00 kPa
-1 to 2.0000 bar
Gage Isolated
Fluke-700PD6 -15 to 100.00 psi
-100 to 700.00 kPa
-1 to 7.0000 bar
Gage Isolated
Fluke-700PD7 -15 to 200.00 psi
-100 to 1400.0 kPa
-1 to 14.000 bar
Gage Isolated
Fluke-700PV3 0 to -5.0000 psi
0 to -34.000 kPa
0 to -0.3400 bar
Differential Isolated
Fluke-700PV4 0 to -15.000 psi
0 to -100.00 kPa
0 to -1.0000 bar
Differential Isolated
1. Use of the pressure zero function is required to achieve these specifications
or Fluke 702 V1.0, V1.1, or V1.2 Calibrator. (PV3 and PV4 not compatible w
2. Available pressure units (psi, kPa, bar, inHg, mmHg, inH
20, ftH20, kg/cm2, mm
3. Accuracy specifications apply for 1 year for full span from 0 °C to 50 °C. Typ
4. Maximum non-destructive pressure: 3X maximum rated pressure, including
5. Maximum common mode pressure: 3X maximum rated pressure.
6. Specifications reflect a confidence interval of 95%.
Avoiding Corrosion Damage
To avoid damaging the pressure module from corrosion, use it
only with specified media as shown below:
Isolated: any medium that is compatible with type 316
stainless steel on the high side. Use dry, noncorrosive
gasses only on the low side.
Nonisolated: dry, noncorrosive gasses only.
Recommended Measurement Technique
For best results, it is recommended that the module be
pressurized to full scale and then vented to zero pressure
(atmosphere) prior to zeroing and making measurements.
Note
Low range pressure modules may be sensitive to
gravity. For best results, pressure modules 30
psi and below should be held at the same
physical orientation from the time they are
zeroed until the measurement is complete.
Pressure Calibration Kit
The Fluke-700PCK Pressure Calibration Kit makes it possible
to calibrate pressure modules at ambient temperature with a
precision pressure calibrator or dead weight tester at least 4X
better than the module specification. A 386 or better PC and
Windows® 3.1 are required. The kit is an optional accessory
available from your distributor or Fluke.
Performance Test
If you need to check that the pressure module meets its
accuracy specification, use a dead weight tester or suitable
pressure calibrator. The accuracy of the dead weight tester or
pressure calibrator should be at least 4X better than the
modules pressure specification. Proceed as follows to verify
that a pressure module is operating within specification:
1. Read the pressure value with no externally applied
pressure to make sure the 0% of scale is correct. When
reading the pressure with a 700 Series calibrator, press
the ZERO key to remove any zero offset.
Note
If you are using a Fluke-701 or Fluke-702, the
pressure ZERO function is available only with V1.3 or
higher software. Contact your Fluke Service Center
for upgrade of earlier calibrators.
2. Connect the pressure module to a dead weight tester.
3. Choose pressure test values that give approximately 20%
of full span steps.
4. Set the dead weight tester to each of these pressures and
verify that each reading is within the specification in
Table 1. Percent of full span is calculated as follows:
100% x (reading - dead weight tester setting) / (top of
span - bottom of span).
5. If temperature sensitivity is of concern, repeat steps 1
through 4 at various controlled temperatures.
Certifications
P Conforms to European Standard EN61010-1, EN61326.


Product specificaties

Merk: Fluke
Categorie: Niet gecategoriseerd
Model: 700PV3

Heb je hulp nodig?

Als je hulp nodig hebt met Fluke 700PV3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Fluke

Fluke

Fluke ii500 Handleiding

7 Oktober 2024
Fluke

Fluke iSee TC01A Handleiding

9 September 2024
Fluke

Fluke TiX885 Handleiding

7 December 2023
Fluke

Fluke TiX875 Handleiding

7 December 2023
Fluke

Fluke TiX880 Handleiding

7 December 2023
Fluke

Fluke TiX870 Handleiding

7 December 2023
Fluke

Fluke EI-162BN Handleiding

9 Augustus 2023
Fluke

Fluke CNX C3003 Handleiding

8 Augustus 2023
Fluke

Fluke 80i-2010s Handleiding

8 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd